E36 M3, MZ3 JB Racing Lightweight Aluminum Flywheel

T#:3771

Part#: 520-010-240

Ships in 9 Business Days

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.5lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
1995-1999 E36 BMW M3
1998-2002 Z3 BMW Z3 M Roadster M Coupe

Show More Show Less

E30 318i/is, E36 318i, Z3 1.9 JB Racing Lightweight Aluminum Flywheel...

T#:3769

Part#: 520-040-215

Back Ordered

11% off MSRP $ 765.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 679.00 USD

Add to Wish List

Qty

11% off MSRP

$ 765.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 679.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 27.0lbs
JB Flywheel Weight = 9.0lbs

This item fits the following BMWs:
1989-1992 E30 BMW 318i 318is 318ic
1992-1997 E36 BMW 318i 318is 318ti 318ic
1996-1997 Z3 BMW Z3 1.9

Show More Show Less

E60, E82, E85, E9X, E89 (N52 Engine) JB Racing Lightweight Aluminum F...

T#:2801

Part#: 520-200-240

In Stock

$ 714.00 USD

Add to Wish List

Qty

$ 714.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

This JB flywheel replaces the stock flywheel and can be used with either the stock 228mm or stock 240mm clutch discs. Depending on the model you may have either clutch size in your car but this flywheel is compatible with both. You can install a 240mm clutch as a mild upgrade.

Stock Flywheel Weight = 24-31.0lbs
JB Flywheel Weight = 12.0lbs

This item fits the following BMWs:
2006-2010 E60 BMW - 525i, 528i, 530i
2006-2013 E90, E91, E92, E93 BMW - 325i, 328i, 330i
2007-2013 E82 BMW - 125i, 128i
2006-2008 E85, E86 BMW - Z4 3.0i, Z4 3.0si
2009-later E89 BMW - Z4 3.0i

Show More Show Less

E46 M3 6MT JB Racing Lightweight Aluminum Flywheel

T#:302739

Part#: 520-180-240

Ships in 8 Business Days

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
2001-2006 E46 BMW M3 (6-speed manual only, not for SMG)

Show More Show Less

E46 323/325/328/330 5-speed, Z3 2.3/2.8/3.0 JB Racing Lightweight Alu...

T#:4227

Part#: 520-140-240

In Stock

$ 602.00 USD

Add to Wish List

Qty

$ 602.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch). In addition to the standard replacement clutches, we also sell Sachs Performance sprung hub clutches that also work with the JB flywheels.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (with 5-speed manual transmission)
2001-2005 E46 BMW 325xi 330xi
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i

Show More Show Less

E30 M3 JB Racing Lightweight Aluminum Flywheel

T#:3768

Part#: 520-050-228

Ships in 4 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB flywheel includes ignition trigger wheel.

Stock Flywheel Weight = 19.5lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1987-1991 E30 BMW M3

Show More Show Less

JB Racing Single Mass Lightweight Aluminum Flywheel - 6-speed - E46 3...

T#:3474

Part#: 520-190-240

Ships in 2 Business Days

$ 672.00 USD

Add to Wish List

Qty

$ 672.00 USD

Add to Wish List

This is a performance replacement for BMW Part # 21207533868 Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB Flywheel includes the pilot bearing mounted in the flywheel hub, just like the factory configuration.

Stock Flywheel Weight = 25.0lbs
JB Flywheel Weight = 10.5lbs

This item fits the following BMWs:
2002-2005 E46 BMW 325i 330i (with 6-speed manual transmission)

Show More Show Less

E30 325i, E34 525i (M20) JB Racing Lightweight Aluminum Flywheel (Rep...

T#:385699

Part#: 520-060-228

Ships on Aug 28, 2026

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

This flywheel replaces the stock original single-mass flywheel and should only be used with the corresponding 'single-mass' clutch kit. According to BMW the single mass flywheel was installed in all 325i up to 12/86 production date but we have seen some later cars with a single-mass flywheel. The age of the car almost guarantees one or more clutch replacements and possibly a change to the original flywheel as well. You may not know which flywheel is currently installed until the flywheel cover or the transmission is removed.

Stock Flywheel Weight = 18.0lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1984-1991 E30 BMW 325i 325ic 325is (with single-mass flywheel)
1989-1990 E34 BMW 525i (with single-mass flywheel)

Show More Show Less

E34 M5 JB Racing Lightweight Aluminum Flywheel

T#:3772

Part#: 520-090-240

Ships in 9 Business Days

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable.

Stock Flywheel Weight = 16.0lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1991-1995 E34 BMW M5

Show More Show Less

2002, E21 320i, E30 318i (M10) JB Racing Lightweight Aluminum Flywhee...

T#:3647

Part#: 520-110-215

Ships in 2 Business Days

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can be rebuilt too with a new clutch contact surface.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 16.5lbs
JB Flywheel Weight = 8lbs

This item fits the following BMWs:
1974-1976 2002 BMW 2002
1977-1983 E21 BMW 320i
1984-1985 E30 BMW 318i

Show More Show Less

E39 540i 97-03 JB Racing Lightweight Aluminum Flywheel

T#:1339

Part#: 520-150-240

In Stock

$ 903.00 USD

Add to Wish List

Qty

$ 903.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 33.0lbs
JB Flywheel Weight = 13.0lbs

This item fits the following BMWs:
1997-2003 E39 BMW 540i

Show More Show Less

Ina Clutch Release/Throw-out Bearing - E46, E53, E60, E83, Z4 ...

