BMW Suspension Bushings & Mounts

Worn rubber differential mounts will lead to the differential twisting and shifting around in the rear subframe. Not only will this be noisy but it's bad for driver confidence and bad for the chassis as well. Even on fresh rubber bushings the differential has deflection and twist, especially if the car has been modified for more torque. Since the differential is centrally mounted in the rear subframe, with all suspension mounts interconnected, a differential with too much deflection will affect handling and could even damage the rear subframe.

These 88A urethane E46 M3 diff mounts are much stiffer than stock but still not as solid as our Turner aluminum/Delrin bushings. This set will resist twisting much better than the stock rubber mounts. Included is the front diff mount and two rear mounts in the cover.

Worn rubber differential mounts will lead to the differential twisting and shifting around in the rear subframe. Not only will this be noisy but it's bad for driver confidence and bad for the chassis as well. Even on fresh rubber bushings the differential has deflection and twist, especially if the car has been modified for more torque. Since the differential is centrally mounted in the rear subframe, with all suspension mounts interconnected, a differential with too much deflection will affect handling and could even damage the rear subframe.

These 88A urethane E46 diff mounts are much stiffer than stock but still not as solid as our Turner aluminum/Delrin bushings. This set will resist twisting much better than the stock rubber mounts. Included are the two front diff mounts and the rear mount in the cover.

Urethane mounts keep the differential from twisting under load. As torque is put through the driveline it causes anything to twist and move. The differential is mounted to the subframe and the twisting and deflection can be transferred to the rest of the chassis. With a stiffer mount the differential will not deflect as much. This improves seat-of-the-pants feeling to the driver, giving more feedback for smoother power delivery. In theory, there's also more torque being sent to the drive wheels since it's not being used up shifting the diff weight around.

These are tough 88A durometer urethane bushings with a anodized almunum center sleeve, engineered by ECS. This is a set of E36 diff bushings - 1 for the front and 2 for the rear cover. New high-grade hardware is included (the front bolt has a tendency to snap from all that torque twisting!).

BMW E46 Z4 Rear Polyurethane Differential Bushing Performance is the ultimate upgrade for enhancing the connection between your BMW's chassis and differential. Designed by Turner Motorsport, this performance bushing replaces the soft factory rubber with durable polyurethane, offering superior control and response. By minimizing vibrations and reducing deflection, this bushing ensures a more direct and responsive driving experience, making it a must-have for any performance-oriented BMW E46 or Z4 owner.

• Enhanced Performance: Replaces the soft factory rubber with durable polyurethane for improved driveline response.
• Reduced Vibrations: Minimizes vibrations between the chassis and differential, providing a more connected driving experience.
• Increased Durability: Made from high-quality polyurethane, offering long-lasting performance under demanding conditions.
• Improved Control: Reduces deflection, ensuring a more precise and responsive handling experience.

Due to their soft rubber construction, OE strut mounts are known to wear at an accelerated rate. Many high-mileage vehicles fall victim to strut mount failure, which is commonly associated with annoying clunks, groans, or rattles from the front suspension.

With this issue in mind, ECS Tuning developed their heavy-duty front strut mount with upgraded, higher durometer rubber to resolve sloppy handling and increase longevity. Manufactured precisely within OEM tolerances, these mounts are a perfect fit for your BMW.

Features:

Reduces deflection: Increases vehicle handling and cornering dynamics by removing deflection within the strut mount. Increases longevity: Upgraded rubber construction makes for a stiffer mount, less prone to cracking and general degradation. Developed in-house: Designed and tested by ECS Tuning engineers, this mount is sure to outlast an OE replacement. Upgrade to a better strut mount without sacrificing ride comfort! Improve longevity and ride control all at once.

Want a race-spec rear shock mount but with the comfort of a factory bushing? This ECS rear shock mount combines the precision and articulation of a spherical bearing with the isolation of urethane bushings. The stainless monoball bearing is lined with PTFE lubricant and suspended in 80A urethane and housed in a hard anodized 6061-T6 aluminum mount. The spherical bearing is a better design than most rear shock mounts because it allows the shock to move and tilt without side-loading the shock shaft (which leads to premature failure of the shock). Most Genuine BMW and aftermarket shock mounts are not designed for shock angles and the stress that track or performance driving will put on the shock shaft. The ECS shock mount is properly designed to handle these loads. The internal bearing is also replaceable - it will be years before you have to replace the entire mount. The ECS mount is fully encapsulated to prevent the common shock mount failure of the stock mount design.

ECS RSM features:

• Maintenance free, PTFE lined, stainless steel monoball spherical bearing for full shaft articulation
• 80A polyurethane isolation bushings for NVH control
• Accommodates 10mm, 12mm, or 14mm damper shafts
• Fully constrained shaft mount makes RSM blow out impossible
• Hard anodized 6061-T6 construction
• Fully rebuildable design

* - the RSM comes with the BMW standard 10mm shock shaft bushings. 12mm is used on some performance shocks and 14mm is used on some true motorsport rear shocks.

The ECS Tuning Billet Front Sway Bar Mounting Kit will provide your vehicle with a more rigid mounting solution from the sway bar to chassis than the OEM steel brackets. With an improved sway bar mounting bracket and the included polyurethane sway bar bushings you can expect to achieve an increase in rear sway bar effectiveness and less body roll as a result.

PART DESIGN

The front sway bar mounting brackets are made from a solid piece of 6061-T6 billet aluminum that are precision CNC-machined to bolt into the OEM mounting location while utilizing greaseable, polyurethane bushings. They are Type II black anodized for corrosion protection and include zinc flake coated Class 12.9 alloy steel bolts for premium performance.

The red polyurethane bushings feature a greaseable channel for extended service life and quieter operation than standard polyurethane bushings.

PERFORMANCE FEATURES

Billet & poly mounts replacing the OEM steel & rubber configuration you can expect faster reaction speed and greater effectiveness from your front sway bar due to less deflection. This translates to better handling with sharper, flatter cornering with reduced body roll.

PRODUCT DEVELOPMENT

ECS Billet Front Sway Bar Mounting Kit was designed, engineered, tested and quality inspected by the Research and Development team in our Wadsworth, Ohio facility to ensure the highest level of precision and quality is delivered throughout rigorous long term product testing and leading edge product development methods.

INSTALLATION AND SUPPORT

Installation is simple. Simply unbolt your front sway bar mounting brackets and slip over our poly bushings and billet mounting brackets with the included hardware. That's it! Enjoy better handling and a crisp front suspension.

SPECIAL NOTE: You can use any conventional automotive bearing grease for service.