MSD Performance Coil Pack for MINI

Before ordering, check whether you need round or flat pin connectors for your MINI's coil pack. The type of pin is determined by the connectors that link the coil to the wiring harness. To check, slide the red locking tab to the right, press down on the tab, and pull the connector off the coil. Examine the pins to see if they are flat or round. Reattach the connector by pushing it back on until it clicks, then slide the red locking tab back to the locked position.

This high-performance coil pack is a popular upgrade among MINI owners looking to enhance their vehicle's performance over the stock coil. The installation requires removing the factory bolts from the old coil and modifying the MSD factory sleeves by drilling out 1/16" to fit the stock bolts.

Kits Include:

• MSD Coil Pack
• MSD Wire Set - Red
• Inductance: 7mH
• Maximum Voltage: 36,000 Volts
• Primary Resistance: 0.51 OHMs
• Secondary Resistance: 12K OHMs
• Turns Ratio: 77:1

Key Benefits:

• Upgraded performance over stock coil pack
• Enhances ignition efficiency and engine performance
• High voltage output of 36,000 volts for stronger sparks
• Low primary resistance of 0.51 OHMs for efficient energy transfer
• High secondary resistance of 12K OHMs for improved performance
• Durable construction for long-lasting use

JMTC Super S F56 Turbocharger for MINI

For MINI enthusiasts seeking a powerful upgrade, the JMTC Super S F56 turbocharger is engineered for both street and track performance. Designed with a 50mm compressor and a 9-blade high-flow turbine, this turbocharger offers rapid boost and significant power gains at higher RPMs. It maintains the quick response of the original turbo while delivering increased torque and horsepower.

Key Benefits:

• Billet Compressor: Ensures high durability and performance.
• High Flow 9-Blade Lightened Turbine: Provides quick spooling and efficient power delivery.
• High Strength Internals: Designed to withstand higher pressures.
• Upgraded 360-Degree Bearing: Enhances reliability and performance.
• High-Temperature Alloy Turbine Housing: Resists heat for consistent performance.
• Water-Cooled Bearing Housing: Improves cooling and longevity.
• Quick Spooling Dual Scrolling Housing: Reduces lag and enhances responsiveness.
• Power Increase: Up to 300 BHP for Cooper S and 320 BHP for JCW with supporting mods and ECU tuning.

Important Notes:

• The turbocharger does not include an electric actuator; use the one from your old turbo.
• For optimal results, consider refurbishing your OEM catalytic converter or using a high-flow downpipe. Installing a new oil line is also recommended to prevent future issues.
• Turbocharger rebuilds include a complete overhaul and replacement of any worn or damaged components, with a full warranty on rebuilt parts.

Ferrea valve springs are developed from high strength alloys, including premium grade chrome silicone steel These springs are manufactured with state-of-the-art equipment. Ferrea springs are heat-treated and stress-relieved, which dramatically increases the spring's life. Strict quality control procedures and cycle testing ensures consistency from batch to batch. Ferrea valve springs provide the stability needed for high lift, high rpm racing and street car engines. Kit includes a set of 24 springs. MUST be used with the Ferrea Spring Seat and Titanium Retainers. See links below. 

https://www.turnermotorsport.com/e/p-163-e36-325-328-m3-ferrea-spring-seat-set/ 

https://www.turnermotorsport.com/e/p-31-e36-325-328-m3-ferrea-titanium-retainer-set/

This item fits the following BMWs:
1992-1998 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1991-1995 E34 BMW 525i

MINI R55 to R59 JMTC MCS Refurbished Turbocharger N18

The MINI R55 to R59 JMTC MCS Refurbished Turbocharger N18 offers exceptional performance with its high-flow twin-scroll turbine and extended tip compressor. This turbocharger enhances boost response, delivering significant torque and power gains across the entire power band. Designed for early spool-up and sustained high RPM performance, it achieves optimal results when paired with an aftermarket exhaust system.

• High-flow twin-scroll turbine for superior performance
• Extended tip compressor wheel for improved boost and response
• High-temperature alloy turbine housing for durability
• Water-cooled bearing housing for enhanced cooling
• Includes $100 core charge, refundable upon core return

Additional Information:

• MCS OEM/Interchange Part Numbers: 53039880163, 53039880118, 53039700163, 53039880181, 53039700181, 53039880118, 53039700118, 53039710163
• Product video available

Notes:

• New oil supply line recommended for optimal performance
• Optional refurbished catalytic converter available for extended 2-year warranty
• Refurbished parts may show signs of previous use, including scratches or imperfections
• CNC work done before porting; exact port matching within 100 microns cannot be guaranteed

The JMTCs S45 F56 turbocharger was designed with the street and track enthusiast in mind. We started with our huge 50mm compressor and upgraded quick spool high flow turbine to give you full boost quick and a huge amount of power at the top end. We also designed it to maintain the quick response of the original turbo but deliver much more torque and power.

