BMW Engine Parts for BMW 4 Series G22 (2021+)

The GENIUS2X2 represents a leap forward in power, performance, energy efficiency, and compactness. This advanced charger is a dual-bank system designed for both 6-volt and 12-volt batteries, serving as a charger, maintainer, trickle charger, and battery desulfator all in one. With a rating of 4 amps (2 amps per bank), it caters to all types of lead-acid and lithium-ion batteries, including flooded, gel, AGM, marine, and deep-cycle variants.

Features:

• A two-bank battery charger maintainer rated a 4-amps - 2-amps per bank with a 40Ah capacity range - designed to charge and maintain multiple vehicles like cars, motorcycles, boats, ATVs, RVs, lawnmowers, lawn tractors, trucks, and more.
• Designed for 6-volt and 12-volt lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion batteries.
• An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates.
• Charges batteries as low as 1-volt. Or use the all-new force mode that allows you to take control and manually begin charging dead batteries down to zero volts.
• Automatically detects battery sulfation and acid stratification to restore lost battery performance for stronger engine starts and extended battery life.
• It's not just a trickle charger; it's an advanced battery maintainer. A fully automatic, worry-free battery charger for everyday use - 24/7 - with zero overcharge.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

The Precision Raceworks G8x/G2x Stand Alone Auxiliary Fuel System is the highest-performing and most stable low-pressure fuel system on the market! Forget about how things have been done and embrace the benefits of dedicated fueling for your port injection!

Since direct injection came out for BMW, enthusiasts have been adding port injection.  With this came the need to upgrade the low-pressure fuel system to keep up.  Historically this was done by increasing the output of the main fuel system.  Unfortunately, the main fuel pump is controlled using PWM by a factory programmed controller designed to reduce output when target fuel pressure (typically 5 bar) is exceeded, creating a constant battle when pumps are added or upgraded.  This limits upgraded fuel pumps from performing to their full potential.

Additionally, the high-pressure pump control system dumps fuel back into the low-pressure system at high pressure low volume resulting in oscillations of the low-pressure fuel system.  Because of this, the DI system in the car is required to constantly make corrections to keep target AFR in check.

With this stand-alone low-pressure fuel system dedicated to your port fueling that is a thing of the past!  Get rock-solid fuel pressures at any pressure, run fuel pressures that are 1:1 scalable to boost pressure, flow more fuel with dedicated lines, run smaller injectors and still get more fuel than you did with large injectors (allowing for higher resolution), put less demand on the car’s DI system to correct for fluctuations in pressure, even your tuner will be grateful as the system makes tuning of port fueling even easier and more accurate, the list of benefits goes on and on!

Features & Benefits

Billet Aluminum top hat with 3 high-flow fuel ports

Dedicated fuel pump(s) for port injection system

Optimal pump location resistant to fuel slosh under acceleration

Fully adjustable 1:1 scaling billet fuel pressure regulator

10-micron USA made Microglass fuel filter (Ideal for E85)

Smooth bore high flow PTFE fuel feed & return lines (AN6)

All billet connections for both fuel line fittings and top-hat

Plug and play connectors inside and outside* the top hat

Configurable pump activation harness (see instructions for more details)

Increased injector flow (when using 1:1 regulator feature vs static)

Compatible with all stock or upgraded primary fuel pumps

Easily expandable and upgrade-able for more fuel

All components and parts feature 100% Ethanol Compatibility

The AFS.745 dedicated auxiliary fuel system comes with all** necessary components to provide dedicated fuel system for port injection.  Featuring One Walbro 450 (F900074)  & One Walbro 535 (F9000295) fuel pumps with a combined flow of 745LPH @ 3bar.

Pump flow 43.5 psi-a : 745 lph

Recommended base pressure: 43.5 psi-g

Maximum Fuel Pressure: 110 psi-g

Number of Fuel Output Ports: 2

Number of Fuel Return Ports: 1

Pump 1: Walbro 535 (F90000295)

Pump 2: Walbro 450 (F90000274)

Available (unused) Electrical Connections: 2*

Total System Weight:14 lbs (including fuel lines and wiring harness)

*At time of install some wiring in the car may need to be cut and spliced to connectors included in this kit

**Male AN8-ORB to Female AN6-ORB adapter may be required for compatibility with some fuel rails (not included in kit)

BMW Washer Fluid Tank Cap - G2X G8X is a premium upgrade that enhances both the appearance and durability of your BMW’s engine bay. Designed as a direct replacement for the factory cap, this precision-engineered component eliminates the flimsy plastic construction and dull blue color, replacing it with a sleek, high-quality billet aluminum design.

Crafted for both style and functionality, this washer fluid cap ensures a secure fit while adding a refined, motorsport-inspired touch to your engine bay. Built to withstand extreme temperatures and chemical exposure, it provides long-lasting performance and a premium aesthetic upgrade.

• Direct replacement for OEM cap – Perfect fit with no modifications required
• High-quality billet aluminum construction – Stronger and more durable than factory plastic
• Enhanced engine bay aesthetics – Adds a sleek and stylish look
• Secure fit and easy installation – Snaps into place just like the original
• Resistant to heat and chemicals – Designed for long-term reliability
• Precision-machined design – Ensures proper function and a premium finish

Upgrade your BMW with a BMW Washer Fluid Tank Cap - G2X G8X, providing both superior durability and a refined appearance.

The Precision Raceworks G8x/G2x Stand Alone Auxiliary Fuel System is the highest-performing and most stable low-pressure fuel system on the market! Forget about how things have been done and embrace the benefits of dedicated fueling for your port injection!

