BMW S65 4.0L Vanos Covers 7075 provide a robust replacement for the factory plastic covers, which are known to fail over time. These high-performance Vanos covers snap on securely, offering a precise fit to eliminate vibration and prevent chafing of the engagement dogs.

• High-Strength Construction: Machined from premium 7075 aluminum for superior durability and strength.
• Corrosion Resistance: Anodized finish ensures long-lasting protection against corrosion.
• Perfect Fitment: Designed for an exact fit to avoid issues such as vibration and chafing.
• No Timing Tools Required: Easy installation with no need for engine timing tools.

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve 

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
 ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

If you're experiencing hard starting, flaky charging, or other electrical issues, your engine ground strap may be the culprit. On E9X BMWs, the engine ground strap is a thin, non-insulated cable that spans from the left engine mount arm to the frame horn. Despite the seemingly simple nature of this part, on older cars, it is known to cause massive headaches. Due to its non-insulated design, years of exposure to water, dirt, and road salt will cause the wire to corrode, ultimately leading to complete failure. A break in this cable will cause an open circuit, resulting in issues with the vehicle's electrical system and potentially leading to a no-start condition.

To solve this issue, ECS has engineered an exact-fit, upgraded ground strap for your E9X BMW! Unlike its OEM counterpart, this design features insulated, large-gauge copper wire for dependable conductivity and long-lasting durability. Additionally, factory-style lugs are zinc-coated, crimped, and soldered, ensuring protection against corrosion and oxidation.

Whether you're replacing a visibly corroded strap or proactively preventing failure, this solution from ECS is sure to provide lasting performance and protection.

FEATURES

Direct-fit replacement and upgrade for RWD E82/E88, E84, and E9X applications Solves intermittent grounding issues caused by aging OEM straps Clean, stealthy design that fits seamlessly in factory engine bays Factory length and lug orientation for drop-in fitment 2 AWG tinned copper cable for excellent conductivity and corrosion resistance Zinc-coated lugs, crimped and soldered to resist moisture and oxidation Black UL1015-grade insulation withstands oil, heat, and abrasion Discreet ECS label for a clean, OEM+ look Replaces OEM part numbers 12427549393, 12427795404, and 12427790559.

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice. 

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

• 1x Aluminum Crank Bolt Capture
• 8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54 

If you're experiencing hard starting, flaky charging, or other electrical issues, your engine ground strap may be the culprit. On E9X BMWs, the engine ground strap is a thin, non-insulated cable that spans from the left engine mount arm to the frame horn. Despite the seemingly simple nature of this part, on older cars, it is known to cause massive headaches. Due to its non-insulated design, years of exposure to water, dirt, and road salt will cause the wire to corrode, ultimately leading to complete failure. A break in this cable will cause an open circuit, resulting in issues with the vehicle's electrical system and potentially leading to a no-start condition.

To solve this issue, ECS has engineered an exact-fit, upgraded ground strap for your E9X BMW! Unlike its OEM counterpart, this design features insulated, large-gauge copper wire for dependable conductivity and long-lasting durability. Additionally, factory-style lugs are zinc-coated, crimped, and soldered, ensuring protection against corrosion and oxidation.

Whether you're replacing a visibly corroded strap or proactively preventing failure, this solution from ECS is sure to provide lasting performance and protection.

FEATURES

Direct-fit replacement and upgrade for RWD E82/E88, E84, and E9X applications Solves intermittent grounding issues caused by aging OEM straps Clean, stealthy design that fits seamlessly in factory engine bays Factory length and lug orientation for drop-in fitment 2 AWG tinned copper cable for excellent conductivity and corrosion resistance Zinc-coated lugs, crimped and soldered to resist moisture and oxidation Black UL1015-grade insulation withstands oil, heat, and abrasion Discreet ECS label for a clean, OEM+ look Replaces OEM part number 12427549396.

These WPC-treated bearings are the best we have seen! WPC is a shot-peening treatment at a microscopic level. It's perfect for sensitive surfaces like bearings. The WPC treatment removes imperfections and high spots, while creating a surface that retains oil better than the original surface. This greatly reduces friction. The bearings in this kit are original equipment KS bearings that are sent to WPC for treatment. The treated bearings are stronger with less metal fatigue and less friction than buying off-the-shelf bearings from the dealer.

