Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent. The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories. These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.
Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.
Fits the following BMWs:
2000-2006 E46 BMW 323/325/328/330
The newly updated R55 through R57 Oil Catch Can kit for MINIs equipped with the N14 engine comes with a "designed-to-fit" stainless steel bracket, mounting hardware and pre-assembled hoses. Installation is super easy...no drilling and no special tools are needed. NOTE: This kit has been redesigned to fit on the firewall directly behind the outlet of the airbox. It uses the factory tab located on the firewall."Forum experts and social hysteria" say an OCC is not needed but we beg to differ. Why do so many MINI owners suffer from carbon buildup on their intake valve? The answer is oil being recycled through the intake tract to be burned. With the M7 Oil Catch Can, your MINI Cooper's engine will be protected from excessive oil and hydrocarbon buildup which leads to performance-hindering oil film and sludge along your intake tract, on your engine control sensors and on your engine's intake valves. Because the 2007 & up MINI is direct injection the intake valves do not benefit from the cleaning action provided by the gasoline as in older port injection engines. Now all the oil blow-by burns onto the intake valves and builds up into a flow choking hydrocarbon mess. The end result is loss of power and a very expensive repair bill. This oil film & sludge can appear in other critical places throughout the engine-- such as the intercooler-- where clean surfaces are critical for maximized heat transfer and on your MAF sensor (Mass Air Flow) where the film will cause the sensor to send a false signal to your ECU killing performance.
By capturing excess oil vapor and particles, the M7 Oil Catch Can ensures that oil film and sludge will not become a factor in your vehicle's performance. If you don't think your engine is pumping oil back through your intake system, remove the breather tube and look at all the oil!. The breather tube connects directly to you intake hose and directs this oily mess back through your engine to be burned.
Now with our exclusive "Exact-Fit" pre-assembled hose kit and brackets installation is super-easy.
The M7 Oil Catch Can is not only functional is a work of automotive performance ART! It is CNC machined from billet aluminum and adds a sharp look to your engine compartment.
All hoses, brackets, clamps, necessary fittings and easy to follow detailed step-by-step instructions are available on this page in .PDF format. The design includes an oil drain plug and an easy to view sight tube which indicated the oil level within the can. The hoses are high quality "Made in the USA" automotive grade designed to withstand the rigors of the under-hood environment and to not degrade when exposed to oil. Beware of other "low cost" catch can systems that use silicone hoses because oil and silicone are not compatible. Silicone hoses will will eventually deteriorate and make an absolute mess of your engine compartment.
Introducing the newly updated R55 through R59 Oil Catch Can kit for MINIs equipped with the N16 or N18 engine. This kit includes a "designed-to-fit" stainless steel bracket, mounting hardware, and pre-assembled hoses for easy installation—no drilling or special tools needed. Note: This kit has been redesigned to fit directly behind the outlet of the airbox on the firewall, using the factory tab located on the firewall.
Despite skepticism from "forum experts and social hysteria," an Oil Catch Can (OCC) is essential. Many MINI owners suffer from carbon buildup on their intake valve due to oil being recycled through the intake tract. With the M7 Oil Catch Can, your MINI Cooper's engine will be protected from excessive oil and hydrocarbon buildup, preventing performance-hindering oil film and sludge. Direct injection in 2007 & up MINIs exacerbates the issue, leading to oil blow-by burning onto intake valves, resulting in power loss and expensive repairs.
By capturing excess oil vapor and particles, the M7 Oil Catch Can ensures optimal engine performance. Now with our exclusive "Exact-Fit" pre-assembled hose kit and brackets, installation is super easy.
The M7 Oil Catch Can is not only functional but also a work of automotive performance ART! It features a 100% carbon fiber housing with CNC machined billet aluminum top and bottom, adding a sharp look to your engine compartment.
All hoses, brackets, clamps, necessary fittings, and easy-to-follow detailed step-by-step instructions are included, along with an oil drain plug and an easy-to-view sight tube. The sight tube allows you to monitor the oil level in the can. The hoses are high-quality "Made in the USA" automotive grade, designed to withstand the rigors of the under-hood environment without degradation.
Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent. The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories. These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.
Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.
