BMW Fuel System Parts

ARC Upgraded Fuel Pump Control Module - Dual Ball Bearing Fan - EKPM3...

T#:28304525

Part#: EKP-HW05-E-SF

In Stock

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

Arc Terminator now offers upgraded EKMP3 Fuel Pump Control Modules featuring a 22 Amp INCREASE in maximum current capacity over an OEM EKPM3. This allows for more current to be supplied to your low-pressure fuel pump (LPFP) without risking thermal overload, which often leads to your car shutting down. This means that you won't have to worry about being stranded on the side of the road while waiting for your EKP module to cool down, especially when you've installed a large low-pressure fuel pump such as a Walbro 525lph. How does the integrated automatic cooling work? The integrated automatic cooling works by us installing a thermal activation switch directly onto the new half bridge IC. When the half bridge IC reaches 50°C, the 40mm fan will turn on and keep running until the IC is below 50°C or until the EKMP3 stops receiving power. I have an EKPM2, can I upgrade to this? Yes. You can upgrade to this. We recommend using the HW05 and below module. You will need to code it in order for it to function properly. Can I run more than 1 low-pressure fuel pump off of this module? No. We do not recommend that you use more than one low-pressure fuel pump with any EKP module due to the factory wiring supplying power to the EKP Module is only 12 gauge, which is not rated for the type of power demands that two low-pressure fuel pumps would require.

Show More Show Less

Upgraded Fuel Pump Control Module - Dual Ball Bearing Fan - EKPM3 ...

T#:28304531

Part#: EKP-HW06-F-SF

In Stock

$ 209.99 USD

Add to Wish List

Qty

$ 209.99 USD

Add to Wish List

Arc Terminator now offers upgraded EKMP3 Fuel Pump Control Modules featuring a 22 Amp INCREASE in maximum current capacity over an OEM EKPM3. This allows for more current to be supplied to your low-pressure fuel pump (LPFP) without risking thermal overload, which often leads to your car shutting down. This means that you won't have to worry about being stranded on the side of the road while waiting for your EKP module to cool down, especially when you've installed a large low-pressure fuel pump such as a Walbro 525lph. How does the integrated automatic cooling work? The integrated automatic cooling works by us installing a thermal activation switch directly onto the new half-bridge IC. When the half-bridge IC reaches 50°C, the 40mm fan will turn on and keep running until the IC is below 50°C or until the EKMP3 stops receiving power. Can I run more than 1 low-pressure fuel pump off of this module? No. We do not recommend that you use more than one low-pressure fuel pump with any EKP module due to the factory wiring supplying power to the EKP Module is only 12 gauge, which is not rated for the type of power demands that two low-pressure fuel pumps would require.

Show More Show Less

BMW F Chassis Upgraded Fuel Pump Control Module - Noctua Fan - EKPM3 ...

This service will not work for M-Cars or any B-Series motors

T#:28304534

Part#: EKP-HW06-F-NF

In Stock

$ 239.99 USD

Add to Wish List

Qty

$ 239.99 USD

Add to Wish List

Arc Terminator now offers upgraded EKMP3 Fuel Pump Control Modules featuring a 22 Amp INCREASE in maximum current capacity over an OEM EKPM3. This allows for more current to be supplied to your low-pressure fuel pump (LPFP) without risking thermal overload, which often leads to your car shutting down. This means that you won't have to worry about being stranded on the side of the road while waiting for your EKP module to cool down, especially when you've installed a large low-pressure fuel pump such as a Walbro 525lph. Includes 40mm Noctua Silent Fan! How does the integrated automatic cooling work? The integrated automatic cooling works by us installing a thermal activation switch directly onto the new half-bridge IC. When the half-bridge IC reaches 50°C, the 40mm fan will turn on and keep running until the IC is below 50°C or until the EKMP3 stops receiving power. Can I run more than 1 low-pressure fuel pump off of this module? No. We do not recommend that you use more than one low-pressure fuel pump with any EKP module due to the factory wiring supplying power to the EKP Module is only 12 gauge, which is not rated for the type of power demands that two low-pressure fuel pumps would require.

Show More Show Less

Port Injector Plugs

T#:27171925

Part#: UNI-BMS-PIPLUGS

In Stock

$ 60.00 USD

Add to Wish List

Qty

$ 60.00 USD

Add to Wish List

These dummy injectors fit in place of port injection fuel injectors to block the holes. Allows use to aluminum manifolds with port injection bungs without having to purchase fuel injectors. Plugs are EV14 injectors and measure 38mm or 1.5" from o-ring to o-ring.

Show More Show Less

Fuel Pump Cam Follower - BMW/MINI B46 B48 B58

We Price Match - Give Us A Call or Chat!

T#:39768327

Part#: 06H109311B

In Stock

$ 29.99

This product was last offered at the strikethrough price on
06-25-2026

$ 28.95 USD

Add to Wish List

Qty

$ 28.95 USD

Add to Wish List

BMW N54 Port Injection Intake Manifold With 750cc Injectors And Fuel ...