This item fits the following BMWs: 
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is 325ix 
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
1982-1988 E28 BMW 528e
1989-1995 E34 BMW 525i
1997-2003 E39 BMW 525i 528i 530i
2004-2005 E60 BMW 525i 530i 
2004-2006 E83 BMW X3 2.5i X3 3.0i 
2000-2006 E53 BMW X5 3.0i 
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe 
2003-2005 Z4 BMW Z4 2.5i Z4 3.0i 

Vargas Turbo has done it again. They've made it even easier for you to get your car back on the road and running right again with your new turbos. They've put together an install kit containing all the components you need to get your new turbos installed properly and efficiently. This means you can get your car back on the road faster and enjoy your new turbos! 

Starting in 1978, Vargas Turbo Technologies was built upon the dream of utilizing then-new turbocharger technology to improve the performance of everything from cars to boats. On the cutting edge since the beginning, the company has grown with the industry, servicing diesel and industrial turbochargers. Returning to their hot-rod roots, Vargas has jumped head-first into the BMW performance market, filling a need for high-quality, cost effective turbocharger upgrades for everything from daily-driven street cars to all-out racing machines.

The main reason all of the VANOS units will eventually fail is because the material used for the sealing rings from the factory is not designed for that type of environment. When this happens the only option that BMW leaves you with is buying a new and expensive VANOS unit with the same sealing rings that failed in your original unit.

The VANOS system found in BMW engines is a great feature (when it’s working properly), keeping your power curve smooth and responsive especially in lower to mid RPM range. What usually goes unnoticed is the gradual loss of power within this range as the vehicle's age due to slowly failing seals within the VANOS unit. The way the VANOS system works is based off of oil pressure triggered by a solenoid that allows for a small range of timing degree adjustment, this is where the power curve is affected. When the seals begin to fail (all of them do) there is less pressure to advance the timing reducing the power in that low to mid range. Because this happens slowly it's very hard to notice a difference until you refresh your VANOS unit, then you easily realize the response you've been missing.

There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.

While you're replacing the seals in your VANOS unit it a good time to install anti-rattle spacers to tighten up the gaps in your stock assembly and get rid of that noisy VANOS clatter.

Seals & O-rings:

The seals  were the main focus of this project since the OE units are built with Buna-N rubber o-rings instead of the ECS supplied Viton rubber o-rings. The Buna-N material quickly hardens from the heat and chemical exposure within the engine, where the Viton is significantly more resistant to these chemicals. This knowledge was also used when it came to the commonly failed o-rings found on the VANOS seal plate, replaced at the solenoid.

Rattle Repair:

When it comes to the VANOS rattle this is commonly described as "marbles in a can", and can be heard throughout the different RPM ranges depending on the engine. These upgraded rings and washers are precision ground from hardened steel to resist wear and deformation keeping your VANOS rattle free. The rattle repair tools are designed specifically for this VANOS anti-rattle repair, design from hardened steel to stand up to the job. Designed to perfectly follow the splines of the shaft for a tight grip when applying the necessary torque to disassemble & reassemble the VANOS transfer gear. The keyed socket was designed with the intent to use a "common" wrench so this can be completed at home in your garage.    

When Servicing your VANOS unit we recommend getting everything you need to replace on the way to service which includes an oil change and valve cover gasket set. Fresh oil and gaskets is the best way to start off a fresh rebuild of any kind giving you the maximum performance of your freshly serviced components.

Don't forget to check out our rebuild PDF to make sure you have everything to get the job done and eliminate the rebuild guess work.

This item fits the following BMWs: 
2000-2001 E46 3 Series M3 M3 Convertible 2000-2006 
2001-2002 Z3 Roadster / Coupe Z3 M Roadster Z3 M Coupe w S54 Engine 
2006-2008 E86 E86 Z4 Z4 M Roadster Z4 M Coupe

BMW E39 M5 S62 ECS VANOS Seal Kit

Revitalize your BMW E39 M5 S62 engine with the ECS VANOS Seal Kit, designed to restore peak performance and eliminate common Vanos system issues. Over time, the original seals in the Vanos units can harden and wear, leading to reduced hydraulic pressure and compromised cam timing control. Symptoms such as cold start rattle, erratic idle, and decreased torque output are common indicators of failing seals. ECS Tuning offers a cost-effective solution with their precision-engineered seal kit, crafted to OEM standards for reliability and durability.