This part fits the following BMW engines:
S54
This part fits the following chassis:
E46, Z3, Z4
Enhance your R60/R61 Countryman and Paceman with the M7 Oil Catch Can Kit, meticulously crafted by M7 Speed. This kit is an ideal bolt-in solution, precisely tailored for the Mini Cooper platform, ensuring a seamless installation process without any modifications required. Featuring pre-assembled hoses and stainless steel mounting hardware, this catch can kit ensures hassle-free setup. It effectively prevents oil contamination in the intake tract, protects against premature sensor failure, and maintains consistent engine performance at its peak. Crafted from bright black anodized billet aluminum and stainless steel bracket, this catch can kit not only ensures functionality but also adds a sophisticated touch to your engine compartment.
M7 Speed proudly presents the Limited Edition Turbo Heat Shield for all Gen 2 Turbocharged 1.6-liter MINI Coopers. This exclusive release features the same top-selling heat shield, now in a custom Hacienda Wrinkle Red powder coat finish. Perfectly complementing the limited edition MAXX Flo intake system also available in this striking red finish.
This new color has gained popularity among young tuner enthusiasts, adding a vibrant touch under the hood and a distinct WOW effect for MINI owners aiming to stand out. Made in the USA from 0.09in [2.2mm] heavy gauge aluminum material, CNC laser cut, and CNC formed, this heat shield ensures consistently high quality. Lined with ceramic thermal insulation on the underside, it minimizes heat transfer to the hood and top side of the engine compartment, proven effective even on professional race cars subjected to extreme heat.
M7 Speed leads the way in MINI adventure motoring, overlanding, and ultimate performance products. Committed to exceptional customer service and product innovation, we engineer and produce high-quality, easy-to-install aftermarket performance products. Located in Mooresville, North Carolina, known as Race City USA, we're at the heart of North American motorsports.
Upgrade your BMW MINI Cooper S with the M7 Oil Catch Can, designed to protect your engine by separating oil vapors from the crankcase air. This efficient system prevents oil contamination in the intake system, ensuring peak performance and preserving critical components.
This catch can is an easy DIY installation project, featuring high-quality "Made in the USA" automotive-grade hoses, ensuring durability and compatibility with oil exposure. Don't settle for silicone hoses that deteriorate over time and create a mess in your engine compartment. Trust in the M7 Oil Catch Can to safeguard your engine.
The newly updated R55 through R59 Oil Catch Can kit for MINIs equipped with the N16 or N18 engine comes with a "designed-to-fit" stainless steel bracket, mounting hardware, and pre-assembled hoses. Installation is super easy... no drilling and no special tools are needed.
Note: This kit has been redesigned to fit on the firewall directly behind the outlet of the airbox. It uses the factory tab located on the firewall.
"Forum experts and social hysteria" may say an OCC is not needed, but we beg to differ. Many MINI owners suffer from carbon buildup on their intake valve due to oil being recycled through the intake tract to be burned.
With the M7 Oil Catch Can, your MINI Cooper's engine will be protected from excessive oil and hydrocarbon buildup, which leads to performance-hindering oil film and sludge along your intake tract, on your engine control sensors, and on your engine's intake valves.
This oil film & sludge can appear in other critical places throughout the engine, such as the intercooler and the MAF sensor (Mass Air Flow), where clean surfaces are critical for maximized heat transfer and engine performance.
With our exclusive "Exact-Fit" pre-assembled hose kit and brackets, installation is super-easy. All hoses, brackets, clamps, necessary fittings, and easy-to-follow detailed step-by-step instructions are included. An oil drain plug and an easy-to-view sight tube are also provided, allowing you to monitor the oil level in the can.
Beware of other "low-cost" catch can systems that use silicone hoses, as oil and silicone are not compatible and silicone hoses will eventually deteriorate, causing a mess in your engine compartment.
BMW Supercharger Kits can be found all over the internet, but who should you choose to go with? If you want to go to with a forced induction system and want reliability and a driving feel that isn't adversely affected, the VF Engineering Supercharger Kit is one of the best options on the market. Included with every supercharger system is their custom proprietary VF.GIAC software that safely realigns all fueling and engine management parameters for optimal performance and long term drivability. Unlike many other options that are available, the VF Supercharger kit is designed to work with BMW's OEM parameters to minimize the likelihood of DTCs (Diagnostic Trouble Codes) and Check Engine Lights.
This 6.0 psi VF Engineering supercharger system is designed for simple bolt-on installation, remains fully OBD2 compliant, and can be installed in a single day, ready to run in approximately 8 hours. This kit is also non-intrusive and is fully reversible.
