This is a common failure item which can cause a check engine light, and rough engine running on the M52/S52 engines (328, M3, 528 thru 98, Z3 2.8, & M Roadster/Coupe thru 2000). If you have received an engine fault code suggesting "cam shaft reference sensor" or similar, this is most likely the cuprit. Once replaced, you will need to clear the fault code. We recommend replacing the cam position sensor o-ring at the same time.

OEM VDO is one of the largest OE providers in the world, supplying numerous vehicle brands, including BMW, with many of their genuine parts that build the vehicle before they ever reach the car lot. Entrusted by many of the top names in automotives and with their proven history of reliability, it makes all of us here at Turner confident that their line of OEM replacement parts are a perfect option to restore your vehicles original operation and performance. The same great quality or higher than Genuine BMW parts at a lower cost.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform

Restore your fuel systems operation with this high quality OEM VDO fuel pump. This fuel pump fits the BMW E46 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci from 1999-2005. This fuel pump is located inside the fuel tank on the right side. Manufactured by VDO. Note not for 325i 325ci with M56 SULEV engine 2003-2006.

Replacement for BMW part # 16146766942, 16141184276, and 16146752499.

OEM VDO is one of the largest OE providers in the world, supplying numerous vehicle brands, including BMW, with many of their genuine parts that build the vehicle before they ever reach the car lot. Entrusted by many of the top names in automotives and with their proven history of reliability, it makes all of us here at Turner confident that their line of OEM replacement parts are a perfect option to restore your vehicles original operation and performance. The same great quality or higher than Genuine BMW parts at a lower cost.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
1999-2005 E46 BMW 323i 323ci 328i 328ci 330i 330ci 330xi
2001-2005 E46 BMW 325i 325ci 325xi with M54 engine

Decreased performance, lower fuel economy and smoke coming from the exhaust could point to failing fuel injectors. Restore your vehicles fuel system back to top shape with OEM VDO fuel injectors.

OEM replacement for BMW part # 13647525721 and 13537506924.

OEM VDO is one of the largest OE providers in the world, supplying numerous vehicle brands, including BMW, with many of their genuine parts that build the vehicle before they ever reach the car lot. Entrusted by many of the top names in automotives and with their proven history of reliability, it makes all of us here at Turner confident that their line of OEM replacement parts are a perfect option to restore your vehicles original operation and performance. The same great quality or higher than Genuine BMW parts at a lower cost.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Genuine MINI Rubber Bushing - 11617593928

Explore the Genuine MINI Rubber Bushing - 11617593928, designed to optimize your Mini's performance. This essential rubber mount bushing, situated on the intake manifold and intake box, efficiently connects the intake system while minimizing vibrations.

Benefits:

• Enhances intake system connectivity
• Reduces vibrations for smoother operation
• Ensures durability and longevity

Upgrade your Mini's performance with the Genuine MINI Rubber Bushing - 11617593928.

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent.  The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories.  These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

Fits the following BMWs:
2000-2006 E46 BMW 323/325/328/330

This Siemens VDO Eccentric Shaft Sensor for the Valvetronic valve timing system on BMW N62,N73, and N62N engines. This sensor is mounted on the rear of the engine near the firewall. Sold individually.

OEM VDO is one of the largest OE providers in the world, supplying numerous vehicle brands, including BMW, with many of their genuine parts that build the vehicle before they ever reach the car lot. Entrusted by many of the top names in automotives and with their proven history of reliability, it makes all of us here at Turner confident that their line of OEM replacement parts are a perfect option to restore your vehicles original operation and performance. The same great quality or higher than Genuine BMW parts at a lower cost.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform

This item fits the following BMWs:
2004-2010 E60 BMW 545i 550i
2004-2010 E63 BMW 645ci 650i
2002-2008 E65 BMW 745i 745li 750i 750li 760i 760li
2004-2006 E53 BMW X5 4.4i X5 4.8is
2007-2010 E70 BMW X5 4.8i X5 xDrive48i

R55-R59 Oil Catch Can Kit for N18 MINI Engines

Introducing the newly updated R55 through R59 Oil Catch Can kit for MINIs equipped with the N16 or N18 engine. This kit includes a "designed-to-fit" stainless steel bracket, mounting hardware, and pre-assembled hoses for easy installation—no drilling or special tools needed. Note: This kit has been redesigned to fit directly behind the outlet of the airbox on the firewall, using the factory tab located on the firewall.

Despite skepticism from "forum experts and social hysteria," an Oil Catch Can (OCC) is essential. Many MINI owners suffer from carbon buildup on their intake valve due to oil being recycled through the intake tract. With the M7 Oil Catch Can, your MINI Cooper's engine will be protected from excessive oil and hydrocarbon buildup, preventing performance-hindering oil film and sludge. Direct injection in 2007 & up MINIs exacerbates the issue, leading to oil blow-by burning onto intake valves, resulting in power loss and expensive repairs.

By capturing excess oil vapor and particles, the M7 Oil Catch Can ensures optimal engine performance. Now with our exclusive "Exact-Fit" pre-assembled hose kit and brackets, installation is super easy.

Features:

• Pre-assembled hose assemblies
• Stainless steel bracket and mounting hardware
• Eliminates intake tract oil contamination and intake valve damage
• Prevents premature sensor failure
• Maintains engine performance at peak levels
• Carbon Fiber canister with billet bright aluminum top and bottom

The M7 Oil Catch Can is not only functional but also a work of automotive performance ART! It features a 100% carbon fiber housing with CNC machined billet aluminum top and bottom, adding a sharp look to your engine compartment.

All hoses, brackets, clamps, necessary fittings, and easy-to-follow detailed step-by-step instructions are included, along with an oil drain plug and an easy-to-view sight tube. The sight tube allows you to monitor the oil level in the can. The hoses are high-quality "Made in the USA" automotive grade, designed to withstand the rigors of the under-hood environment without degradation.

• main drive belt, 11281706545
• A/C belt, 11281437450
• mechanical belt tensioner with pulley, 11281427252
• A/C belt tensioner with pulley, 11287512758
• deflection pulley, 11281748130
• mounting bolts

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent.  The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories.  These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

This part fits the following BMW engines:
S54

This part fits the following chassis:
E46, Z3, Z4