BMW Tools & Specialty Equipment for BMW G42 M240i xDrive B58 3.0L

PRESSURE BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

FLUID CATCH BOTTLE:

keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

BMW B58 Oil Catch Tool is designed to address the common issue of oil spillage during the removal of the oil filter on BMW B58 engines. This tool helps prevent messes in the engine bay and surrounding areas, making maintenance easier and cleaner.

• Mess-Free Oil Changes: Effectively captures oil spillage during oil filter removal to keep the engine bay clean.
• Precision Design: Clamps securely onto the oil filter housing to prevent oil from reaching hard-to-clean areas.
• Durable Construction: Made in the USA from high-quality materials for long-lasting performance.
• Enhanced Safety: Reduces the risk of burns and cuts associated with cleaning oil from tight spaces.

BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

Includes:

• 3 Liter (3.17 qts) storage tank
• Pressure cap with 0-30 lb gauge and pressure relief valve
• 40" hose
• Dual preventative fittings on the hose, featuring a chrome quick coupler on one end to snap onto the master cylinder cap and a detachable swivel fitting on the other end

Note:

• Recommend working at 10 PSI
• Dimensions for cap seal: 12x21x4 mm
• LIFETIME REPLACEMENT

CATCH BOTTLE:

Keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

CALIPER HOOK SET:

Tired of messing with bent coat hangers or bungee cords to hang your calipers up and out of the way when performing brake maintenance? These hooks make working on your brakes easier by letting you hang your calipers with ease, no more fighting with the bungee cords or zip ties to hold the caliper just right or having to make your own "custom" hooks with wire.

• Holds brake calipers out of the way while working on brakes
• Also use to hang other automotive parts and tools while working on your vehicle.
• Stronger than zip ties or wire.
• Save the brake hose by not hanging caliper by hose.
• Made of  thick steel for strength and durability. length is 8"

BILLET ALUMINUM CAP:

This aluminum cap with 90 degree swivel will work with our T#363245 Euro bleeder or our T#366970 3-Liter Multi-functional Fluid Pump Kit.

Features an all aluminum 45mm cap with quick coupler nipple.

BLEEDER WRENCH:

Finally, a bleeder wrench with just the right angle to open the bleeder screw without having to spend all that time removing each wheel from your car.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

46 PIECE SET:

This 1/4" set contains all the most popular tools needed to get the job done on your European car repair.

Kit Contains:

-13PCS-1/4" DR.6PT SOCKETS: 4, 4.5 , 5 ,5.5 ,6 , 7, 8 ,9 ,10, 11, 12, 13, 14MM 

-1PC- 1/4" DR. QUICK RELEASE RATCHET (72T).

-2PC- 1/4" DR.50 & 100MM EXTENSIONS 

-1PC- 1/4" DR.150MM FLEXIBLE EXTENSION

-1PC- 1/4" DR.UNIVERSAL JOINT

-1PC- 1/4" DR.SLIDING T-BAR

-1PC- 1/4" DR.6" SPINNER HANDLE

-1PC- 1/4" DR.1/4" BIT HOLDER ADAPTER

-4PCS-HEX KEY WRENCHES:1.27, 1.5,2,2.5MM

-6PCS-1/4" HEX SOCKETS:3,4,5,6,7,8MM

-3PCS-1/4' SLOTTED SOCKETS:4,5.5,7MM

-3PCS-1/4" PHILIPS SOCKETS:PH1, PH2, PH3

-3PCS-1/4"POZI SOCKETS: PZ1, PZ2, PZ3

-6PCS-1/4" TORX SOCKETS: T10, T15, T20, T25, T30, T40

TRIM/MOLDING SET:

Plastic five-piece tool kit removes trim and door panels, moldings, and adhesive backed logos and badges, without damage.

Made of impact resistant plastic that will not mar surfaces as metal screwdrivers and pry bars will. Slim design for delicate work in tight areas.

