Ensure proper sealing when installing the turbos on your N54.

Kit includes:

• 16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

Elevate your BMW's performance with the JMTC Dual Scroll JM40 K03 turbocharger, meticulously engineered as a reliable and high-performance upgrade compatible with all OEM components. Featuring a high-flow twin-scroll design with an extended tip compressor, this turbocharger ensures early boost delivery and sustained performance throughout the RPM range. Experience exceptional torque, rapid spooling, and sustained power gains across the power-band, offering superior response and increased performance for your BMW.

Benefits:

• High-flow twin-scroll JM40 turbocharger for BMW upgrades
• Extended tip compressor for early and sustained boost
• Outstanding torque and power gains across the entire RPM range
• Compatible with Mini Cooper N14, N18, and Peugeot RCZ 200 (THP engine)
• Fits OEM intake boot and various aftermarket intake systems

JMTC Super S F56 Turbocharger for MINI

For MINI enthusiasts seeking a powerful upgrade, the JMTC Super S F56 turbocharger is engineered for both street and track performance. Designed with a 50mm compressor and a 9-blade high-flow turbine, this turbocharger offers rapid boost and significant power gains at higher RPMs. It maintains the quick response of the original turbo while delivering increased torque and horsepower.

Key Benefits:

• Billet Compressor: Ensures high durability and performance.
• High Flow 9-Blade Lightened Turbine: Provides quick spooling and efficient power delivery.
• High Strength Internals: Designed to withstand higher pressures.
• Upgraded 360-Degree Bearing: Enhances reliability and performance.
• High-Temperature Alloy Turbine Housing: Resists heat for consistent performance.
• Water-Cooled Bearing Housing: Improves cooling and longevity.
• Quick Spooling Dual Scrolling Housing: Reduces lag and enhances responsiveness.
• Power Increase: Up to 300 BHP for Cooper S and 320 BHP for JCW with supporting mods and ECU tuning.

Important Notes:

• The turbocharger does not include an electric actuator; use the one from your old turbo.
• For optimal results, consider refurbishing your OEM catalytic converter or using a high-flow downpipe. Installing a new oil line is also recommended to prevent future issues.
• Turbocharger rebuilds include a complete overhaul and replacement of any worn or damaged components, with a full warranty on rebuilt parts.

Turbo maintenance has become part of our daily lives here. Our Service department does several turbo overhauls, wastegate adjustments, carbon cleaning, and upgrades every week. For the DIY owner, however, having a complete overhaul kit takes some of the stress out of 335 turbo replacement and this kit includes all of the basic items. It's highly likely N54 turbos will have to be replaced before 100,000 miles. Signs of a failing turbo are high oil consumption and blue smoke from exhaust (not from a leak or failing CCV system) because the internal oil seals are no longer retaining oil. Without critical lubrication and cooling effects from oil, the turbo shafts and bearings are usually the first to wear and that requires a complete rebuild. You might also see increased turbo lag or failure to hold boost, which is usually a sign of a failing wastegate or some other internal issue. With any internal problems the turbos need to be replaced. 

This package uses new (not rebuilt) Mitsubishi turbochargers (the original supplier to BMW). These are essentially direct replacement turbos but we went straight to the manufacturer instead of going through BMW. They are the same as the factory turbos but without a BMW logo so you save yourself a few hundred dollars. It includes everything that needs replacement during a 335 N54 twin turbo overhaul -

• Front and rear new OEM Mitsubishi turbos (the original supplier of BMW turbos)
• 1 gallon of Genuine BMW coolant
• ​16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

These are brand-new turbos so a core charge does not apply.

Turbo maintenance has become part of our daily lives here. Our Service department does several turbo overhauls, wastegate adjustments, carbon cleaning, and upgrades every week. For the DIY owner, however, having a complete overhaul kit takes some of the stress out of 135/535 turbo replacement and this kit includes all of the basic items. It's highly likely N54 turbos will have to be replaced before 100,000 miles. Signs of a failing turbo are high oil consumption and blue smoke from exhaust (not from a leak or failing CCV system) because the internal oil seals are no longer retaining oil. Without critical lubrication and cooling effects from oil, the turbo shafts and bearings are usually the first to wear and that requires a complete rebuild. You might also see increased turbo lag or failure to hold boost, which is usually a sign of a failing wastegate or some other internal issue. With any internal problems the turbos need to be replaced. 

This package uses new (not rebuilt) Mitsubishi turbochargers (the original supplier to BMW). These are essentially direct replacement turbos but we went straight to the manufacturer instead of going through BMW. They are the same as the factory turbos but without a BMW logo so you save yourself a few hundred dollars. It includes everything that needs replacement during a 135 or 535 N54 twin turbo overhaul -

• Front and rear new OEM Mitsubishi turbos (the original supplier of BMW turbos)
• 1 gallon of Genuine BMW coolant
• ​16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

These are brand-new turbos so a core charge does not apply.