The 6.0 psi manifold at peak boost was tested to be the optimal induction charge limit without aftercooling and offers max tourqe gains!
Upon ordering, you will be required to send your VIN number, ECU, and transmission type (auto or manual) to VF Engineering within 1 year of purchase for your software flash of the ECU.
This product is supported by a 1 year unlimited mileage warranty on the product only.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
BMW Supercharger Kits can be found all over the internet, but who should you choose to go with? If you want to go to with a forced induction system and want reliability and a driving feel that isn't adversely affected, the VF Engineering Supercharger Kit is one of the best options on the market. Included with every supercharger system is their custom proprietary VF.GIAC software that safely realigns all fueling and engine management parameters for optimal performance and long term drivability. Unlike many other options that are available, the VF Supercharger kit is designed to work with BMW's OEM parameters to minimize the likelihood of DTCs (Diagnostic Trouble Codes) and Check Engine Lights.
This 6.0 psi VF Engineering supercharger system is designed for simple bolt-on installation, remains fully OBD2 compliant, and can be installed in a single day, ready to run in approximately 8 hours. This kit is also non-intrusive and is fully reversible.
The 6.0 psi manifold at peak boost was tested to be the optimal induction charge limit without aftercooling and offers max tourqe gains!
Upon ordering, you will be required to send your VIN number, ECU, and transmission type (auto or manual) to VF Engineering within 1 year of purchase for your software flash of the ECU.
This product is supported by a 1 year unlimited mileage warranty on the product only.
BMW Supercharger Kits can be found all over the internet, but who should you choose to go with? If you want to go to with a forced induction system and want reliability and a driving feel that isn't adversely affected, the VF Engineering Supercharger Kit is one of the best options on the market. Included with every supercharger system is their custom proprietary VF.GIAC software that safely realigns all fueling and engine management parameters for optimal performance and long term drivability. Unlike many other options that are available, the VF Supercharger kit is designed to work with BMW's OEM parameters to minimize the likelihood of DTCs (Diagnostic Trouble Codes) and Check Engine Lights.
This 6.0 psi VF Engineering supercharger system is designed for simple bolt-on installation, remains fully OBD2 compliant, and can be installed in a single day, ready to run in approximately 8 hours. This kit is also non-intrusive and is fully reversible.
The 6.0 psi manifold at peak boost was tested to be the optimal induction charge limit without aftercooling and offers max tourqe gains!
Upon ordering, you will be required to send your VIN number, ECU, and transmission type (auto or manual) to VF Engineering within 1 year of purchase for your software flash of the ECU.
This product is supported by a 1 year unlimited mileage warranty on the product only.
BMW Supercharger Kits can be found all over the internet, but who should you choose to go with? If you want to go to with a forced induction system and want reliability and a driving feel that isn't adversely affected, the VF Engineering Supercharger Kit is one of the best options on the market. Included with every supercharger system is their custom proprietary VF.GIAC software that safely realigns all fueling and engine management parameters for optimal performance and long term drivability. Unlike many other options that are available, the VF Supercharger kit is designed to work with BMW's OEM parameters to minimize the likelihood of DTCs (Diagnostic Trouble Codes) and Check Engine Lights.
This 6.0 psi VF Engineering supercharger system is designed for simple bolt-on installation, remains fully OBD2 compliant, and can be installed in a single day, ready to run in approximately 8 hours. This kit is also non-intrusive and is fully reversible.
The 6.0 psi manifold at peak boost was tested to be the optimal induction charge limit without aftercooling and offers max tourqe gains!
Upon ordering, you will be required to send your VIN number, ECU, and transmission type (auto or manual) to VF Engineering within 1 year of purchase for your software flash of the ECU.
This product is supported by a 1 year unlimited mileage warranty on the product only.
BMW offers their M Performance retrofit kit for your 340i/i xDrive & 440i/i xDrive for increased power and a more aggressive sounding and free flowing exhaust! This system directly from BMW is perfect for those looking for more power and an aggressive exhaust note without voiding the warranty! Upon installation, an immediate improvement is noticed, especially in the low to mid range powerband. The kit increases your vehicle’s power by 35 hp to 355hp and 39 lb-ft of torque to 369 lb-ft (355 lb-ft for manual transmission vehicles).The BMW M Performance Power kit now comes bundled with a higher flowing, valve controlled exhaust for maximum performance and exhilaration! The BMW M Performance Power Kit features engine tuning software and an electronically controlled valve exhaust system that is actuated in Sport/Sport+ modes via the driving experience control button.