Since direct injection came out for BMW, enthusiasts have been adding port injection.  With this came the need to upgrade the low-pressure fuel system to keep up.  Historically this was done by increasing the output of the main fuel system.  Unfortunately, the main fuel pump is controlled using PWM by a factory programmed controller designed to reduce output when target fuel pressure (typically 5 bar) is exceeded, creating a constant battle when pumps are added or upgraded.  This limits upgraded fuel pumps from performing to their full potential.

Additionally, the high-pressure pump control system dumps fuel back into the low-pressure system at high pressure low volume resulting in oscillations of the low-pressure fuel system.  Because of this, the DI system in the car is required to constantly make corrections to keep target AFR in check.

With this stand-alone low-pressure fuel system dedicated to your port fueling that is a thing of the past!  Get rock-solid fuel pressures at any pressure, run fuel pressures that are 1:1 scalable to boost pressure, flow more fuel with dedicated lines, run smaller injectors and still get more fuel than you did with large injectors (allowing for higher resolution), put less demand on the car’s DI system to correct for fluctuations in pressure, even your tuner will be grateful as the system makes tuning of port fueling even easier and more accurate, the list of benefits goes on and on!

Features & Benefits

Billet Aluminum top hat with 3 high-flow fuel ports

Dedicated fuel pump(s) for port injection system

Optimal pump location resistant to fuel slosh under acceleration

Fully adjustable 1:1 scaling billet fuel pressure regulator

10-micron USA made Microglass fuel filter (Ideal for E85)

Smooth bore high flow PTFE fuel feed & return lines (AN6)

All billet connections for both fuel line fittings and top-hat

Plug and play connectors inside and outside* the top hat

Configurable pump activation harness (see instructions for more details)

Increased injector flow (when using 1:1 regulator feature vs static)

Compatible with all stock or upgraded primary fuel pumps

Easily expandable and upgrade-able for more fuel

All components and parts feature 100% Ethanol Compatibility

The AFS.640 dedicated auxiliary fuel system comes with all** necessary components to provide dedicated fuel system for port injection.  Featuring Two Walbro 450’s (F9000274) fuel pumps with a combined flow of 640LPH at 3 bar.

Pump flow 43.5 psi-a : 640 lph

Recommended base pressure: 43.5 psi-g

Maximum Fuel Pressure: 110 psi-g

Number of Fuel Output Ports: 2

Number of Fuel Return Ports: 1

Pump 1: Walbro 450 (F90000274)

Pump 2: Walbro 450 (F90000274)

Available (unused) Electrical Connections: 2*

Total System Weight: 14 lbs (including fuel lines and wiring harness)

*At time of install some wiring in the car may need to be cut and spliced to connectors included in this kit

**Male AN8-ORB to Female AN6-ORB adapter may be required for compatibility with some fuel rails (not included in kit)

The Precision Raceworks G8x/G2x Stand Alone Auxiliary Fuel System is the highest-performing and most stable low-pressure fuel system on the market! Forget about how things have been done and embrace the benefits of dedicated fueling for your port injection!

Since direct injection came out for BMW, enthusiasts have been adding port injection.  With this came the need to upgrade the low-pressure fuel system to keep up.  Historically this was done by increasing the output of the main fuel system.  Unfortunately, the main fuel pump is controlled using PWM by a factory programmed controller designed to reduce output when target fuel pressure (typically 5 bar) is exceeded, creating a constant battle when pumps are added or upgraded.  This limits upgraded fuel pumps from performing to their full potential.

Additionally, the high-pressure pump control system dumps fuel back into the low-pressure system at high pressure low volume resulting in oscillations of the low-pressure fuel system.  Because of this, the DI system in the car is required to constantly make corrections to keep target AFR in check.

With this stand-alone low-pressure fuel system dedicated to your port fueling that is a thing of the past!  Get rock-solid fuel pressures at any pressure, run fuel pressures that are 1:1 scalable to boost pressure, flow more fuel with dedicated lines, run smaller injectors and still get more fuel than you did with large injectors (allowing for higher resolution), put less demand on the car’s DI system to correct for fluctuations in pressure, even your tuner will be grateful as the system makes tuning of port fueling even easier and more accurate, the list of benefits goes on and on!

Features & Benefits

Billet Aluminum top hat with 3 high-flow fuel ports

Dedicated fuel pump(s) for port injection system

Optimal pump location resistant to fuel slosh under acceleration

Fully adjustable 1:1 scaling billet fuel pressure regulator

10-micron USA made Microglass fuel filter (Ideal for E85)

Smooth bore high flow PTFE fuel feed & return lines (AN6)

All billet connections for both fuel line fittings and top-hat

Plug and play connectors inside and outside* the top hat

Configurable pump activation harness (see instructions for more details)

Increased injector flow (when using 1:1 regulator feature vs static)

Compatible with all stock or upgraded primary fuel pumps

Easily expandable and upgrade-able for more fuel

All components and parts feature 100% Ethanol Compatibility

The AFS.425 dedicated auxiliary fuel system comes with all** necessary components to provide a dedicated fuel system for port injection.  Featuring a single Walbro 450 (F9000274) fuel pump which flows 425LPH at 3 bar.

Pump flow 43.5 psi-a : 425lph

Recommended base pressure: 43.5 psi-g

Maximum Fuel Pressure: 110 psi-g

Number of Fuel Output Ports: 2

Number of Fuel Return Ports: 1

Pump 1: Walbro 450 (F90000274)

Pump 2: N/A

Available (unused) Electrical Connections: 4*

Total System Weight: 11 lbs (including fuel lines and wiring harness)

*At time of install some wiring in the car may need to be cut and spliced to connectors included in this kit

**Male AN8-ORB to Female AN6-ORB adapter may be required for compatibility with some fuel rails (not included in kit)