BMW S65 4.0L Vanos Covers 7075 provide a robust replacement for the factory plastic covers, which are known to fail over time. These high-performance Vanos covers snap on securely, offering a precise fit to eliminate vibration and prevent chafing of the engagement dogs.

• High-Strength Construction: Machined from premium 7075 aluminum for superior durability and strength.
• Corrosion Resistance: Anodized finish ensures long-lasting protection against corrosion.
• Perfect Fitment: Designed for an exact fit to avoid issues such as vibration and chafing.
• No Timing Tools Required: Easy installation with no need for engine timing tools.

The N54 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load. This is most apparent under high-rev downshifts or in the case of increased boost pressure which creates more stress on the engines rotating assembly. In order to keep this from happening, the crank bolt must be secured to the hub to keep it from backing off, but this can be a tricky solution since a simple dab of Loctite will not suffice. 

Here is an easy, and cost-effective way to secure the situation; The VTT N54 crank bolt capture. This lightweight and durable ring slips over the head of the crank bolt fully encapsulating it, and locks it to the crank hub and eliminating its ability to spin. The VTT-CBC is 100% Billet Aircraft Grade Aluminum, Anodized black to protect it from the elements, and give it a stealth look. What's more is that it weighs only 1.3 Oz's meaning you aren't adding excess mass to the crankshaft which will avoid any imbalance or vibration issues.

While this is not a full fix for all crank hub spinning issues, the engineers at Vargas have found most issues have stemmed from the bolt itself backing out, and this is a great way to keep that from happening. Extremely lightweight at only 1.3 Oz's it adds virtually no weight to the crank which is important for balance and vibration.

Kit Includes:

• 1x Aluminum Crank Bolt Capture
• 8x Fasteners Gr. 12.9

This part fits the following BMWs:
2006-2013 N54 

Vargas Turbo has done it again. They've made it even easier for you to get your car back on the road and running right again with your new turbos. They've put together an install kit containing all the components you need to get your new turbos installed properly and efficiently. This means you can get your car back on the road faster and enjoy your new turbos! 

Starting in 1978, Vargas Turbo Technologies was built upon the dream of utilizing then-new turbocharger technology to improve the performance of everything from cars to boats. On the cutting edge since the beginning, the company has grown with the industry, servicing diesel and industrial turbochargers. Returning to their hot-rod roots, Vargas has jumped head-first into the BMW performance market, filling a need for high-quality, cost effective turbocharger upgrades for everything from daily-driven street cars to all-out racing machines.

Vargas Turbo has done it again. They've made it even easier for you to get your car back on the road and running right again with your new turbos. They've put together an install kit containing all the components you need to get your new turbos installed properly and efficiently. This means you can get your car back on the road faster and enjoy your new turbos! 

Starting in 1978, Vargas Turbo Technologies was built upon the dream of utilizing then-new turbocharger technology to improve the performance of everything from cars to boats. On the cutting edge since the beginning, the company has grown with the industry, servicing diesel and industrial turbochargers. Returning to their hot-rod roots, Vargas has jumped head-first into the BMW performance market, filling a need for high-quality, cost effective turbocharger upgrades for everything from daily-driven street cars to all-out racing machines.

Upgrade your MINI with the M7 Oil Catch Can Kit__xxSTARTxx__/h1

The newly updated R55 through R57 Oil Catch Can kit for MINIs equipped with the N14 engine comes with a "designed-to-fit" stainless steel bracket, mounting hardware and pre-assembled hoses. Installation is super easy...no drilling and no special tools are needed. NOTE: This kit has been redesigned to fit on the firewall directly behind the outlet of the airbox. It uses the factory tab located on the firewall."Forum experts and social hysteria" say an OCC is not needed but we beg to differ. Why do so many MINI owners suffer from carbon buildup on their intake valve? The answer is oil being recycled through the intake tract to be burned. With the M7 Oil Catch Can, your MINI Cooper's engine will be protected from excessive oil and hydrocarbon buildup which leads to performance-hindering oil film and sludge along your intake tract, on your engine control sensors and on your engine's intake valves. Because the 2007 & up MINI is direct injection the intake valves do not benefit from the cleaning action provided by the gasoline as in older port injection engines. Now all the oil blow-by burns onto the intake valves and builds up into a flow choking hydrocarbon mess. The end result is loss of power and a very expensive repair bill. This oil film & sludge can appear in other critical places throughout the engine-- such as the intercooler-- where clean surfaces are critical for maximized heat transfer and on your MAF sensor (Mass Air Flow) where the film will cause the sensor to send a false signal to your ECU killing performance.