Included with the Power and Sound Kit:
After ordering this kit, simply take this to your dealer to have the ECU re-flashed and all of the components included installed!
The muffler included must also be used with the following BMW exhaust tips:
*Dealer pricing for installation varies from dealer to dealer. Please contact your dealer for installation cost before purchasing.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
BMW offers their M Performance retrofit kit for your 540i/i xDrive for increased power and a more aggressive sounding and free flowing exhaust! This system directly from BMW is perfect for those looking for more power and an aggressive exhaust note without voiding the warranty! Upon installation, an immediate improvement is noticed, especially in the low to mid range powerband.
Included with the Power and Sound Kit:
After ordering this kit, simply take this to your dealer to have the ECU re-flashed and all of the components included installed!
The muffler included must also be used with the following BMW exhaust tips:
*Dealer pricing for installation varies from dealer to dealer. Please contact your dealer for installation cost before purchasing.
**Vehicles without the M Sport Package or Aerodynamics Package will require alterations to the rear bumper and cut out trims (BMW Part # 51122447338 for proper fitment.
Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent. The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories. These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.
Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.
This part fits the following BMW engines:
S54
This part fits the following chassis:
E46, Z3, Z4
The M7 Speed 4% oversize crankshaft pulley is your ticket to unlocking the hidden potential of your MINI Cooper. This performance-enhancing pulley is designed to add power, acceleration, and overall performance to your beloved MINI. Here's how it does the trick:
The M7 Speed 4% Crank Pulley isn't just about performance; it's also a work of art. Crafted with advanced computer modeling and precision CNC machining, it's a blend of form and function:
Use it in conjunction with the M7 Speed 16% Supercharger Technology Pulley for peak performance in MINI tuning.
From the factory, MINI lacks a positive drive key on the crankshaft snout to drive the lower pulley. Most aftermarket pulleys are slip-fit and rely on the bolt to prevent slippage. The M7 Speed crank pulley is engineered differently:
The pulley is interference-fit onto the crankshaft, ensuring zero slippage even at high RPMs.
Proudly made in the USA, the M7 Speed 4% Oversize Crankshaft Pulley is the upgrade your MINI Cooper deserves. Unleash its hidden power and enjoy a new level of performance, reliability, and overall driving pleasure. Get ready to experience the difference.
BMW Supercharger Kits can be found all over the internet, but who should you choose to go with? If you want to go to with a forced induction system and want reliability and a driving feel that isn't adversely affected, the VF Engineering Supercharger Kit is one of the best options on the market. Included with every supercharger system is their custom proprietary VF.GIAC software that safely realigns all fueling and engine management parameters for optimal performance and long term drivability. Unlike many other options that are available, the VF Supercharger kit is designed to work with BMW's OEM parameters to minimize the likelihood of DTCs (Diagnostic Trouble Codes) and Check Engine Lights.
This 6.0 psi VF Engineering supercharger system is designed for simple bolt-on installation, remains fully OBD2 compliant, and can be installed in a single day, ready to run in approximately 8 hours. This kit is also non-intrusive and is fully reversible.
The 6.0 psi manifold at peak boost was tested to be the optimal induction charge limit without aftercooling and offers max tourqe gains!
Upon ordering, you will be required to send your VIN number, ECU, and transmission type (auto or manual) to VF Engineering within 1 year of purchase for your software flash of the ECU.
This product is supported by a 1 year unlimited mileage warranty on the product only.
Introducing the complete and easy bolt-in "Exact-Fit" M7 Oil Catch Can kit for the R60/R61 Countryman and Paceman. Designed by M7 Speed, this kit is a perfect fit onto the R60/R61 Mini Cooper platform with no modifications required. Even the hoses are pre-cut and assembled to exact length! The kit includes a stainless steel bracket, stainless steel mounting hardware, and pre-assembled hoses for hassle-free installation—no drilling or special tools needed.
The "Exact-Fit" pre-assembled hoses eliminate the need to cut the factory breather tube, allowing easy restoration to stock configuration when it's time to sell your car.
The M7 Oil Catch Can is not just functional—it's a work of automotive performance art! CNC machined from billet aluminum, it adds a sharp look to your engine compartment.