T#:21933055

Part#: N54PIIMINJECT

In Stock

$ 988.00 USD

Add to Wish List

Qty

$ 988.00 USD

Add to Wish List

BMW N54 Port Injection Intake Manifold With 750cc Injectors And Fuel Line Kit - Phoenix Racing is a high-performance upgrade engineered to replace the stock plastic intake manifold on BMW N54 engines. Constructed from durable, lightweight aluminum, this manifold increases airflow and strength, delivering reliable performance for both street and track applications. Integrated with top-mount port injection bungs, this manifold ensures optimal fuel delivery and spray patterns for maximum efficiency. The Phoenix Racing kit includes calibrated 750cc injectors and a plug-and-play fuel line, making it ideal for drivers aiming for high horsepower and seamless installation. Available through Turner Motorsport.

Replaces the factory plastic manifold with high-strength aluminum for increased durability and performance
Supports increased airflow to enhance engine power and efficiency
Integrated top-mount port injection bungs optimize fuel injector spray and delivery
Includes calibrated 750cc injectors and plug-and-play fuel line for a complete port injection solution
Multiple expansion vacuum ports support blow-off valves, boost gauges, Hobb’s switches, and more
High-quality, high-temperature o-rings provide lasting durability and reliability
Exclusively available through Turner Motorsport, ensuring trusted quality and service

Show More Show Less

F3X/F2X - N55 EKP PNP Cooler Kit

A Must For Cars With Upgraded LPFPs

T#:26471608

Part#: AT223F22BLA501N5

Ships in 1 Business Day

$ 44.99 USD

Add to Wish List

Qty

$ 44.99 USD

Add to Wish List

A Must For Cars With Upgraded LPFPs The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With 5015 Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

E90 / E92 / E93 Silent Fan EKP PNP Cooler Kit - 40mm Noctua Fan ...

A Must For Cars With Upgraded LPFPs

T#:26404814

Part#: SILENT-E90-EKP

Ships in 1 Business Day

Starting at $ 59.99 USD

Add to Wish List

Starting at $ 59.99 USD

Add to Wish List

The full plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E9X BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. Please note that if you have an HW06 + (Slim EKPM3), you must choose the HW06 option, as the pre-HW06 housings will not fit. Installation Tips: https://arcterminator.com/pages/e90-e92-e93-ekp-cooler-install-instructions We recommend using Fuse #8 (2007+ E9X), which is the cigarette lighter fuse to power this. It is a 20 amp fuse, which you will just need to pull out and put it into the empty slot of the fuse holder that comes with the kit. Then you'll need to put that fuse holder into the now empty #8 fuse slot. This ensures that the fan will only turn on when the ignition in the car is turned on. You'll also need trim removal tools, as well as a 10mm socket to remove and re-install the EKP module. We recommend using the stock grounding point that's above the EKP module or the EKP module's mounting points as the ground. The ring terminal with the kit will fit either location. The whole installation should take you between 30 - 45 minutes. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable ASA, ABS, or PETG. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With a Genuine Noctua 60mm or 40mm Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 8x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a silent Noctua fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

F3X/F2X - N20 EKP PNP Cooler Kit

A Must For Cars With Upgraded LPFPs

T#:26471604

Part#: AT226F22BLA501N2

Ships in 1 Business Day

$ 44.99 USD

Add to Wish List

Qty

$ 44.99 USD

Add to Wish List

The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With 5015 Fan or 60mm Noctua Fan (depending on choice) 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

Upgraded EKPM3 Fuel Pump Control Module - Noctua Fan

T#:28304530

Part#: EKP-HW05-E-NF

Back Ordered

$ 229.99 USD

Add to Wish List

Qty

$ 229.99 USD

Add to Wish List

Arc Terminator now offers upgraded EKMP3 Fuel Pump Control Modules featuring a 22 Amp INCREASE in maximum current capacity over an OEM EKPM3. This allows for more current to be supplied to your low-pressure fuel pump (LPFP) without risking thermal overload, which often leads to your car shutting down. This means that you won't have to worry about being stranded on the side of the road while waiting for your EKP module to cool down, especially when you've installed a large low-pressure fuel pump such as a Walbro 525lph. Includes 40mm Noctua Silent Fan! How does the integrated automatic cooling work? The integrated automatic cooling works by us installing a thermal activation switch directly onto the new half bridge IC. When the half bridge IC reaches 50°C, the 40mm fan will turn on and keep running until the IC is below 50°C or until the EKMP3 stops receiving power. I have an EKPM2, can I upgrade to this? Yes. You can upgrade to this. We recommend using the HW05 and below module. You will need to code it in order for it to function properly. Can I run more than 1 low-pressure fuel pump off of this module? No. We do not recommend that you use more than one low-pressure fuel pump with any EKP module due to the factory wiring supplying power to the EKP Module is only 12 gauge, which is not rated for the type of power demands that two low-pressure fuel pumps would require.