We Price Match - Give Us A Call or Chat!

T#:19646

Part#: 21517521360

Ships in 1 Business Day

$ 74.38

This product was last offered at the strikethrough price on
07-03-2026

$ 73.53 USD

Add to Wish List

Qty

$ 73.53 USD

Add to Wish List

CLUTCH CLUTCH RELEASE BEARING

Valeo Single Mass Clutch Kit - E46 325xi (Thru 08/03), 330i 5 speed (...

We Price Match - Give Us A Call or Chat!

T#:3578

Part#: 21207531843

Ships in 1 Business Day

$ 896.33 USD

Add to Wish List

Qty

$ 896.33 USD

Add to Wish List

Single mass flywheels can be resurfaced while it is recommended that dual mass flywheels are not.
Dual mass flywheels contain a rubber damper that will wear out, single mass flywheels do not have this and are inherently easier to maintain
Single mass flywheels also provide more consistent clutch feel when compared to the dual mass "self-adjusting" clutch that is notorious for inconsistency.
Valeo's single mass flywheel conversion is designed to be a similar weight and mass to OEM, making it an ideal choice for a daily driver

Show More Show Less

E24 633/635CSi/M6, E28 535i/M5 JB Racing Lightweight Aluminum Flywhee...

T#:3770

Part#: 520-080-240

Ships in 8 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 22.0lbs
JB Flywheel Weight = 8.5lbs

This flywheel includes the ignition trigger wheel.

This item fits the following BMWs:
1982-1987 E23 BMW 733i 735i
1982-1989 E24 BMW 633csi 635csi M6
1985-1988 E28 BMW 535i 535is M5

Show More Show Less

Single Mass Flywheel Conversion Kit 52151203 - R52 / R53

We Price Match - Give Us A Call or Chat!

T#:585277

Part#: 52151203

In Stock

$ 585.99 USD

Add to Wish List

Qty

$ 585.99 USD

Add to Wish List

Valeo Dual Mass Flywheel Conversion Kit for MINI Cooper S/JCW

Elevate your MINI's performance with the Valeo dual mass flywheel conversion kit. This comprehensive kit includes a solid flywheel, pressure plate, clutch disc, throw-out bearing, and more. Notably, it replaces the OE dual mass flywheel for enhanced performance.

If you're missing any hardware, don't worry. Valeo ensures your satisfaction by replacing missing items with your order number. They are also working on an improved box design to prevent damage during shipping.

Designed for the R53/R52 Cooper S/JCW with W11 engines (Supercharged Engines), this kit is not compatible with Gen 2 MINIs (R56) with N14/N18+ Turbo Engines. For an exclusive ECS Tuning kit with extra seals, explore ES3469345.

Upgrade to the single mass setup for cost-efficiency, serviceability, simplicity, and enhanced driveability. Valeo's conversion kit maintains clutch and flywheel weight for quiet and easy driving.

This kit includes a replacement flywheel, clutch disc, pressure plate, release bearing, and more. Please note that a lightened single mass flywheel may result in some "NVH" or "chatter" during operation, which can be influenced by accompanying modifications.

For complete install kits, discover ES3469345 and ES4067131, exclusively at ECS Tuning.

Installation Details:

Flywheel bolts (M10x19.5): Tightening torque 90 Nm, Thread lock red.
Pressure plate (M7x26): Tightening torque 20 Nm.

Show More Show Less

JB Racing Lightweight Aluminum Flywheel - E39 M5

T#:16606

Part#: 520-160-240

Ships in 8 Business Days

$ 903.00 USD

Add to Wish List

Qty

$ 903.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 40.0lbs
JB Flywheel Weight = 13.0lbs

This item fits the following BMWs:
1999-2003 E39 BMW M5

Show More Show Less

Stage 3 Performance Twin Disc Clutch Kit - Single Mass Flywheel - E8X...

T#:640069

Part#: MS-006-076

Ships on Jan 8, 2027

$ 1,299.99 USD

Add to Wish List

Qty

$ 1,299.99 USD

Add to Wish List

Working in collaboration with Competition Clutch, the up and coming German automotive performance company DKM has released a new line of high quality clutches made to satisfy your stock and modified performance needs! If you're having problems keeping power to the wheels, DKM has the solution. Their design, using high-grade materials, gives you increased strength and heat tolerance preventing wear and fade, ensuring increased torque capacity, quicker shifts, and a longer clutch life. Tracking your vehicle is all fun and games until your start burning through clutches as fast as you can afford to replace them. To end this cycle, the MS Twin Disc Clutch Kit is designed to hold up to 100 to 200% more torque capacity and provide you with a much improved clutch life span. The two organic disc setup provides additional contact surface areas to more evenly distribute pressure and heat for both a boost in performance and wear prevention. Kit Contents: Pressure Plate Two Organic Discs Steel Single Mass Flywheel Pilot Bearing/Bushing and Throw-out Bearing (when applicable) Alignment Tool **Due to the nature of lightened single mass flywheels added "NVH" or "chatter" will or may occur during operation. Accompanying modifications can also increase or decrease the amount of "NVH" or "chatter" in the drivetrain. Please contact our sales team with any questions.**

Show More Show Less

2002, 2002Tii JB Racing Lightweight Aluminum Flywheel 228mm

T#:3762

Part#: 520-100-228

In Stock

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can be rebuilt too with a new clutch contact surface.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 16.5
JB Flywheel Weight = 8lbs

This item fits the following BMWs:
1968-1973 2002 BMW 2002 2002tii

Show More Show Less

BMW E36 328i, Z3 2.8 JB Racing Lightweight Aluminum Flywheel ...