Key Benefits:

• Rebuilds Vanos units to eliminate performance issues
• Precision-engineered seals ensure optimal cam timing control
• DIY-friendly with detailed installation guide for professional results
• Includes bronze impregnated Teflon seals and 70A Viton backing o-ring for enhanced durability and chemical resistance

Our Vanos seals were engineered in-house and precision machined to exacting tolerances to restore the original performance of the Vanos units.

Bronze impregnated Teflon seal for durable dynamic sealing.
70A Viton backing o-ring for extended chemical resistance, removing the OE failure point.

Vargas Turbo has done it again. They've made it even easier for you to get your car back on the road and running right again with your new turbos. They've put together an install kit containing all the components you need to get your new turbos installed properly and efficiently. This means you can get your car back on the road faster and enjoy your new turbos! 

Starting in 1978, Vargas Turbo Technologies was built upon the dream of utilizing then-new turbocharger technology to improve the performance of everything from cars to boats. On the cutting edge since the beginning, the company has grown with the industry, servicing diesel and industrial turbochargers. Returning to their hot-rod roots, Vargas has jumped head-first into the BMW performance market, filling a need for high-quality, cost effective turbocharger upgrades for everything from daily-driven street cars to all-out racing machines.

Oil venting and circulation continues to be a problem on BMW engines and now even more so on the turbocharged N54 and N55 engines. The existing stock system does a very poor job of separating fluid and vapor and this leads to an oily film or even small pools of oil throughout the turbos and intake. We're seeing a lot more 135 and 335 cars with drivability and performance issues because oil has sneaked by the ring seals and is coating the intake piping, intercooler, intake valves, and other critical areas. The problem is worsened with higher boost levels. Oil is excellent for lubricating moving parts but terrible when it gets into the combustion chamber, effectively lowering the octane rating and reducing performance. Our own shop has gone the extra step and offers media blasting of the intake valves to strip away the oily buildup we have seen.

Our shop also strongly recommends an oil catch can be installed in the line for the crankcase vent. The oil catch can traps oil as it leaves the valve cover and holds it in a canister. This catch can is located on the cooler side of the engine where the oil will condense easier and stay in the can. Whatever minimal vapors are left over in the oil is then vented back through the canister and into the intake where it is safe to be burned up in the engine or recirculated back through the system again. This is the way the system was designed! At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil. The Burger Tuning oil catch can is the best we have seen so far. Installing one of these will avoid costly repairs in the future and help maintain your boost and performance. It's one of the smartest modifications you can make because it demonstrates a well-thought out tuning strategy and care for the condition of your engine.

The BMS Oil Catch Can is made from aluminum and with a stealthy black anodized finish. It installs on the cooler side of the engine with a dedicated bracket and new oversized vent lines. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). The BMS OCC also has a factory-like appearance. Since BMS designed their catch can from scratch they can guarantee it fits and performs correctly for the N54/N55 engine, unlike other catch cans on the market that are poorly retrofitted from other applications and under-sized for the N54 engine.

Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles

BMS Oil Catch Can Features:
+ Increases air intake efficiency
+ Promotes engine longevity
+ Double-baffled design allows excellent air/oil separation
+ Large In/Out ports (no tapered sizes that slow flow)
+ Stealth mounting on cooler side of engine bay (promotes condensation of oil to vapor)
+ Anodized black lightweight aluminum
+ N54 version mounts out of sight under the cowl
+ Made in USA with a lifetime guarantee

Upgrade your BMW S58 5.0L engine with the BMW S58 5.0L VANOS Solenoid O Ring Kit. This high-quality kit includes replacement O rings for the VANOS solenoids, ensuring proper sealing and preventing oil leaks. With easy installation and durable materials, this kit is essential for maintaining optimal performance and reliability of your BMW S58 engine.

• Includes replacement O rings for VANOS solenoids
• Ensures proper sealing and prevents oil leaks
• Easy installation process
• Durable materials for long-lasting performance