Show More Show Less

F8X - S55 EKP PNP Cooler Kit

A Must For Cars With Upgraded LPFPs

T#:26471618

Part#: AT225F22BLA501S5

Ships in 1 Business Day

$ 44.99 USD

Add to Wish List

Qty

$ 44.99 USD

Add to Wish List

A Must For Cars With Upgraded LPFPs The full plug-and-play EKPM3 cooler kit is designed specifically for F80, F82, F83, and F87 (Comp) BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With 5015 Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

E90 / E92 / E93 EKP PNP Cooler Kit - (3 Series)

A Must For Cars With Upgraded LPFPs

T#:26271821

Part#: E9X-EKP-PNP

Ships in 1 Business Day

Starting at $ 44.99 USD

Add to Wish List

Starting at $ 44.99 USD

Add to Wish List

This fully plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E9X BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. Please note that if you have an HW06 + (Slim EKPM3), you must choose the HW06 option, as the pre-HW06 housings will not fit. If you have an M3, you must choose an EKPM2 style cooler since the EKP Module has the same physical dimensions as an EKPM2. Installation Tips: https://arcterminator.com/pages/e90-e92-e93-ekp-cooler-install-instructions We recommend using Fuse #8 (2007+ E9X), which is the cigarette lighter fuse to power this. It is a 20 amp fuse, which you will just need to pull out and put into the empty slot of the fuse holder that comes with the kit. Then you'll need to put that fuse holder into the now empty #8 fuse slot. This ensures that the fan will only turn on when the ignition in the car is turned on. You'll also need trim removal tools, as well as a 10mm socket to remove and re-install the EKP module. We recommend using the stock grounding point that's above the EKP module or the EKP module's mounting points as the ground. The ring terminal with the kit will fit either location. The whole installation should take you between 30 - 45 minutes. The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature. Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With 5015 Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 8x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse

Show More Show Less

High-Pressure Fuel Pump Replacement Kit - N55

First time replacement will require T#199513 Adapter for vehicles with production date up to 12/2013

T#:3165724

Part#: 13518604231KT2

In Stock

$ 387.99 USD

Add to Wish List

Qty

$ 387.99 USD

Add to Wish List

This kit includes new HPFP gaskets needed for a complete and easy install. The fuel pump is the heart of your car, pumping fuel to the engine and making your car run. If your fuel pump is broken, replace it with this original BMW part. If your fuel filter is clogged, you must replace the entire fuel pump assembly.

Show More Show Less

Fuel Pump High Pressure Kit

T#:41391177

Part#: 13517588879TKT

In Stock

$ 908.60

This product was last offered at the strikethrough price on
06-03-2026

$ 808.60 USD

Add to Wish List

Qty

$ 808.60 USD

Add to Wish List

Designed for MINI Cooper Turbo N14 engines, this HPFP integrates into the engine bay’s fuel system to efficiently pressurize and supply fuel where it’s needed.

F3X/F2X - N55 Silent EKP PNP Cooler Kit - 40mm Noctua Fan

A Must For Cars With Upgraded LPFPs

T#:26471609

Part#: AT231F22BLA40MN5

Ships in 1 Business Day

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

A Must For Cars With Upgraded LPFPs The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With a single 40mm Noctua Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

E60 / E61 EKPM2 EKPM3 PNP Cooler Kit - (5 Series)

A Must For Cars With Upgraded LPFPs

T#:26305056

Part#: E60-EKP-PNPC

Ships in 1 Business Day

Starting at $ 59.99 USD

Add to Wish List

Starting at $ 59.99 USD

Add to Wish List

The full plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E60 BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. There are two versions of the kit, one with a relay and one without a relay. The relay kit is for those who would prefer to not put an additional load on their 12v outlet circuit due to using that circuit for something with a high load already. The non-relay kit will work perfectly for any normal use of the 12v outlet circuit and only adds up to 0.30 amps onto that circuit, which is very minimal. For all M5s, you will need to use an EKPM2 kit as the EKP module is physically the same size as an EKPM2. Full Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With 5015 Fan and Fused Relay 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 2x 2 Amp Standard Blade Fuses Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

F3X/F2X - B58 Silent EKP PNP Cooler Kit - 40mm Noctua Fan

A Must For Cars With Upgraded LPFPs

T#:26471614

Part#: AT232F22BLA40MB5

Ships in 1 Business Day

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

A Must For Cars With Upgraded LPFPs The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With a single 40mm Noctua Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

E82 Silent Fan EKP PNP Cooler Kit - 40mm Noctua Fan

A Must For Cars With Upgraded LPFPs

T#:26471523

Part#: SILENT-E82-EKP

Ships in 1 Business Day

Starting at $ 59.99 USD

Add to Wish List

Starting at $ 59.99 USD

Add to Wish List

The full plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E82 BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. Please note that if you have an HW06 + (Slim EKPM3), you must choose the HW06 option, as the pre-HW06 housings will not fit. Installation Tips: https://arcterminator.com/pages/e90-e92-e93-ekp-cooler-install-instructions We recommend using Fuse #8 (2007+ E82), which is the cigarette lighter fuse to power this. It is a 20 amp fuse, which you will just need to pull out and put into the empty slot of the fuse holder that comes with the kit. Then you'll need to put that fuse holder into the now empty #8 fuse slot. This ensures that the fan will only turn on when the ignition in the car is turned on. You'll also need trim removal tools, as well as a 10mm socket to remove and re-install the EKP module. We recommend using the stock grounding point that's above the EKP module or the EKP module's mounting points as the ground. The ring terminal with the kit will fit either location. The whole installation should take you between 30 - 45 minutes. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With a Genuine 60mm Noctua Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 8x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a silent Noctua fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