T#:3774

Part#: 520-030-240

In Stock

$ 714.00

This product was last offered at the strikethrough price on
06-08-2026

$ 652.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 714.00

This product was last offered at the strikethrough price on
06-08-2026

$ 652.99 USD

Limited Qty Sale

Add to Wish List

BMW E36 328i, Z3 2.8 JB Racing Lightweight Aluminum Flywheel offers a significant performance upgrade by replacing the heavy stock steel flywheel with a much lighter aluminum version. This JB Racing flywheel is designed to deliver faster acceleration, improved throttle response, and enhanced overall performance for your BMW.

The modern stock flywheels are burdened with additional components meant to dampen vibrations, which unfortunately adds unnecessary weight. The JB Racing aluminum flywheel, weighing just 10.0 lbs compared to the stock 25.0 lbs, eliminates this excess mass, allowing more power to reach the wheels and reducing the energy wasted on spinning the flywheel. Engine builders prioritize lightweight flywheels when optimizing race engines for maximum efficiency, and the difference is especially noticeable in how quickly the engine revs and reaches its power band.

This JB Racing lightweight flywheel is a direct replacement for the stock flywheel and is compatible with the factory BMW organic clutch. This compatibility ensures that you can use standard replacement clutches, making maintenance simple and cost-effective. The flywheel can also be resurfaced for a fresh contact surface, so there’s no need to buy a new one when it’s time to replace the clutch.

While single-mass aluminum flywheels like this one may result in slightly more noise and vibration compared to dual-mass designs, this can be managed with heavier transmission oil and sprung hub clutches, such as the Sachs Performance clutch available through Turner Motorsport.

Faster acceleration: Reduces the rotational mass for quicker engine response.
Improved throttle response: Engine revs more freely and builds RPM faster.
Enhanced performance: More power delivered to the wheels for better driving dynamics.
Cost-effective maintenance: Compatible with factory BMW organic clutches and can be resurfaced.
Direct replacement: Easy upgrade with no modifications required.

Vehicle Compatibility:

1996-1999 E36 BMW 328i, 328is, 328ic
1997-1998 Z3 BMW Z3 2.8

Show More Show Less

E30 325e JB Racing Lightweight Aluminum Flywheel (Replaces Single-Mas...

T#:3763

Part#: 520-070-228

Ships in 5 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB flywheel includes ignition trigger wheel.

This flywheel replaces the stock original single-mass flywheel and should only be used with the corresponding 'single-mass' clutch kit. According to BMW the single mass flywheel was installed in all 325e up to 5/86 production date but we have seen some later cars with a single-mass flywheel. The age of the car almost guarantees one or more clutch replacements and possibly a change to the original flywheel as well. You may not know which flywheel is currently installed until the flywheel cover or the transmission is removed.

Stock Flywheel Weight = 24.0lbs
JB Flywheel Weight = 8.5lbs

This item fits the following BMWs:
1984-1988 E30 BMW 325e 325es (with single mass flywheel)

Show More Show Less

Valeo Clutch Kit - E28, E30, E34, E36

We Price Match - Give Us A Call or Chat!

T#:379443

Part#: 21211223546

Back Ordered

$ 362.99 USD

Add to Wish List

Qty

$ 362.99 USD

Add to Wish List

Replace your worn or slipping clutch to restore drivability. Comprehensive kit includes pressure plate, clutch disc, throw out bearing, pilot bearing, and clutch alignment tool.

Valeo Single Mass Flywheel Conversion Kit - E28, E30, E34, E36 ...

We Price Match - Give Us A Call or Chat!

T#:377153

Part#: 52281208

Ships in 1 Business Day

$ 807.22 USD

Add to Wish List

Qty

$ 807.22 USD

Add to Wish List

Upgrade from your failure prone dual mass flywheel with this kit. Includes single mass flywheel, clutch kit and hardware.

E36, E46 JB Racing Ultra-Light Racing Clutch/Flywheel Assembly ...

T#:340509

Part#: WCCLUTCH

Ships in 5 Business Days

Starting at $ 1,999.00 USD

Add to Wish List

Starting at $ 1,999.00 USD

Add to Wish List

The ultimate in a racing flywheel and clutch! This was developed for use in our E36 and E46 World Challenge Touring Cars. The combined weight of the clutch and flywheel is only 11lbs!!!

This multi-disc (2 or 3 disc setups) offer a minimal flywheel mass (enough to include a factory ring gear for the starter) and a small 5.5" clutch assembly rated to 500hp. By saving as much weight as possible less energy is used in simply spinning the flywheel/clutch assembly and that means a lot more power and torque is available at the drive wheels. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines and this is among the most advanced and lightest racing clutch kits available for your BMW race car.