By capturing excess oil vapor and particles, the M7 Oil Catch Can ensures that oil film and sludge will not become a factor in your vehicle's performance. If you don't think your engine is pumping oil back through your intake system, remove the breather tube and look at all the oil!. The breather tube connects directly to you intake hose and directs this oily mess back through your engine to be burned.

Now with our exclusive "Exact-Fit" pre-assembled hose kit and brackets installation is super-easy.

Features:

• Pre-assembled hose assemblies.
• Stainless steel bracket and mounting hardware
• Eliminate intake tract oil contamination and intake valve damage.
• Prevent pre-mature sensor failure
• Keep engine performance at peak levels
• Billet Aluminum Construction
• Bright Black Anodized Finish
• Laser Etched M7 Logo

The M7 Oil Catch Can is not only functional is a work of automotive performance ART! It is CNC machined from billet aluminum and adds a sharp look to your engine compartment.

All hoses, brackets, clamps, necessary fittings and easy to follow detailed step-by-step instructions are available on this page in .PDF format. The design includes an oil drain plug and an easy to view sight tube which indicated the oil level within the can. The hoses are high quality "Made in the USA" automotive grade designed to withstand the rigors of the under-hood environment and to not degrade when exposed to oil. Beware of other "low cost" catch can systems that use silicone hoses because oil and silicone are not compatible. Silicone hoses will will eventually deteriorate and make an absolute mess of your engine compartment.

R55-R59 Oil Catch Can Kit for N18 MINI Engines

Introducing the newly updated R55 through R59 Oil Catch Can kit for MINIs equipped with the N16 or N18 engine. This kit includes a "designed-to-fit" stainless steel bracket, mounting hardware, and pre-assembled hoses for easy installation—no drilling or special tools needed. Note: This kit has been redesigned to fit directly behind the outlet of the airbox on the firewall, using the factory tab located on the firewall.

Despite skepticism from "forum experts and social hysteria," an Oil Catch Can (OCC) is essential. Many MINI owners suffer from carbon buildup on their intake valve due to oil being recycled through the intake tract. With the M7 Oil Catch Can, your MINI Cooper's engine will be protected from excessive oil and hydrocarbon buildup, preventing performance-hindering oil film and sludge. Direct injection in 2007 & up MINIs exacerbates the issue, leading to oil blow-by burning onto intake valves, resulting in power loss and expensive repairs.

By capturing excess oil vapor and particles, the M7 Oil Catch Can ensures optimal engine performance. Now with our exclusive "Exact-Fit" pre-assembled hose kit and brackets, installation is super easy.

Features:

• Pre-assembled hose assemblies
• Stainless steel bracket and mounting hardware
• Eliminates intake tract oil contamination and intake valve damage
• Prevents premature sensor failure
• Maintains engine performance at peak levels
• Carbon Fiber canister with billet bright aluminum top and bottom

The M7 Oil Catch Can is not only functional but also a work of automotive performance ART! It features a 100% carbon fiber housing with CNC machined billet aluminum top and bottom, adding a sharp look to your engine compartment.

All hoses, brackets, clamps, necessary fittings, and easy-to-follow detailed step-by-step instructions are included, along with an oil drain plug and an easy-to-view sight tube. The sight tube allows you to monitor the oil level in the can. The hoses are high-quality "Made in the USA" automotive grade, designed to withstand the rigors of the under-hood environment without degradation.