E82 / E88 EKPM2 EKPM3 PNP Cooler Kit - (1 Series)

A Must For Cars With Upgraded LPFPs

T#:26404802

Part#: E82-EKP-PNPC

Ships in 1 Business Day

Starting at $ 44.99 USD

Add to Wish List

Starting at $ 44.99 USD

Add to Wish List

The full plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E82 BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. Please note that if you have an HW06 + (Slim EKPM3), you must choose the HW06 option, as the pre-HW06 housings will not fit. 10% of all proceeds from pink housings sold will be donated towards Breast Cancer research. Installation Tips: https://arcterminator.com/pages/e90-e92-e93-ekp-cooler-install-instructions We recommend using Fuse #8 (2007+ E82), which is the cigarette lighter fuse to power this. It is a 20 amp fuse, which you will just need to pull out and put into the empty slot of the fuse holder that comes with the kit. Then you'll need to put that fuse holder into the now empty #8 fuse slot. This ensures that the fan will only turn on when the ignition in the car is turned on. You'll also need trim removal tools, as well as a 10mm socket to remove and re-install the EKP module. We recommend using the stock grounding point that's above the EKP module or the EKP module's mounting points as the ground. The ring terminal with the kit will fit either location. The whole installation should take you between 30 - 45 minutes. We also offer a DIY kit that includes everything you'll need to create your own active cooling solution here: https://arcterminator.com/products/ekp-active-cooling-diy-kit The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable ASA, ABS or PETG, depending on the color choice. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With 5015 Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 8x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

Turner Motorsport M50 Manifold Fuel Rail Cover

T#:303995

Part#: TEN3680FRC

Ships in 6 Business Days

$ 151.99 USD

Add to Wish List

Qty

$ 151.99 USD

Add to Wish List

Turner Motorsport has spent the last two decades striving for ultimate performance on the racetrack, and transferring the knowledge gained from winning races onto the street. Their line of BMW performance parts combines, high quality, great value, and most importantly, superior performance that will allow you to dial in your ride to suit your driving style and allow your BMW to live up to its full potential. This modified fuel rail cover will fit the M50 manifold, providing a completed look to your engine bay.

Show More Show Less

Complete Fuel Injector Replacement Kit - B58

T#:27171936

Part#: 13538625396KT3

Ships in 5 Business Days

$ 647.99

This product was last offered at the strikethrough price on
08-07-2026

$ 637.99 USD

Add to Wish List

Qty

$ 637.99 USD

Add to Wish List

Basic High Pressure Fuel Pump Replacement Kit

T#:15644266

Part#: 13517616170-KT

In Stock

$ 1,678.35

This product was last offered at the strikethrough price on
06-19-2026

$ 1,677.85 USD

Add to Wish List

Qty

$ 1,677.85 USD

Add to Wish List

HPFP woes? Replacement high pressure exchange pump for the N54 engine. Kit includes: Remanufactured High-pressure fuel pump Intake manifold gasket sets Throttle body gasket

Fuel Injector Replacement Kit

T#:15744008

Part#: 13538627842-KT

In Stock

Sale - Save 26% $ 1,250.99

This product was last offered at the strikethrough price on
06-15-2026

$ 929.26 USD

Add to Wish List

Qty

Sale - Save 26%

$ 1,250.99

This product was last offered at the strikethrough price on
06-15-2026

$ 929.26 USD

Add to Wish List

Replace your old injectors! Includes a full set of Bosch injectors, and decoupling elements.

High Pressure Fuel Pump Replacement Kit - N55 E Chassis

T#:15644274

Part#: 13517616170KT

In Stock

$ 1,783.31

This product was last offered at the strikethrough price on
07-06-2026

$ 1,743.13 USD

Add to Wish List

Qty

$ 1,743.13 USD

Add to Wish List

This extensive kit includes a HPFP and associated gaskets to get the job done right!