This turbocharger not only delivers high torque in the low to mid-range but you will also see a power increase at higher RPM. No torque or power loss like you see with the original small 43mm turbo. If you are looking for a great street, track, or strip upgrade that delivers full race performance this is the turbo for you. Don’t be left at the starting line by any other car and get one our S45 turbos today.

S45 Specs

• 50/67mm Billet High flow compressor
• Quick Spooling 45/40mm High Flow exhaust turbine
• High strength internals with 360deg bearing
• Designed for higher pressure and high temperature turbine housing
• Water cooled bearing housing and quick spooling dual scrolling housing
• New electronic wastegate actuator (new turbo only, DV/BOV not included)

Requirements

• 3" full exhaust (to increase life of the turbo and the engine)
• ECU tuning (to increase preset power due to ECU load limits) - Please contact JM Turbo Cooper for local and regional tuners that require a custom tune for it to perform. JM Turbo Cooper
• One step colder spark plugs
• New oil supply line (to increase life of the turbo)

For engine and turbocharger reliability reasons JMTC requires a 3" or larger exhaust (from turbo to exhaust tip, no exceptions). As well as installing a new oil line and one step colder spark plugs. Tuning is not required but will be will help the turbo and engine reach their full potential. Price Includes the core charge of $250 that will be refunded when a rebuttable core is returned to JMTC. Refurbished turbos do not come with a wastegate actuator or one that has not been tested.

JMTC S42 Turbocharger MINI Cooper Upgraded Turbo K03 - Refurbished

Explore the JMTC S42 Turbocharger MINI Cooper Upgraded Turbo K03 - Refurbished, crafted for MINI Cooper enthusiasts seeking enhanced performance and power gains.

• Upgraded 42mm Compressor: Delivers early spool and sustained boost for enhanced performance.
• High Flow Exhaust Turbine: Lightened design for improved exhaust flow.
• Enhanced Durability: Upgraded with K04 internals and a 360-degree bearing for reliability under high pressure.
• Dual Scrolling Turbine Housing: Provides optimal airflow and efficiency.
• Water-cooled Bearing Housing: Maintains bearing integrity under high temperatures.
• OEM and Aftermarket Compatibility: Fits OEM and aftermarket intakes with minor modifications for optimal fitment.

Upgrade your MINI Cooper with the JMTC S42 Turbocharger for uncompromising performance and power.

Please contact JM Turbo Cooper for local and regional tuners requiring custom tunes.

MINI N14 JMTC MCS Refurbished Turbocharger is designed to enhance the performance of your MINI Cooper S with significant power and torque gains. This high-flow, twin-scrolling turbocharger features an extended tip compressor for early and sustained boost, making it ideal for enthusiasts seeking superior engine response and power across the entire RPM range.

• Enhanced Performance: Delivers outstanding torque and power throughout the RPM band.
• Early Spool: Boost starts early and continues into higher RPMs.
• Durable Design: Includes high-temperature alloy turbine housing and water-cooled bearing housing.
• Twin Scroll Turbo: Provides improved response and efficiency.
• Extended Tip Compressor Wheel: Optimizes airflow and performance.

Additional Information:

• Core Charge: Includes a $100 core charge, refundable upon return of the core turbo.
• Compatibility: Fits MCS OEM/Interchange models 53039880163, 53039880118, 53039700163, 53039880181, 53039700181, 53039880118, 53039700118, 53039710163; JCW OEM/Interchange 53039880146.
• Installation Recommendations: Consider installing a new oil supply line and a new or refurbished catalytic converter for optimal performance. A two-year warranty is extended when ordered together.
• Refurbishment Note: This part is refurbished and may have imperfections such as scratches or dents. For a flawless appearance, consider new parts instead.

MINI F54 to F57 JMTC B38/B36 Refurbished Turbocharger

The MINI F54 to F57 JMTC B38/B36 Refurbished Turbocharger features a high-flow twin-scroll turbine and an extended tip compressor, designed to deliver early and sustained boost. This turbocharger enhances torque and power across the entire power band, providing excellent response and performance throughout the RPM range. For optimal results, pairing this turbo with an aftermarket exhaust system is recommended to fully realize its potential.

• High-flow twin-scroll turbine for improved performance
• Extended tip compressor wheel for early spool-up and sustained boost
• High-temperature alloy turbine housing for durability
• Water-cooled bearing housing for enhanced cooling
• Includes a $200 core charge, refundable upon core return

Additional Information:

• New oil supply line recommended for best performance
• Optional refurbished catalytic converter available to extend the warranty to 2 years when ordered together
• Refurbished parts may exhibit signs of previous use, such as scratches or imperfections
• CNC work done before porting; exact port matching within 100 microns cannot be guaranteed due to extrude porting removing material from internal surfaces