The JB Ultra-Light Performance racing clutch is available in 2-disc or 3-disc setups. We used the 5.5"/140mm size in our Touring Cars but larger sizes are available too. This is a turn-key racing clutch and flywheel kit that you don't have to engineer or spec yourself. This is the same clutch setup we used when winning the 2003 and 2004 Touring Car Championships - the quality and performance is unquestionable. That series also employed standing starts at each race and this clutch setup performed flawlessly with nearly a full season of racing on them before needing a change.

JB Ultra-Light flywheels include:

precision CNC machined aluminum flywheel

zero-balanced up to 10,000 RPM

replaceable hardened steel clutch friction surface

Helicoil threaded inserts

high-strength grade 10.9 hardware

multi-disc racing clutch with Performance racing pressure plate

JB Racing throw-out bearing with custom bobbin
This is a true racing clutch and will not function as a street-able clutch at all. It behaves as an on/off switch with no slippage allowed. Extreme care must be used when driving on to trailers and around the paddock. But when driven correctly the life span of this clutch is amazing - we could get a full season of racing a 300hp M54 from this clutch setup including standing starts at every race! Replacement clutch components and flywheel rebuilding are available.

A properly adjusted clutch stop is required for use with this clutch kit.

Stock Flywheel + Clutch Weight = 45+lbs
JB Ultra-Light Flywheel & Clutch Weight = 11lbs

This item fits the following BMWs:
1992-1999 E36 BMW 325i 325is 328i 328is M3
1999-2006 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (5-speed)
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2005 E85 BMW Z4 2.5i (5-speed)

Show More Show Less

E30 325e JB Racing Lightweight Aluminum Flywheel (Replaces Dual-Mass ...

T#:3749

Part#: 520-120-228

In Stock

$ 854.00 USD

Add to Wish List

Qty

$ 854.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

The JB flywheel includes ignition trigger wheel.

This flywheel replaces the stock original dual-mass flywheel and should only be used with the corresponding 'dual-mass' clutch kit. According to BMW the dual mass flywheel was installed in all 325/325e from 5/86 on but we have seen some later cars with a single-mass flywheel. The age of the car almost guarantees one or more clutch replacements and possibly a change to the original flywheel as well. You may not know which flywheel is currently installed until the flywheel cover or the transmission is removed.

Stock Flywheel Weight = 27.5lbs
JB Flywheel Weight = 10.0lbs

This item fits the following BMWs:
1984-1988 E30 BMW 325e 325es (with dual mass flywheel)

Show More Show Less

Valeo Single Mass Flywheel Conversion Kit - E36, E39, Z3

We Price Match - Give Us A Call or Chat!

T#:377152

Part#: 52401210

Ships in 1 Business Day

$ 969.21 USD

Add to Wish List

Qty

$ 969.21 USD

Add to Wish List

Upgrade from your failure prone dual mass flywheel with this kit. Includes single mass flywheel, clutch kit and hardware.

Z4 M HD Clutch and Flywheel Kit

T#:878

Part#: 520-010S-S873G

Ships in 9 Business Days

$ 1,488.61 USD

Add to Wish List

Qty

$ 1,488.61 USD

Add to Wish List

This lightweight aluminum flywheel w/ Heavy Duty "sprung-hub" clutch package is the best-engineered solution for E46 325 and 330 models with the 6-speed transmission, Z4 2.5/3.0, and Z4 M Roadster and M Coupe. Instead of picking a clutch from another car that may or may not work at all, the engineers at JB Racing have taken all of the guess work out of this upgrade and incorporated a Sachs sport sprung-hub clutch with the correct pressure plate and combined it with their most-popular aluminum lightweight flywheel. The Sachs HD clutch disc has a sprung hub to minimize noise and vibration and organic linings to give the feel and engagement of a stock clutch. Mixing and matching of the incorrect clutch, pressure plate, and flywheel components can lead to inconsistent engagement and feel -- why make your clutch feel worse?

In addition, the Sachs HD pressure plate will clamp with greater force -- allowing approximately 350 ft-lbs of torque, which makes it an obvious upgrade from the stock clutch kit. And with the aluminum flywheel weight savings is substantial over the stock dual-mass flywheel - which allows your motor to spool up faster and transmit more HP to the ground.

Because Sachs is an OE supplier to most German cars, replacement parts are just a phone call away. This kit uses the stock throw-out bearing (included in the price).

Z4 M Sport Clutch and Flywheel Applications:
2006-2008 E85 Z4, E86 Z4 Z4 M Roadster, Z4 M Coupe

Show More Show Less

Valeo Single Mass Flywheel Conversion Kit - E60 E82/88 E9X Z4 N52 3.0...

We Price Match - Give Us A Call or Chat!

T#:383915

Part#: 835115

In Stock at Vendor

$ 1,388.30 USD

Add to Wish List

Qty

$ 1,388.30 USD

Add to Wish List

This kit from Valeo is a simple way to easily convert your stock dual mass flywheel clutch system to a single mass system.