F3X/F2X - N20 Silent EKP PNP Cooler Kit - 40mm Noctua Fan

A Must For Cars With Upgraded LPFPs

T#:26471605

Part#: AT234F22BLA40MN2

Ships in 1 Business Day

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With a single 40mm Noctua Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

F8X - S55 Silent EKP PNP Cooler Kit - 40mm Noctua Fan

A Must For Cars With Upgraded LPFPs

T#:26471619

Part#: AT233F22BLA40MS5

Ships in 1 Business Day

$ 59.99 USD

Add to Wish List

Qty

$ 59.99 USD

Add to Wish List

A Must For Cars With Upgraded LPFPs The full plug-and-play EKPM3 cooler kit is designed specifically for F80, F82, F83, and F87 (Comp) BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With a Single Noctua 40mm Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

F3X/F2X - B58 EKP PNP Cooler Kit

A Must For Cars With Upgraded LPFPs

T#:26471615

Part#: AT224F22BLA501B5

Ships in 1 Business Day

$ 44.99 USD

Add to Wish List

Qty

$ 44.99 USD

Add to Wish List

A Must For Cars With Upgraded LPFPs The full plug-and-play EKPM3 cooler kit is designed specifically for F22/F30/F31/F34 BMWs using an EKPM3 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. We designed this kit with the help of Island Racewerks. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x EKPM3 Cooler Housing With 5015 Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

High Pressure Fuel Pump Replacement Kit

T#:5389771

Part#: N55HPFKKT

In Stock

$ 1,783.99

This product was last offered at the strikethrough price on
07-06-2026

$ 1,743.99 USD

Add to Wish List

Qty

$ 1,743.99 USD

Add to Wish List

HPFP woes? Replacement high pressure exchange pump for the N55 engine. Kit includes: Remanufactured High-pressure fuel pump Intake manifold gasket sets Throttle body gasket High pressure fuel sensor No core charge required!

Show More Show Less

B58 Supra Fuel Pump Retrofit - F3X B58

T#:2810083

Part#: 3671725KT

Ships in 2 Business Days

Sale - Save 1% $ 1,308.99

This product was last offered at the strikethrough price on
05-03-2026

$ 1,300.85 USD

Add to Wish List

Qty

Sale - Save 1%

$ 1,308.99

This product was last offered at the strikethrough price on
05-03-2026

$ 1,300.85 USD

Add to Wish List

Includes Required Retrofit Harness - This is a retrofit kit that allows you to run the stock fuel pump found on the B58TU Supra engine on your F chassis B58 car. It has increased flow that will support higher horsepower levels without the need for complex fuel system upgrades. Has been tested to support 600+WHP.

Show More Show Less

Fuel Injector Replacement Kit - N52

T#:53044116

Part#: 13537531634RKT2

In Stock

Sale - Save 22% $ 318.99

This product was last offered at the strikethrough price on
05-03-2026

$ 247.50 USD

Add to Wish List

Qty

Sale - Save 22%

$ 318.99

This product was last offered at the strikethrough price on
05-03-2026

$ 247.50 USD

Add to Wish List

Restore engine performance and drivability by replacing those old, high mileage fuel injectors. Includes injector clips.

N54 High Pressure Fuel Pump Replacement Kit

T#:401622

Part#: 13517616446RKT1

In Stock

$ 1,808.99

This product was last offered at the strikethrough price on
06-19-2026

$ 1,807.99 USD

Add to Wish List

Qty

$ 1,807.99 USD

Add to Wish List

N54 HPFP failure is common with BMWs that use this powerplant. Our Packaged by Turner N54 High Pressure Fuel Pump Replacement Kit includes everything you need to replace your N54 HPFP.

Kit includes:

Genuine BMW Re-manufactured High pressure fuel pump
Intake manifold gasket sets
Throttle body gasket
Low pressure fuel sensor
High pressure fuel sensor

Show More Show Less

High Pressure Fuel Pump Kit

T#:5416773

Part#: N63S63HPFPKT

Ships in 3 Business Days

Sale - Save 7% $ 697.99

This product was last offered at the strikethrough price on
05-03-2026

$ 648.78 USD

Add to Wish List

Qty

Sale - Save 7%

$ 697.99

This product was last offered at the strikethrough price on
05-03-2026

$ 648.78 USD

Add to Wish List

Includes both fuel pumps and a new fuel pressure sensor. Solve your fuel delivery issues kit includes both fuel pumps and a new fuel pressure sensor and hardware.

M54 Complete Fuel Injector Set

T#:5416770

Part#: 13537546245TMSKT

Back Ordered

Sale - Save 9% $ 876.99

This product was last offered at the strikethrough price on
05-03-2026

$ 802.00 USD

Add to Wish List

Qty

Sale - Save 9%

$ 876.99

This product was last offered at the strikethrough price on
05-03-2026

$ 802.00 USD

Add to Wish List

Includes new injector, fuel rail o-ring and injector holder. A vehicle with dirty injectors may host a wide variety of symptoms. From stalling, hesitation, misfiring, and a rough idle, to the wide open throttle woes. If your vehicle is suffering from these symptoms, the fuel injectors may be the cause.

Show More Show Less

High Pressure Fuel Pump Kit

T#:15677496

Part#: 13537622231-KT

Ships in 3 Business Days

Sale - Save 7% $ 697.06

This product was last offered at the strikethrough price on
05-03-2026

$ 648.78 USD

Add to Wish List

Qty

Sale - Save 7%

$ 697.06

This product was last offered at the strikethrough price on
05-03-2026

$ 648.78 USD

Add to Wish List

Solve your fuel delivery issues kit includes both fuel pumps and a new fuel pressure sensor and hardware.

