BMW Engine Parts

When your CPV O-ring fails it causes a slow oil leak on the passenger side of the engine, making an oily mess that frequently resembles a rear main seal leak. Replacing the CPV with an upgraded o-ring ensures a long-term solution to this common problem. 

The factory o-ring over time fails from heat cycling and oil exposure due to the Buna rubber used in OEM o-rings, while the included Viton Fluoroelastomer is resistant to a much higher temperature to ensure prolonged life without leaking. 

If you have ever attempted to do a valve job or cylinder head gasket project on an M42, M44, M50, or M52 engine you know that the repair manual will refer to the special BMW timing tool kit. This tool kit includes a flywheel locating lock pin, and a special set of camshaft locators that lock the cams in a precise location. The tools are very easy to install. The kit is specifically designed to hold the engine and cams in proper timing during the cylinder head removal and re installation process. This avoids the chance of bending the valves doing the head install process. The precision ground holding blocks lock over the square ends of both intake and exhaust cams. The CNC machined flywheel locating pin passes through a hole in the rear of the engine block and passed through a machined hole in the flywheel.

To avoid improper cam timing on the latest BMW engines, the factory has devised a cam timing system that locks the crankshaft and cams into a specific position prior to cylinder head removal. This method was devised to avoid any misalignment, resulting in piston to valve damage. Unfortunately without these tools re-timing the camshafts after a valve job is almost impossible. The factory specification manual does not supply installation specifications. This cam timing kit includes all the necessary components to do the job.

This item fits the following BMWs:
1990-1991 E30 BMW 318i 318is 318ic
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi

NOTE: Not compatible with S50B30 and S50B32 Euro engines!If you have ever attempted to do a valve job or cylinder head gasket project on an M42, M44, M50, or M52 engine you know that the repair manual will refer to the special BMW timing tool kit. This tool kit includes a flywheel locating lock pin, and a special set of camshaft locators that lock the cams in a precise location. The tools are very easy to install. The kit is specifically designed to hold the engine and cams in proper timing during the cylinder head removal and re installation process. This avoids the chance of bending the valves doing the head install process. The precision ground holding blocks lock over the square ends of both intake and exhaust cams. The CNC machined flywheel locating pin passes through a hole in the rear of the engine block and passed through a machined hole in the flywheel.

 

Every 60-80,000 miles, we recommend replacing your spark plugs to ensure your ignition system is running optimally. Over time carbon can build up around the head of the spark plug and decrease spark strength and effectiveness, leading to weaker fuel mixture detonation, misfires, and potential check engine lights. To prevent this, have put together our High-Performance Ignition Service Kits. These kits include new Bav Auto High-Performance Ignition Coils, new spark plugs, dielectric grease, and a BMW spark plug service label to keep track of when your spark plugs were replaced.

Bav Auto's Ignition coils feature core windings that have been modified to increase firepower and promote a faster, more efficient burn. This gives your BMW/MINI increased torque in the lower range of RPM and more horsepower in the upper range. Exact improvements depend on the current condition of your engine, but you'll definitely feel the difference. They'll also improve your fuel economy.

From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Ensure proper sealing when installing the turbos on your N54.

Kit includes:

• 16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

The BMW M60 and M62 engines found in many 5 series, 7 series, and X5's has two major weak points over time - Vanos seal and timing guides. The timing guides, being the most noticeable and damaging, can be very expensive to have a shop repair when trying to get back on the road. If you have some mechanic abilities and can follow instructions you could get this job done for a lot less, but you'll need the right tools for the job. 

This Schwaben kit features everything you need in one case to perform either job or both making timing service easy and accurate.

Never worry about buying another M60 or M62 timing tool kit again with our LIFETIME REPLACEMENT program - included with your purchase!

Tools included:

• Camshaft locking blocks
• Flywheel locking pin
• Timing chain tension block
• Upper chain tension locks
• Timing wheel alignment tools
• Vanos adjustment socket
• Vanos solenoid socket

Every 60-80,000 miles, we recommend replacing your spark plugs to ensure your ignition system is running optimally. Over time carbon can build up around the head of the spark plug and decrease spark strength and effectiveness, leading to weaker fuel mixture detonation, misfires, and potential check engine lights. To prevent this, have put together our High-Performance Ignition Service Kits. These kits include new Bav Auto High-Performance Ignition Coils, new spark plugs, dielectric grease, and a BMW spark plug service label to keep track of when your spark plugs were replaced.

Bav Auto's Ignition coils feature core windings that have been modified to increase firepower and promote a faster, more efficient burn. This gives your BMW/MINI increased torque in the lower range of RPM and more horsepower in the upper range. Exact improvements depend on the current condition of your engine, but you'll definitely feel the difference. They'll also improve your fuel economy.

From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

MINI R56 Ignition Coil Performance - Black - Pack of Four offers a direct plug-and-play upgrade, delivering up to 10% more energy output than the stock ignition coils. Designed for N12, N14, N16, and N18 engines, these high-performance coils enhance spark energy, resulting in improved throttle response, smoother engine operation, and better overall performance.

• Direct Plug-and-Play Upgrade: Easy installation with no modifications required.
• Increased Energy Output: Up to 10% more energy compared to stock coils.
• Enhanced Engine Performance: Improved throttle response and smoother operation.
• High Compatibility: Specifically designed for N12, N14, N16, and N18 engines.
• Durable Construction: Built to withstand the demands of high-performance driving.