Why install an M7 oil catch can? The M7 Oil Catch Can protects your MINI Cooper's engine from excessive oil and hydrocarbon buildup, which can lead to performance-hindering oil film and sludge on your intake tract, engine control sensors, and intake valves. With direct injection in 2007 & up MINIs, the intake valves don't get cleaned, leading to oil residue buildup. By capturing excess oil vapor and particles, the M7 Oil Catch Can ensures optimal engine performance.
The kit includes all necessary hoses, brackets, clamps, fittings, and easy-to-follow step-by-step instructions, as well as an oil drain plug and an easy-to-view sight tube. The sight tube lets you monitor the oil level in the can. The hoses are high-quality "Made in the USA" automotive grade, designed to withstand the under-hood environment without degradation.
Don't settle for less—choose M7 Speed products!
Engineered, tested, and proven to PERFORM!
BMW Supercharger Kits can be found all over the internet, but who should you choose to go with? If you want to go to with a forced induction system and want reliability and a driving feel that isn't adversely affected, the VF Engineering Supercharger Kit is one of the best options on the market. Included with every supercharger system is their custom proprietary VF.GIAC software that safely realigns all fueling and engine management parameters for optimal performance and long term drivability. Unlike many other options that are available, the VF Supercharger kit is designed to work with BMW's OEM parameters to minimize the likelihood of DTCs (Diagnostic Trouble Codes) and Check Engine Lights.
This 6.0 psi VF Engineering supercharger system is designed for simple bolt-on installation, remains fully OBD2 compliant, and can be installed in a single day, ready to run in approximately 8 hours. This kit is also non-intrusive and is fully reversible.
The 6.0 psi manifold at peak boost was tested to be the optimal induction charge limit without aftercooling and offers max tourqe gains!
Upon ordering, you will be required to send your VIN number, ECU, and transmission type (auto or manual) to VF Engineering within 1 year of purchase for your software flash of the ECU.
This product is supported by a 1 year unlimited mileage warranty on the product only.
Looking for an affordable yet high-performance fresh air system for your 2007-2016 R55-R61 Turbocharged MINI Cooper? Look no further than M7 Speed's MAXX-FLO™ low restriction intake system. Engineered for easy installation and unparalleled performance, this system is the ultimate solution for MINI enthusiasts.
Both kits come complete with all necessary installation hardware and easy-to-follow instructions, ensuring a hassle-free upgrade experience.
As the world leader in MINI Cooper adventure motoring, overlanding, and ultimate performance products, M7 Speed is committed to exceptional customer service and product innovation. Based in Mooresville, North Carolina—known as Race City USA—our focus is on engineering and producing high-quality, easy-to-install aftermarket performance products.
Choose between red (56-315102) or black (56-315101) and elevate your MINI driving experience today!
Upgrade your 2007-2016 R55-R61 Turbocharged MINI Cooper with the ultimate in affordability and high performance: the MAXX-FLO (TM) Low Restriction Intake System from M7. Engineered for super easy installation, this C.A.R.B. listed intake system is designed to solve common issues found in aftermarket fresh air systems.
Paired with the redesigned M7 Tuning Turbo Heat Shield, not only does this system protect your Gen 2 MINI from turbocharger heat damage, but it also adds a polished finish to your engine compartment. Available in red (56-315102) or black (56-315101), choose the perfect match for your MINI or gift one to the MINIAC in your life today!
Additionally, the M7 Speed exclusive Vacuum Line Relocator Kit is included, providing parts and instructions to safely remove the unsightly OE line and reroute it out of sight, enhancing the visual appeal of your open-hood setup.
Both kits are equipped with all necessary installation hardware and easy-to-follow instructions for a hassle-free upgrade experience.
M7 Speed leads the world in MINI Cooper adventure motoring, overlanding, and ultimate performance products. Committed to exceptional customer service and product innovation, we engineer and produce high-quality, easy-to-install aftermarket performance products. Located in Mooresville, North Carolina, at the heart of North American motorsports, M7 Speed is situated in Race City USA.
Upgrade your R55-R59 N18 engine's oil catch can hoses with the Replacement M7 Speed Oil Catch Can Hose Kit. Specifically designed for Generation 2 engines, this kit includes two hoses with the correct adapters for connecting to the engine cam cover PCV hose. Please note that hardware, clamps, and brackets are not included with this kit.
