Drivetrain Mount Kits

Stock mounts are made from soft rubber and are sometimes filled with fluid to give a car the most comfortable ride possible. The soft rubber and fluid helps to reduce the total amount of vibration, noise, and harshness (NVH) that is transferred into the cabin. The problem with this is driveline slop. The stock mounts allow a lot of excess movement and increases the amount of time it takes to transfer power to the wheels.

In order to address this issue, performance mounts can be substituted to reduce the amount of slop and transfer power to the wheel quicker. Two options for this are polyurethane mounts and solid mounts.

Solid mounts are great for an immediate transfer of power but allow for a ton of noise and vibration to be felt and heard in the cabin of the vehicle. This is great for the track where there aren't any issues with excess harshness, but as a daily driver, this can become an annoying pain in the neck.

The best middle ground is Polyurethane. Polyurethane is much stiffer than rubber and gives you the much stiffer feel you may be looking for. This allows for the increase in responsiveness, but isn't so extreme that it transfers all of the sound and vibrations into the cabin. This makes it much more comfortable for daily use while still reinforcing your driveline.

Features:

• Aluminum and Polyurethane Construction
• 80A Durometer Rating
• New Hardware

Collapsing and worn engine mounts can mean big trouble for N52/N54/N55 cars. The stock mounts are filled with fluid that can leak or evaporate over time. That leaves the mount unstable and too flexible to properly support the engine. The side effects of a worn engine mount are: shaking and vibrating engine, driveline twist from engine torque that can break or snap bushings, and broken motor mount arms and bolts. If you're tired of replacing engine mounts you'll be very pleased wtih these solid rubber versions.

Not only are these more reliable than stock fluid-filled mounts, they are slightly stiffer than new stock mounts thanks to a solid rubber construction (no voids in the rubber) but designed for street use so they remain quiet and comfortable. The solid rubber has less deflection than a stock mount, so no wasted engine and transmission motion. Less wasted motion gives you more torque to the wheels (it's not spent twisting the engine) and better shifts.

Sold as a set of matching engine and transmission mounts.

This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335i 335xi - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi - Coupe
2007-2013 E93 BMW 328i 335i 335is - Convertible
2009-2016 E89 BMW Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

Your rear differential is indirectly connected to your right foot through the engine and driveline, and connected to the seat of your pants through the chassis. Soft factory rubber differential bushings absorb vibrations between chassis and differential, providing comfort and softness in both of these connections.

Enter ECS Tuning's In-House Engineered Performance Polyurethane Differential Bushings. By eliminating the deflection factory rubber bushings permit, the connection between your right foot (and your seat) to the wheels is improved. Removal of this slop allows for crisper power transfer from differential to wheels, which means better throttle control while carving a canyon road, drag racing, sliding the rear end out, or just driving to work. This is achieved without the harshness or vibration associated with delrin or solid differential mounts.

Featuring a tough 88A durometer polyurethane and Black anodized 6061-T6 aluminum Sleeve, our Performance Polyurethane Differential Bushings are more resistant to chemicals, ozone degradation, road salt, and general wear and tear than factory rubber bushings, resulting in a longer service life.

Stock mounts are made from soft rubber and are sometimes filled with fluid to give a car the most comfortable ride possible. The soft rubber and fluid helps to reduce the total amount of vibration, noise, and harshness (NVH) that is transferred into the cabin. The problem with this is driveline slop. The stock mounts allow a lot of excess movement and increases the amount of time it takes to transfer power to the wheels.

In order to address this issue, performance mounts can be substituted to reduce the amount of slop and transfer power to the wheel quicker. Two options for this are polyurethane mounts and solid mounts. 

The middle ground is Polyurethane. Polyurethane is much stiffer than rubber, but these still let a large amount of movement in comparison to solid mounts. These are great for sporty, aggressive street driving, but for the track are not ideal.

For the track, solid mounts are great. Solid mounts give you an immediate transfer of power, at the cost of increase NVH. This is great for the track where comfort is the least of your worries and power is all that is important.

Features:

• Aluminum and Polyurethane Construction
• 80A Durometer Rating
• New Hardware