BMW Ignition Coils

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

This is the current replacement for some BMW 6 and 8-cylinder engines built in the late 2000s and after. BMW has made numerous changes to ignition coil part numbers in recent years but has approved this part number to work in the vehicles listed below. It's listed as a replacement coil for N20, N55, and S55 engines. In March 2015 BMW approved it for N51/N52 engines. This part number replaces the previous BMW part number 12137594937 for the cars listed below.

Sold per coil. Includes boot and connector.

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.
 

This item fits the following BMWs:
2006-2010 E60 BMW M5
2006-2010 E63 BMW M6

MSD Performance Coil Pack for MINI

Before ordering, check whether you need round or flat pin connectors for your MINI's coil pack. The type of pin is determined by the connectors that link the coil to the wiring harness. To check, slide the red locking tab to the right, press down on the tab, and pull the connector off the coil. Examine the pins to see if they are flat or round. Reattach the connector by pushing it back on until it clicks, then slide the red locking tab back to the locked position.

This high-performance coil pack is a popular upgrade among MINI owners looking to enhance their vehicle's performance over the stock coil. The installation requires removing the factory bolts from the old coil and modifying the MSD factory sleeves by drilling out 1/16" to fit the stock bolts.

Kits Include:

• MSD Coil Pack
• MSD Wire Set - Red
• Inductance: 7mH
• Maximum Voltage: 36,000 Volts
• Primary Resistance: 0.51 OHMs
• Secondary Resistance: 12K OHMs
• Turns Ratio: 77:1

Key Benefits:

• Upgraded performance over stock coil pack
• Enhances ignition efficiency and engine performance
• High voltage output of 36,000 volts for stronger sparks
• Low primary resistance of 0.51 OHMs for efficient energy transfer
• High secondary resistance of 12K OHMs for improved performance
• Durable construction for long-lasting use

Revitalize your Mini's performance with these spark plug wires and boots, designed to restore power and ensure smooth engine operation. Replace them at 60,000-mile intervals to maintain optimal performance. If you experience low spark or misfires and it's not due to the coil or spark plugs, faulty wires may be the culprit. Don't let rust buildup hinder performance—replace these wires to ensure happy motoring and reliable spark.

• Restores power and performance to your Mini
• Recommended replacement at 60,000-mile intervals
• Addresses issues such as low spark and misfires
• Prevents rust buildup for consistent spark delivery
• Includes plug wires for cylinder 1