Dual mass flywheels allow for fluid-feeling clutch engagements and offer a more luxurious feel than single-mass flywheels. However, with these benefits come significant drawbacks. Why convert from a dual-mass flywheel to a single-mass flywheel?

Cost: Dual-mass flywheels are expensive, with the cost of replacement often times being double or triple than that of converting to a single-mass flywheel.
Serviceability: Single-mass flywheels can be resurfaced, eliminating the need to replace with the next clutch service. - something that is not recommended with dual-mass flywheels, as they contain a rubber section that is more failure-prone in high mileage application.
Simplicity: Single-mass flywheels lack the complexity of dual-mass flywheels, making them inherently more reliable. Dual-mass flywheels contain a rubber damper or hub that will, like all rubber components, wear out with time.
Pedal Feel: Many enthusiasts prefer to eliminate BMW's "Self Adjusting Clutch", which has been known to provide an unpredictable, inconsistent engagement point.
Driveability: Valeo's conversion kit has been designed to maintain nearly identical clutch and flywheel weight, ideal for keeping the clutch quiet and easy to drive.
Kit contents:

Single-mass flywheel
Non-Self Adjusting Clutch and pressure plate
Throw out bearing
Pressure plate bolts
Flywheel bolts
Clutch alignment tool

Show More Show Less

Valeo Single Mass Clutch Kit - 330i 6 speed

We Price Match - Give Us A Call or Chat!

T#:400593

Part#: 835101

Back Ordered

$ 1,242.99 USD

Add to Wish List

Qty

$ 1,242.99 USD

Add to Wish List

MINI R52 R53 Clutch Kit For Solid Flywheel Conversion 52151204 ...

We Price Match - Give Us A Call or Chat!

T#:2211795

Part#: 52151204

Ships in 3 Business Days

$ 294.99 USD

Add to Wish List

Qty

$ 294.99 USD

Add to Wish List

MINI R52 R53 Clutch Kit For Solid Flywheel Conversion

Upgrade your Mini's clutch system with the MINI R52 R53 Clutch Kit For Solid Flywheel Conversion. Specifically designed for solid flywheel conversion, this clutch kit ensures optimal performance and durability for your Mini. Say goodbye to clutch issues and enjoy smoother engagements and reliable performance on the road.

Designed for solid flywheel conversion
Ensures optimal clutch performance
Provides smoother engagements
Enhances reliability on the road
Made for durability

Show More Show Less

E34 535i JB Racing Lightweight Aluminum Flywheel

T#:647

Part#: 520-170-240

Ships in 1 Business Day

$ 714.00 USD

Add to Wish List

Qty

$ 714.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Show More Show Less

OS Giken E9X M3 Clutch Overhaul Kit (for Grand Am Legal Racing Flywhe...

T#:2209

Part#: BM533-BF6EA

Ships in 2 Business Days

$ 999.99 USD

Add to Wish List

Qty

$ 999.99 USD

Add to Wish List

This kit includes parts needed to overhaul the OS Giken E90/E92 M3 Grand Am legal clutch kit, including clutch discs (2), center plates, and cover bolts (all). As used in the Grand Am KONI Challenge GS class V8 M3s, including both Turner Motorsport E92 M3 race cars.

Show More Show Less

MS Twin Disc Clutch Kit for E36 M3

T#:639553

Part#: MS-006-005

Special Order: No Guaranteed ETA

$ 1,299.99 USD

Add to Wish List

Qty

$ 1,299.99 USD

Add to Wish List

Turner Motorsport presents the MS Twin Disc Clutch Kit (MS-006-005) by DKM®, an exceptional clutch solution designed for BMW applications. Engineered to handle 100 to 200% more torque capacity, this twin disc kit features sprung organic discs, providing increased contact surface for higher torque capacity and an extended lifecycle. The kit includes a pressure plate, organic discs, steel flywheel, pilot bearing/bushing, throw-out bearing, and alignment tool for a comprehensive clutch upgrade.

High Torque Capacity: Holds 100 to 200% more torque to the wheels.
Durable Construction: Sprung organic discs for longevity and increased contact surface.
Complete Kit: Includes pressure plate, discs, steel flywheel, pilot bearing/bushing, throw-out bearing, and alignment tool.
CNC Machined Components: Ensures precision and reliability.
Powerful Performance: Rated for upwards of 650 ft/lbs of torque.
Billet Steel Flywheels: Enhances strength and durability.
Practicable Pedal Feel: Offers sport-inspired performance without sacrificing pedal feel.
Factory-Like Engagement: Maintains a close-to-factory engagement.
Street Capable: Ideal for high horsepower street applications.

Upgrade your BMW's clutch performance with the MS Twin Disc Clutch Kit from Turner Motorsport.

Show More Show Less

E9X M3 OS Giken High Performance Racing Clutch & Flywheel Kit ...

T#:338592

Part#: BM533-BF6

Ships in 2 Business Days

Starting at $ 2,150.00 USD

Add to Wish List

Starting at $ 2,150.00 USD

Add to Wish List

This racing flywheel and clutch kit is made by renowned drivetrain specialist OS Giken. Complete fly wheel & clutch setup as used on our own TMS E92 M3 race cars. This setup is ideal for both endurance racing or high horsepower applications that have very limited street use but require more clamping power than stock. It has been approved for use in the GRAND AM Continential Challenge GS race class, approved by GRAND AM rules and regulations.

