Ensure optimal engine performance in your BMW M50 M52 Engines with Turner Motorsport's Mahle Piston Ring Set. Over time, worn piston rings can lead to power loss, increased oil consumption, and white smoke from the tailpipe. When rebuilding your BMW's engine, replacing the piston rings is essential for restoring power and efficiency. Each set is priced individually, with six sets required for complete engine overhaul.

Key Benefits:

• Restores engine power and efficiency
• Reduces oil consumption
• Prevents white smoke from the tailpipe
• Compatible with M50 M52 Engines

This is an OEM MAHLE fuel filter that removes dirt and other particle contaminants from your fuel.

A clogged fuel filter makes it difficult for your engine to get all the fueling it needs. Filters commonly clog from a deteriorating gas tank, bad fuel, or other debris in the fuel system. A fresh fuel filter addresses many fuel related problems including surging, stalling, cold start issues, and poor performance under a variety of conditions.

Stock-Size Piston Ring Set for Engine Head Repair

When it comes to engine head repair or rebuilding, this piston ring set is the perfect choice. Designed to be of stock size, it ensures a precise fit and reliable performance.

Key Details:

• One set of piston rings is needed for each piston.
• If your engine head contains four pistons, you'll require four sets to complete the repair.

This is an OEM MAHLE fuel filter that removes dirt and other particle contaminants from your fuel.

A clogged fuel filter makes it difficult for your engine to get all the fueling it needs. Filters commonly clog from a deteriorating gas tank, bad fuel, or other debris in the fuel system. A fresh fuel filter addresses many fuel related problems including surging, stalling, cold start issues, and poor performance under a variety of conditions.

This is an OEM Mahle oil filter replacement oil filter kit for vehicles with the N63 & N74 engines. The oil filter prevents contaminants from reaching the engine and causing premature failure. Replace your filter at all recommended service intervals to ensure a long engine life.

Replacement for Genuine BMW part # 11427583220.

This is an OEM MAHLE fuel filter that removes dirt and other particle contaminants from your fuel.

A clogged fuel filter makes it difficult for your engine to get all the fueling it needs. Filters commonly clog from a deteriorating gas tank, bad fuel, or other debris in the fuel system. A fresh fuel filter addresses many fuel related problems including surging, stalling, cold start issues, and poor performance under a variety of conditions.

BMW Supercharger Kits can be found all over the internet, but who should you choose to go with? If you want to go to with a forced induction system and want reliability and a driving feel that isn't adversely affected, the VF Engineering Supercharger Kit is one of the best options on the market. Included with every supercharger system is their custom proprietary VF.GIAC software that safely realigns all fueling and engine management parameters for optimal performance and long term drivability. Unlike many other options that are available, the VF Supercharger kit is designed to work with BMW's OEM parameters to minimize the likelihood of DTCs (Diagnostic Trouble Codes) and Check Engine Lights.

This 6.0 psi VF Engineering supercharger system is designed for simple bolt-on installation, remains fully OBD2 compliant, and can be installed in a single day, ready to run in approximately 8 hours. This kit is also non-intrusive and is fully reversible. 

The 6.0 psi manifold at peak boost was tested to be the optimal induction charge limit without aftercooling and offers max tourqe gains!

Upon ordering, you will be required to send your VIN number, ECU, and transmission type (auto or manual) to VF Engineering within 1 year of purchase for your software flash of the ECU.

This product is supported by a 1 year unlimited mileage warranty on the product only.

Rally Road Productions, Inc. is a team supported by a group of people with great abilities in their area of expertise. From the "web guy" and driving instructor friends, to owners of various machine shops, they have surrounded ourselves with people that can be trusted to create and manufacture quality products. This is the key to ensuring everything that they sell will perform as it was intended. The goal is to increase customer satisfaction and make the customization or performance enhancement of your vehicle a more enjoyable venture.

This oil cooler system is race tested and proven to outflow the euro M3 oil filter housing. Additionally, this particular system uses a sealing mechanism to direct the oil flow through the cooler lines and then through the oil filter.  Other cooler caps do not provide this seal and therefore the external oil coolers and lines act as a "balloon".  The lines and cooler are pressurized, but oil does not flow through them.  Flowing oil means it is being cooled and not just acting as an external reservoir.

Flow testing reveals that the oil cooler cap will outflow the Euro M3 Oil Filter Housing by more than 80% at the same, pressure, RPM, and oil temperature. In the upper RPM range, there is nearly a 100% improvement in flow from the RallyRoad oil cooler cap when compared to the Euro M3 oil filter housing.  This is a massive improvement over OE and is a worthwhile upgrade, especially in engines that see severe duty.

Features:

• -8AN o-ring ports to provide a leak free fitting without the use of Teflon tape or sealant used by other oil cooler caps.
• Viton o-rings are used throughout to maintain function and sealing in a high-temperature oil environment.
• Use of the stock filter cap bolt to reduce cost and simplify installation.
• An internal sealing mechanism to direct oil flow through the oil cooler and through the filter.
• 1/8" NPT side port for external oil pressure gauge.

Kit Includes:

• Oil filter cap with fittings
• Oil filter sealing ring
• BMW MANN Oil Filter and gasket

This part fits the following BMWs
1992-1999 E36 323i 325i 325is 328i 328is

Rally Road Productions, Inc. is a team supported by a group of people with great abilities in their area of expertise. From the "web guy" and driving instructor friends, to owners of various machine shops, they have surrounded ourselves with people that can be trusted to create and manufacture quality products. This is the key to ensuring everything that they sell will perform as it was intended. The goal is to increase customer satisfaction and make the customization or performance enhancement of your vehicle a more enjoyable venture.

Anyone that has approached the subject of substituting a higher volume fuel pump knows that fitting said pump into a stock housing can be a hassle. What's more is that certain methods can lead to less than safe or reliable results. Enter the Rally Road fuel pump adapter sleeve. This simple adapter makes the installation of a Walbro or Aeromotive fuel pump into the factory sending unit safe, secure and completely functional. The pump rests on a ledge at the bottom of the sleeve and is held tightly in the bracket by a mil-spec stainless steel clamp. A well thought, quality built solution to a common retrofit problem. 

Fits Walbro 450lph high volume fuel pumps.

This kit includes:

• Anodized fuel pump sleeve
• Stainless steel mil-spec hose clamp

This part fits the following BMWs
1992-1999 E36 323i 325i 325is 328i 328is

BMW Supercharger Kits can be found all over the internet, but who should you choose to go with? If you want to go to with a forced induction system and want reliability and a driving feel that isn't adversely affected, the VF Engineering Supercharger Kit is one of the best options on the market. Included with every supercharger system is their custom proprietary VF.GIAC software that safely realigns all fueling and engine management parameters for optimal performance and long term drivability. Unlike many other options that are available, the VF Supercharger kit is designed to work with BMW's OEM parameters to minimize the likelihood of DTCs (Diagnostic Trouble Codes) and Check Engine Lights.

This 6.0 psi VF Engineering supercharger system is designed for simple bolt-on installation, remains fully OBD2 compliant, and can be installed in a single day, ready to run in approximately 8 hours. This kit is also non-intrusive and is fully reversible. 

The 6.0 psi manifold at peak boost was tested to be the optimal induction charge limit without aftercooling and offers max tourqe gains!

Upon ordering, you will be required to send your VIN number, ECU, and transmission type (auto or manual) to VF Engineering within 1 year of purchase for your software flash of the ECU.

This product is supported by a 1 year unlimited mileage warranty on the product only.