Fuel Filter Kit - M57

T#:56291065

Part#: 13327811227KT2

In Stock

$ 55.42 USD

Add to Wish List

Qty

$ 55.42 USD

Add to Wish List

This fuel service kit pairs a high flow OEM replacement fuel filter with a fresh dampening ring and securing hex bolt. By replacing the filter and hardware together, you ensure fuel pressure stability

JB4PRO Flex Fuel Add On Harness - B58/S58

T#:49822568

Part#: JB4PB58FFAOH

In Stock

$ 49.00 USD

Add to Wish List

Qty

$ 49.00 USD

Add to Wish List

Take your B58 or S58 build further with the JB4PRO Flex Fuel Add-On Harness—a simple, plug-and-play way to add an ethanol sensor and optional fuel pressure sensor to your JB4PRO setup. Keep your install clean, your wiring organized, and your tune dialed to match every fuel blend in the tank. Why it matters: Plug & Play: Connects directly to your JB4PRO—no cutting or splicing required. Sensor Ready: Supports ethanol and fuel pressure sensors for precise, real-time fueling adjustments. Clean, Safe Installation: Includes a 12 V adapter and inline fuse for hassle-free integration. How it works: This harness links your JB4PRO tuner to your flex fuel hardware. It’s not a complete flex fuel kit—you still need a compatible ethanol sensor—but it gives your JB4PRO the accurate readings it needs to adjust timing, boost, and fueling for E30, E50, or E85 blends.

Show More Show Less

Fuel Injector Set

T#:15710786

Part#: 13647597870-KT

In Stock

$ 1,093.99

This product was last offered at the strikethrough price on
05-12-2026

$ 898.99 USD

Add to Wish List

Qty

$ 898.99 USD

Add to Wish List

Refresh your old injectors with these OE fuel injectors! Get your car running its best and prevent any failures or issues prematurely!

x6 injector x6 decoupling element

Fuel pump and level sensor kit

T#:56471664

Part#: 16116768788KT2

Ships in 1 Business Day

$ 664.00 USD

Add to Wish List

Qty

$ 664.00 USD

Add to Wish List

This targeted refresh package to completely restore your E46’s fuel tank module. Built around a high grade Continental fuel pump assembly this kit ensures maximum fuel flow stability, precise fuel gauge readings, and a leak free installation.

Show More Show Less

AUTOTECKNIC Dry Carbon Competition Fuel Cap Cover

T#:21045518

Part#: ATK-BM-0006-BC

Ships in 7 Business Days

$ 65.00 USD

Add to Wish List

Qty

$ 65.00 USD

Add to Wish List

Do you ever go to fill up your car and look at your gas cap and feel like something is missing? Well here you are, the AUTOTACKNIC dry carbon fuel filler cap is here is here to give your old filler cap some high quality personality! Crack a smile every time you open your gas cap!

Show More Show Less

E89 EKP PNP Cooler Kit - (Z4)

A Must For Cars With Upgraded LPFPs

T#:26471566

Part#: E89-EKP-PNP

Ships in 1 Business Day

Starting at $ 44.99 USD

Add to Wish List

Starting at $ 44.99 USD

Add to Wish List

The full plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E89 BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. Please note that if you have an HW06 + (Slim EKPM3), you must choose the HW06 option, as the pre-HW06 housings will not fit. Installation Tips: https://arcterminator.com/pages/e90-e92-e93-ekp-cooler-install-instructions We recommend using Fuse #8, which is the cigarette lighter fuse to power this. It is a 20 amp fuse, which you will just need to pull out and put it into the empty slot of the fuse holder that comes with the kit. Then you'll need to put that fuse holder into the now empty #8 fuse slot. This ensures that the fan will only turn on when the ignition in the car is turned on. You'll also need trim removal tools, as well as a 10mm socket to remove and re-install the EKP module. We recommend using the stock grounding point that's above the EKP module or the EKP module's mounting points as the ground. The ring terminal with the kit will fit either location. The whole installation should take you between 30 - 45 minutes. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable PLA+ or PETG, depending on the color choice. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With 5015 Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 8x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

E-Chassis Stage 3 Bucketless LPFP Upgrade - N54/55

T#:38890918

Part#: BMSS3BLPFPN5455

Ships on Sep 1, 2026

$ 399.99 USD

Add to Wish List

Qty

$ 399.99 USD

Add to Wish List

If you're already using our Stage 2 Bucketless LPFP and want to upgrade to Stage 3, this kit is for you. If you don’t have the Stage 2 kit, you can purchase it here. Note: Stage 3 requires the Stage 2 bucketless kit. The Stage 3 upgrade kit includes: - Complete plug-and-play solution with the addition of the secondary module - Custom billet aluminum fitting to run both pumps in parallel - Wiring harness for the secondary pump - Spare vent tube clip - New Walbro filter - New E85-compatible Walbro 450 pump (F90000274) - Optional upgrade to Walbro 525 pump (F90000285) Recommended accessories: - Lock Ring Removal Tool - Hobb's switch