Includes flywheel, clutch discs (2 disc clutch), center plate, pressure plate, aluminum cover, 360 degree housing (for clutch assembly), cover bolts, flywheel bolts, throw-out bearing, and release sleave assembly. Weighs 5% less than the stock E90/E92 M3 flywheel and clutch setup. This setup is intended for racing use only (not for daily driven street cars.) We recommend using the OS Giken clutch alignment tool during installation (sold separately).

Show More Show Less

JB Racing Aluminum Lightweight Flywheel - E9X M3

T#:5774218

Part#: 520-210-215

Ships in 5 Business Days

$ 1,106.00 USD

Add to Wish List

Qty

$ 1,106.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Show More Show Less

Valeo Single Mass Flywheel Conversion Kit - E39 E46 Z3 M52 2.5L ...

We Price Match - Give Us A Call or Chat!

T#:380538

Part#: 52401225

Ships on Sep 8, 2026

$ 1,016.99 USD

Add to Wish List

Qty

$ 1,016.99 USD

Add to Wish List

This kit from Valeo is a simple way to easily convert your stock dual mass flywheel clutch system to a single mass system.

Dual mass flywheels allow for fluid-feeling clutch engagements and offer a more luxurious feel than single-mass flywheels. However, with these benefits come significant drawbacks. Why convert from a dual-mass flywheel to a single-mass flywheel?

Cost: Dual-mass flywheels are expensive, with the cost of replacement often times being double or triple than that of converting to a single-mass flywheel.
Serviceability: Single-mass flywheels can be resurfaced, eliminating the need to replace with the next clutch service. - something that is not recommended with dual-mass flywheels, as they contain a rubber section that is more failure-prone in high mileage application.
Simplicity: Single-mass flywheels lack the complexity of dual-mass flywheels, making them inherently more reliable. Dual-mass flywheels contain a rubber damper or hub that will, like all rubber components, wear out with time.
Pedal Feel: Many enthusiasts prefer to eliminate BMW's "Self Adjusting Clutch", which has been known to provide an unpredictable, inconsistent engagement point.
Driveability: Valeo's conversion kit has been designed to maintain nearly identical clutch and flywheel weight, ideal for keeping the clutch quiet and easy to drive.
Kit contents:

Single-mass flywheel
Non-Self Adjusting Clutch and pressure plate
Throw out bearing
Pressure plate bolts
Flywheel bolts
Clutch alignment tool

Show More Show Less

Valeo Replacement Clutch Kit for Valeo Single Mass Conversion - E36, ...

We Price Match - Give Us A Call or Chat!

T#:580071

Part#: 828093

Ships on Sep 8, 2026

$ 606.99 USD

Add to Wish List

Qty

$ 606.99 USD

Add to Wish List

Replacement clutch kit from Valeo for the single mass flywheel conversion kit (ES2702806)

MINI R Chassis OS Giken Clutch Kit - STR Series

T#:30164597

Part#: MN023-BJ5

Back Ordered

$ 1,920.00 USD

Add to Wish List

Qty

$ 1,920.00 USD

Add to Wish List

MINI R Chassis OS Giken Clutch Kit - STR Series enhances performance and durability for your BMW or MINI. This high-performance clutch kit from OS Giken is designed specifically for MINI R chassis models, offering improved torque capacity and durability. With its STR series design, it ensures smooth engagement and precise control, perfect for both street and track applications. Engineered with high-quality materials, this clutch kit provides reliable performance under demanding conditions.

Enhances performance and durability
Designed specifically for MINI R chassis models
Improved torque capacity for enhanced power transfer
STR series design ensures smooth engagement
Suitable for both street and track use

Upgrade your BMW or MINI R chassis with the MINI R Chassis OS Giken Clutch Kit - STR Series for superior clutch performance and reliability.

Show More Show Less

Valeo Clutch Kit - E39, E46, Z3

We Price Match - Give Us A Call or Chat!

T#:378253

Part#: 52401223

Ships in 6 Business Days

$ 526.99 USD

Add to Wish List

Qty

$ 526.99 USD

Add to Wish List

Includes pressure plate, throw out bearing, and friction disc

INA Clutch Pilot Bearing

We Price Match - Give Us A Call or Chat!

T#:399014

Part#: 034105313A

In Stock

$ 8.15

This product was last offered at the strikethrough price on
06-16-2026

$ 6.99 USD

Add to Wish List

Qty

$ 6.99 USD

Add to Wish List

Whenever you replace your clutch, you want to be sure that every single part that can be serviced while disassembled is new and in great shape. This saves you time down the road if a small component not serviced in a clutch change fails. This is a perfect replacement for your clutch pilot bearing with the same outside and inside diameter. A great way to be sure that everything installed during your clutch change works in harmony.