Kit includes:

• Wide edge remover

• Narrow edge remover

• Pull-type remover

• Handle remover

• Upholstery clip remover

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Due to clearance issues, many types of lifts require specific adapters that are made for reaching SUV and truck jack points. This 12-piece kit has been made by using stackable adapters that mount inside the lifting block trays so that vehicles with high ground-clearance or those with unique jack point locations are better accommodated. These adapters offer up to 7.2" of additional height when all combined.

Complete kit includes:

• Low‐profile round polyurethane contact pads  -  Qty: 4
• Sliding receivers that accommodate the round polyurethane contact pads and/or the stackable adapters  -  Qty: 4
• 3" stackable adapters.  -  Qty: 4

Fits BL-5000SLX/EXT and BL-7000SLX/EXT Series Only.

EXTRACTOR:

The Schwaben 6.5 Liter Extractor empowers you with swift, hand-operated fluid extraction. Complete with two tubes of varying diameters to suit your unique needs, this system's vacuum release button guarantees seamless operation. Clearing 6.5 Liters (6.8 qts.) of fluid in minutes, it preserves a spotless, oil-free workspace. Its ingeniously designed pour spout ensures mess-free fluid disposal.

Features:

• Stability First: Equipped with a flip-out foot for steady usage, delivering precise extraction.
• Organized Efficiency: Integrated hose storage streamlines your extraction process.
• Perfectly Sized: A 41" main tube (3/8" OD) and two 35" extension tubes (1/4" and 3/16" OD) ensure versatility across applications.
• Beyond Extraction: It doubles as a brake bleeder with the optional ES3248036 Brake Bleeder Hose.
• LIFETIME REPLACEMENT: Like almost all Schwaben tools, this fluid extractor is backed by our lifetime replacement program should anything go wrong!

ADAPTER:

This adapter hose allows a quick and easy suction thru the bleeder screw. This hose has included shut off valve in hose.  This will improve your extractor capabilities and make it even more of an all-in-one tool!

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Male & female quick-connect fittings conveniently connect the leader hoses to the long hoses, making it easy to assemble and disassemble QuickJack after the simple one-time setup.

Each flush-face, zero-leak fitting is designed to prevent hydraulic oil or ATF from leaking, ensuring your frames function properly at all times.

Male fitting does NOT attach to QuickJack power unit.

Compatible with all SLX and TL models.

Looking for the best of the best in your search for a floor jack? AC Hydraulic's DK20Q Hydraulic Floor Jack is the answer. This jack is built to take anything you can throw at it and keep on going. Using a wide and robust high-strength steel frame, blue powedercoat paint protection, and built-in safety overload valve, this jack was designed in mind to outlast us all!

Features:

• Very low minimum height of only 3.15 inches
• Wide and robust frame made of high-strength steel
• Precise and safe control whilst lowering
• Manual dead man’s release for optimum safety when lowering
• Built-in safety overload valve
• Noiseless wheels incorporating a polyurethane central O ring offers maximum surface protection
• Ergonomically designed handle ensuring positive and safe operation
• DK20Q is fitted with quick-lift pedal for easy reach of lifting point

Specifications:

• Capacity:  4400 lbs
• Min. height:  3.15 inches
• Max. height:  19.49 inches
• Frame length:  25.98 inches 
• Handle length:  37.40 inches
• Frame height:  6.30 inches 
• Width:  16.14 inches
• Weight:  68 lbs

• Tough and rigid expanded polystyrene foam (EPS) with a load rating of 1,500lbs per wheel (almost twice what the normal corner weight would be on a 3-series BMW)
• 10" height X 12" width with minimal compression under load
• Light weight with each block weighing less than 6lbs and with a handy strap for carrying or hanging
• Curved cradle for the tire to sit inside
• Non-skid surface that won't scratch your floor

Looking for an alternative to your jack stands? With these wheel blocks you won't have to think twice about a jack stand scratching or denting the underside of your floor or the car falling off the jack stand. These work best when used with a floor jack under the subframe and the opposite axle wheels chocked. These are also a light weight and inexpensive alternative to the super-pricey plastic and metal ramps. They are resistant to most fluids and chemicals (but not solvents) and will never rust unlike metal ramps and blocks.

Also available in a 12" height.