Show More Show Less

E89 Silent Fan EKP PNP Cooler Kit - 40mm Noctua Fan

A Must For Cars With Upgraded LPFPs

T#:26471534

Part#: SILENT-E89-EKP

Ships in 1 Business Day

Starting at $ 59.99 USD

Add to Wish List

Starting at $ 59.99 USD

Add to Wish List

The full plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E82 BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. Please note that if you have an HW06 + (Slim EKPM3), you must choose the HW06 option, as the pre-HW06 housings will not fit. Installation Tips: https://arcterminator.com/pages/e90-e92-e93-ekp-cooler-install-instructions We recommend using Fuse #8, which is the cigarette lighter fuse to power this. It is a 20 amp fuse, which you will just need to pull out and put it into the empty slot of the fuse holder that comes with the kit. Then you'll need to put that fuse holder into the now empty #8 fuse slot. This ensures that the fan will only turn on when the ignition in the car is turned on. You'll also need trim removal tools, as well as a 10mm socket in order to remove and re-install the EKP module. We recommend using the stock grounding point that's above the EKP module or the EKP module's mounting points as the ground. The ring terminal with the kit will fit either location. The whole installation should take you between 30 - 45 minutes. The cooler housing is designed to fit over the EKP module just like the OEM housing and fits with plenty of room in the stock EKP location. The housing is 3D printed using durable ASA, ABS or PETG, depending on the color choice. The full kit is printed and assembled in the U.S.A. by Arc Terminator LLC. Full Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With a Genuine 60mm or 40mm Noctua Fan 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 8x 4" Zip Ties 1x Alcohol Wipe 1x 2 Amp Mini Blade Fuse Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a silent Noctua fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Show More Show Less

Fuel Pump - High Pressure MINI Cooper

T#:12348304

Part#: 13517588879

Ships in 1 day

$ 899.99 USD

Add to Wish List

Qty

$ 899.99 USD

Add to Wish List

Fuel Pump Kit - E46

T#:56291046

Part#: 16142229684KT2

Ships in 2 Business Days

$ 535.01 USD

Add to Wish List

Qty

$ 535.01 USD

Add to Wish List

A tired fuel pump or a restricted fuel filter can cause dangerous lean spikes under full throttle putting your high strung M engine at risk. The BMW E46 M3 saddle tank relies heavily on both a primary pump and an auxiliary transfer pump to keep fuel moving efficiently across the tank arch during cornering.

Show More Show Less

BMS Gen 1 B58 BMW Aluminum Port Injection Manifold

T#:27171924

Part#: BMSB58G1-PRM

Ships in 8 Business Days

Starting at $ 3,158.00 USD

Add to Wish List

Starting at $ 3,158.00 USD

Add to Wish List

Add more fuel via port Injection while increasing airflow in your Gen 1 B58 Powered BMW When it comes to intake manifolds it doesn't get any better than this. The Burger Motorsports intake manifold replaces your weak factory plastic B58 manifold with a direct fit high flow high strength aluminum manifold. Features port injection bungs located on the top of the manifold for easy access and optimal injector spray pattern, and 1/8" expansion vacuum ports perfect for gauges, BOV references, or Hobbs switches. Includes high-quality o-rings and all required hardware. Your factory high-quality intercooler core slides right in. Available with required port injection hardware (calibrated injectors with plug-and-play fuel line), or ala-cart without the extra fueling hardware. The optional high-quality Bosch EV14 42mm fuel injectors are offered in 550cc, 750cc, and 950cc options. For most 700-800whp applications we suggest the 750cc injectors, while the 550cc injectors are suitable for applications below 700whp. This kit includes a FREE $99.00 Burger Motorsports B58 Phenolic Thermal Intake Manifold Spacer FEATURES AND BENEFITS Increased flow Integrated top mount port injection bungs Much stronger than stock Looks amazing under the hood Lightweight aluminum construction All factory connections Extra ports for a BOV, Hobb's switch, or boost gauge Includes upgraded high-temperature o-rings Optional Motiv Reflex + Injector Controller Optional Injector Block Off Plugs Optional Deasthwerks 1000cc Injectors

Show More Show Less

Radium Fuel Hanger Surge Tank Complete Kit - For Walbro Pumps ...

Upgrade Your Low-Pressure Fueling System With this All-Inclusive Kit!