Show More Show Less

OS Giken Throw Out Bearing Only For OS Giken Clutch Kit

T#:54388400

Part#: MN023-AJ60K

Ships in 5 Business Days

$ 150.00 USD

Add to Wish List

Qty

$ 150.00 USD

Add to Wish List

Throw out bearing for OS Giken clutches

OS Giken Clutch Kit - Grand Touring Series - Mini R5X

T#:23383349

Part#: MN023-AQ6

Ships in 3 Business Days

$ 1,680.00 USD

Add to Wish List

Qty

$ 1,680.00 USD

Add to Wish List

Introducing the Mini Grand Touring Clutch, a revolutionary addition to the clutch lineup. This clutch incorporates cutting-edge technology from our Racing Multi-plate Clutches, enhanced further by our exclusive "floating pressure system." Say goodbye to rough and noisy drives - experience a seamless and chatter-free driving sensation. The Mini Grand Touring Clutch is offered in both single and twin plate configurations, with options for soft or hard clutch covers to cater to various engine outputs. Achieve a maximum torque of 315 FT/LBS with this innovative clutch.

Incorporates advanced "floating pressure system" for a smooth driving experience
Retains technology from Racing Multi-plate Clutches
Available in single and twin plate configurations
Options for soft or hard clutch covers to suit engine output

Show More Show Less

E46 M3 Dual Ceramic Clutch Kit - With Single Mass Flywheel

T#:24610565

Part#: MR-006-054

Special Order: No Guaranteed ETA

$ 1,699.99 USD

Add to Wish List

Qty

$ 1,699.99 USD

Add to Wish List

Rated for upwards of 650 ft/lbs, this multi-plate (Twin Disc) Clutch is sure to have the clamping force your E46 M3 needs. Equipped with dual 184mm ceramic discs, DKM (Der Kupplungmeister) has mastered the art of packing loads of clamping force into a small space. Kit Includes: 184mm Ceramic Clutch Discs - 2 Flywheel - 1 Pressure Plate - 1 All Hardware Throwout Bearing - 1 Clutch Alignment Tool - 1

Show More Show Less

E46 M3 Dual Ceramic Clutch Kit - With Single Mass Flywheel

T#:24610569

Part#: MRX-006-005

Special Order: No Guaranteed ETA

$ 1,799.99 USD

Add to Wish List

Qty

$ 1,799.99 USD

Add to Wish List

Rated for upwards of 850 ft/lbs, this multi-plate (Twin Disc) Clutch is sure to have the clamping force your E46 M3 needs. Equipped with dual 215mm ceramic discs, DKM (Der Kupplungmeister) has mastered the art of packing loads of clamping force into a small space. Kit Includes: 215mm Ceramic Clutch Discs - 2 Flywheel - 1 Pressure Plate - 1 All Hardware Throwout Bearing - 1 Clutch Alignment Tool - 1

Show More Show Less

E46 M3 JB Racing Ultra-Light Racing Clutch/Flywheel Assembly ...

T#:340510

Part#: WCCLUTCH-E46M3

Ships in 5 Business Days

Starting at $ 2,015.99 USD

Add to Wish List

Starting at $ 2,015.99 USD

Add to Wish List

The ultimate in a racing flywheel and clutch! This was developed for use in our E36 and E46 World Challenge Touring Cars. The combined weight of the clutch and flywheel is only 11lbs!!!

This multi-disc (2 or 3 disc setups) offer a minimal flywheel mass (enough to include a factory ring gear for the starter) and a small 5.5" clutch assembly rated to 500ft-lbs. By saving as much weight as possible less energy is used in simply spinning the flywheel/clutch assembly and that means a lot more power and torque is available at the drive wheels. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines and this is among the most advanced and lightest racing clutch kits available for your BMW race car.

The JB Ultra-Light Performance racing clutch is available in 2-disc or 3-disc setups. A 3-disc setup is less susceptible to heat and will have a higher torque capacity. On our M54-powered 325i Touring Cars (approximately 300hp) we used the 5.5"/140mm 2-disc configuration. The 5.5" clutch was a perfect blend of performance and durability. It wasn't too small to suffer from high temperatures and wasn't too large that it couldn't be slipped (slipping prevents damage to other components). This is a turn-key racing clutch and flywheel kit that you don't have to engineer or spec yourself. This is the same clutch setup we used when winning the 2003 and 2004 Touring Car Championships - the quality and performance is unquestionable. That series also employed standing starts at each race and this clutch setup performed flawlessly with nearly a full season of racing on them before needing a change.

JB Ultra-Light flywheels include:

precision CNC machined aluminum flywheel

zero-balanced

replaceable hardened steel clutch friction surface

Helicoil threaded inserts

high-strength grade 10.9 hardware

multi-disc Sachs or Powertrain Technology racing clutch with racing pressure plate

JB Racing throw-out bearing with custom bobbin
This is a true racing clutch and will not function as a street-able clutch at all. It behaves as an on/off switch with no slippage allowed. Extreme care must be used when driving on to trailers and around the paddock. But when driven correctly the life span of this clutch is amazing - we could get a full season of racing a 300hp M54 from this clutch setup including standing starts at every race! Replacement clutch components and flywheel rebuilding are available.

A properly adjusted clutch stop is required for use with this clutch kit.

