BMW Suspension Bushings & Mounts

For all 2001 to 2005 325xi and 330xi. For convenience, we have assembled this bushing carrier bracket kit, to save you time when changing our control arm bushings. It includes two bushing carriers with pre-installed bushings (one left, one right) and mounting bolts.

 These bushing brackets fit all 2001, 2002, 2003, 2004, and 2005 model BMW 325xi and 330xi.

The main mounting bolt for the differential in the E36 is susceptible to shearing off during extreme driving conditions. This can cause internal damage to your diff, leaving you stranded at the track or on the side of the road. Active Autowerke's differential support bracket eliminates this issue forever in under an hour installation.

Previously used Active Autowerke Part Number AA-DSB-E36

This product fits the following BMWs:
1992-1999 E36 323i 325i 328i M3

Replacing your struts and shocks? Don't forget the bushings! The rubber mounts for the shocks will go bad over time, especially if you drive hard or the roads are particularly rough. The shock mounts locate the front struts and rear shocks to the car - providing a quiet and vibration-free buffer between the road and the cabin. Shock mounts and bushings can wear out just like any other rubber part on the car. This leads to more noise and harshness reaching the chassis and may complicate your new suspension install. When installing new shocks, that is the perfect time to also replace the mounts. There is no additional time to install them, no special tools required, and doesn't take any extra time! If you re-use the original mounts you have the risk of them failing before your next shock replacement, doubling your labor costs. 

This item fits the following BMWs: 
2006-2012 E9X BMW All xi models - 325xi 328xi 330xi 335xi

The perfect upgrade for any E46, this finned differential cover increases cooling to the rear differential to prevent over heating and possible damage. This is a complete kit including fluid and drain plugs.

Includes the following

• Aluminum finned differential cover
• Drain & fill plug with sealing o-ring
• 2 Quarts of Redline 75w90

This strut and shock mount package covers the front and rear rubber mounts and bushings commonly replaced during a strut and shock install. While you're installing new front struts and rear shocks these are easily installed - there's no additional labor and special tools are not required. Since these pieces are mostly rubber, they dry up and crack over time. Re-using them lead to problems with fitment or noise, and may have safety issues as well. These mounts and pads are the perfect complement to your new shocks to help restore your car's handling and performance.

We sell the basic strut and shock mount package, which includes:

• Front strut mounts (also known as guide support)
• Front strut reinforcement plates (to prevent cracking and deforming of the front strut towers)
• Front strut tower paper washer gaskets
• Front and rear self-locking mounting nuts
• Rear Lifetime Warranty 'Repair Shop' shock mounts
• Rear shock mount reinforcements (to prevent cracking of shock towers)
• Rear shock mount gaskets

In addition, you can add the front spring pads, front bump stops, front dust boots, rear bump stops, and rear dust boots if needed. But please note that some shocks and coil overs come with all or some of these pieces already. If in doubt, check with your supplier on what is included.

We offer three varieties of the rear shock mounts - OEM, Repair Shop, and HP alum-rubber. We recommend either the Repair Shop or HP mounts because the stock OEM design has a flaw that can lead to premature failure of the mounts. The Repair Shop and HP mounts use a different design that will last longer and the Repair Shop mounts also have a lifetime warranty!

This item fits the following BMWs:
1996-1999 E36 BMW M3
1996-2002 Z3 BMW 2.5 2.5i 2.8 3.0i M Coupe

For someone looking for superior performance and longevity these sealed monoball bushings are the best upper thrust bearing you can buy for an F22 2-series or F3X 3/4-series. The advantage of a monoball bearing is that it will not deflect under load. All of the rubber bushings move in all sorts of directions and that changes your alignment, especially when used with big brake kits or when driven hard. The condition worsens as the bushing wears out. The Dinan monoball sits in a CNC machined aluminum housing which has zero deflection. The monoball allows complete freedom of movement but only at the desired angles. What you get is superior steering precision, better handling from more consistent alignment, and almost infinite bushing life. And thanks to the inner liner and sealed rubber boots there's none of the extra noise or reduced service life of fully solid race bushings. 

We strongly advise using these with new control arms. BMW recommends that the bushings be replaced only once per set of control arms. So if your thrust arm bushings have been replaced already then we do not recommend re-using the arms. The other reason is that the aluminum arms stretch over time which will make the bushings loose inside the arm. Other manufacturers recommend filling the stretched arms with paste but replacing the control arm is the better solution.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere.

This item fits the following BMWs:
2014+ F22 F23 BMW 228i M235i
2012+ F30 BMW 320i 328i 335i - Sedan
2012+ F32 BMW 428i 435i - Coupe
2013+ F33 BMW 428i 435i - Convertible
2012+ F34 BMW 328i 335i - Gran Turismo
2012+ F36 BMW 428i 435i - GranCoupe

This kit includes Turner Motorsport solid aluminum differential race mounts pre installed in the differential cover for a quick install. These mounts where developed by Turner Motorsport for their Grand-Am Cup E46 M3 race cars, the advantages of solid aluminum mounts is increased suspension & drivetrain response, less drivetrain loss resulting in more wheel horsepower, and longevity - they effectively last forever. These CNC-machined mounts are a direct replacement for the stock rubber pieces, and have been lightened to remove excess weight. 

Installing a new set of shocks and struts in your BMW? Turner has your back with this complete "cup kit", which contains all the necessary components for ensuring a lasting installation.

See "kit contents" for a detailed list of all components included with this purchase.