T#:25606665

Part#: N5XFUEL

Back Ordered

Sale - Save 3% $ 1,254.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 1,213.80 USD

Add to Wish List

Sale - Save 3%

$ 1,254.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 1,213.80 USD

Add to Wish List

Introducing the comprehensive N54/N55 Low-Pressure Fueling Solution! With Radium Engineering's Regulated Fuel Hanger Surge Tank at its core, this kit allows you to tailor your fuel pump setup, select an in-line fuel filter, and opt for a wiring kit for multiple LPFP configurations in your N54 or N55-powered E9X 335i. In this setup, the BMW fuel pump serves as a "lift" pump, maintaining fuel volume in the Fuel Hanger Surge Tank via a dedicated orifice. This guarantees sufficient pressure for the venturi jet pump(s) to operate, ensuring consistent fuel delivery. Excess fuel in the FHST cycles back to the OEM tank through a one-way check valve ensuring a steady fuel supply. Unlike conventional surge tanks, which rely on pump flow matching, this FHST employs additional mechanisms to continuously deliver fuel regardless of fluctuations in other fuel sources. When the main tank nears depletion, the lift pump and Fuel Pressure Regulator step in to supply fuel to the FHST. Furthermore, with a boost reference signal (Hobbs Switch), the Fuel Pressure Regulator operates at a 1:1 ratio, allowing fuel pressure to rise proportionally with boost pressure. The low-pressure fuel returning from the Fuel Pressure Regulator is routed back into the surge tank to maintain its fullness. Inside the canister, a 6-hole diverter ensures even fuel dispersion without air bubbles or foaming. The stainless electrical studs included effectively handle high current demands, surpassing the capabilities of compact bulkhead connectors. These resilient connections are sealed against all standard and exotic fuels, with non-conductive acorn nuts provided to prevent accidental short circuits. The kit also includes the necessary electrical hardware for one Walbro fuel pump and the OEM level sender, while the in-tank wiring is insulated with premium chemically resistant ETFE for enhanced durability. If you are planning on running more than one LPFP, you will need to select the Hobbs Switch option for boost reference (to be installed on the manifold or charge pipe), as well as the fuel pump wiring kit! Features: -Drop-In OEM Replacement -Permits 1 or 2 Surge Pumps -1:1 Fuel Pressure Adjustments -Fuel Starvation Protection -Integrated 1-Way Fill Valve -High Current Electrical Hardware -Compatible with Various Pumps -Anodized Aluminum Construction -Gasoline and Ethanol Compliant -Anodized Aluminum 8AN Male Outlet Fitting -Anodized Aluminum Surge Tank Canister -Fuel Resistant Tubing and Wiring -Stainless Steel Hardware -Relay(s) and Fuse(s)

Show More Show Less

Fuel Pump High Pressure Kit, with Fuel Line Tool - R55 - R59 ...

T#:41661208

Part#: 13517588879T1KT

In Stock

$ 943.59

This product was last offered at the strikethrough price on
06-03-2026

$ 844.59 USD

Add to Wish List

Qty

$ 844.59 USD

Add to Wish List

This complete fuel pump replacement kit is a must-have for any owner or technician looking to maintain peak performance and dependability in their BMW or MINI’s direct injection system.

Fuel Pump High Pressure Full Kit w/ Fuel Line Disconnect Tool R55 - R...

T#:41661220

Part#: 13517592429TKT

In Stock

$ 1,020.99

This product was last offered at the strikethrough price on
06-17-2026

$ 968.99 USD

Add to Wish List

Qty

$ 968.99 USD

Add to Wish List

This high-pressure fuel pump (HPFP) is an essential component of the fuel delivery system, designed specifically for MINI Cooper models equipped with the N18 turbocharged engine. Mounted in the engine bay, it pressurizes and delivers fuel from the low-pressure system to the engine’s direct injection system, ensuring optimal performance, fuel efficiency, and smooth engine operation under all driving conditions.

Show More Show Less

N55 Port Injection Kit With Intake Manifold, 950cc Injectors & Fuel L...

T#:42133542

Part#: BMW-N55-PRM-950

Back Ordered

$ 1,138.00 USD

Add to Wish List

Qty

$ 1,138.00 USD

Add to Wish List

Phoenix Racing N54 Port Injection Intake Manifold With 750cc Injector...

T#:44258354

Part#: BMW-N54PORT-750

Back Ordered

$ 988.00 USD

Add to Wish List

Qty

$ 988.00 USD

Add to Wish List

BMW N54 Port Injection Intake Manifold With 750cc Injectors And Fuel Line Kit - Phoenix Racing is a high-performance upgrade engineered to replace the stock plastic intake manifold on BMW N54 engines. Constructed from durable, lightweight aluminum, this manifold increases airflow and strength, delivering reliable performance for both street and track applications. Integrated with top-mount port injection bungs, this manifold ensures optimal fuel delivery and spray patterns for maximum efficiency. The Phoenix Racing kit includes calibrated 750cc injectors and a plug-and-play fuel line, making it ideal for drivers aiming for high horsepower and seamless installation. Available through Turner Motorsport.

Replaces the factory plastic manifold with high-strength aluminum for increased durability and performance
Supports increased airflow to enhance engine power and efficiency
Integrated top-mount port injection bungs optimize fuel injector spray and delivery
Includes calibrated 750cc injectors and plug-and-play fuel line for a complete port injection solution
Multiple expansion vacuum ports support blow-off valves, boost gauges, Hobb’s switches, and more
High-quality, high-temperature o-rings provide lasting durability and reliability
Exclusively available through Turner Motorsport, ensuring trusted quality and service

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results