Stock Flywheel + Clutch Weight = 45+lbs
JB Ultra-Light Flywheel & Clutch Weight = 11lbs

This item fits the following BMWs:
2001-2006 E46 BMW M3

Show More Show Less

Aasco Solid Billet Steel Flywheels N18 MINI Cooper

T#:37521038

Part#: 03-655

Ships on Aug 28, 2026

$ 799.99 USD

Add to Wish List

Qty

$ 799.99 USD

Add to Wish List

21lbs Dual Mass Conversion Clutch Kit 28 Spline 6 Speed

T#:26238503

Part#: 03-655S

Ships on Aug 28, 2026

$ 1,128.99 USD

Add to Wish List

Qty

$ 1,128.99 USD

Add to Wish List

JMTC MINI Cooper S Solid Flywheel Conversion Clutch Kit

Upgrade your Mini's clutch system with JMTC's MINI Cooper S Solid Flywheel Conversion Clutch Kit. This kit offers a direct replacement for the OEM dual mass flywheel and clutch set, providing enhanced durability and performance.

Key Benefits:

Direct replacement for OEM dual mass flywheel and clutch set
Solid single mass flywheel ensures durability and reliability
Interchangeable with OEM clutch sets and components
Steel surface can be refinished for extended use
Thicker friction surface area for better heat absorption and distribution
Resistant to catastrophic failure
Made with Clutchtex Kevlar and Miba Ceramics for extended life
Includes clutch disc, centering tool, pressure plate, release bearing, and bolts
No break-in period for ceramic clutch, while Kevlar clutch may take up to 1000 miles
Installation kit and new master clutch cylinder recommended for optimal performance and longevity

Upgrade your Mini's clutch system today with JMTC's reliable and performance-driven clutch kit.

Show More Show Less

DKM MSC Segmented Ceramic Twin-Disc Clutch Kit W/ Flywheel - 240mm - ...

T#:5987856

Part#: MSC-006-076

Special Order: No Guaranteed ETA

$ 1,699.99 USD

Add to Wish List

Qty

$ 1,699.99 USD

Add to Wish List

Working in collaboration with Competition Clutch, the up-and-coming German automotive performance company DKM has released a new line of high-quality clutches made to satisfy your stock and modified performance needs! If you're having problems keeping power to the wheels, DKM has the solution. Their design, using high-grade materials, gives you increased strength and heat tolerance preventing wear and fade, ensuring increased torque capacity, quicker shifts, and longer clutch life. Tracking your vehicle is all fun and games until your start burning through clutches as fast as you can afford to replace them. To end this cycle, the MSC Twin Ceramic Disc Clutch Kit is designed to hold 100% to 200% torque capacity and provide you with a much-improved clutch engagement! The two ceramic disc setup provides additional contact surface areas to more evenly distribute pressure and heat for both a boost in performance and wear prevention. Kit Contents: Pressure Plate Two Ceramic 240mm Discs Steel Single-Mass Flywheel Pilot Bearing/Bushing and Throw-out Bearing (when applicable) Alignment Tool Rated for 100-200% increased torque over stock **Due to the nature of lightened single mass flywheels added "NVH" or "chatter" will or may occur during operation. Accompanying modifications can also increase or decrease the amount of "NVH" or "chatter" in the drivetrain. Please contact our sales team with any questions.**

Show More Show Less

Valeo Clutch Kit - 6-Speed Transmission - 21207625147

We Price Match - Give Us A Call or Chat!

T#:29002091

Part#: 21207625147

In Stock at Vendor

$ 429.03

This product was last offered at the strikethrough price on
07-14-2026

$ 429.00 USD

Add to Wish List

Qty

$ 429.00 USD

Add to Wish List

Slipping, chatter and difficulty shifting gears are signs that the clutch and pressure plate are worn down. Eventually, these symptoms can worsen, rendering your vehicle useless. The kit includes a new Valeo clutch disc, pressure plate, and throwout bearing. Replace these components, located in the transmission bell housing, to restore your car’s performance.

Show More Show Less

OS Giken Clutch Kit - STR Series - R52, R53

T#:54388380

Part#: MN021-BJ5

Ships in 2 Business Days

$ 1,920.00 USD

Add to Wish List

Qty

$ 1,920.00 USD

Add to Wish List

Upgrade your drivetrain and experience the perfect balance of track performance and street drivability.

R55/R56/R57 Clutch Kit - Priced As Set 52281201 832228

We Price Match - Give Us A Call or Chat!

T#:23416535

Part#: 21207572843

Ships on Aug 31, 2026

$ 323.99 USD

Add to Wish List

Qty

$ 323.99 USD

Add to Wish List

Restore your Mini to optimal performance with the MINI Clutch Kit, designed to address clutch slipping issues. If your Mini's clutch feels worn while the slave cylinder and pedal appear undamaged, this kit provides the essential components for a complete clutch replacement. It includes the clutch disc, pressure plate, and release bearing, ensuring a comprehensive solution to get your Mini back in working order.

Complete clutch replacement kit
Includes clutch disc, pressure plate, and release bearing
Restores clutch performance and functionality

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Performance Clutch Kits & Parts

Sub-Categories

Valeo Dual Mass Flywheel Conversion Kit for MINI Cooper S/JCW

MINI R52 R53 Clutch Kit For Solid Flywheel Conversion

JMTC MINI Cooper S Solid Flywheel Conversion Clutch Kit

Key Benefits:

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results