BMW Tools & Specialty Equipment for BMW G80 M3 S58 3.0L

This tool comes in handy especially when working with an engine harness. Certain areas are always prone to corrosion and this tool makes having to re-pin a connector a breeze.

Unlike small screwdrivers, picks, and paper clips, these tools are the correct size and shape to remove and install tiny electrical pins and terminals at plastic block connectors with ease, and will not damage the connectors in the process.

Packaged in a blow molded case to keep everything secure and organized.

This professional-grade deluxe fender roller allows you to gently and gradually flatten your inner fender lips in order to increase your fender to tire clearance.

This new deluxe fender roller has been designed to fit most applications.

This is the perfect tool for:

If you want to lower your vehicle
If you want wider-than-stock wheels
If you are going to use wheel spacers or decreased offset
Will work with bolt patterns of 4x100 and 5x100 up to 4x114.3 and 5x130 with 12mm or 14mm lug bolts.

By rolling the fender lip flat, you can lower your car further, and give your car a wider stance, without your tires rubbing on the inside of the fender.

Fully adjustable for use on vehicles of different ride heights, offsets, and wheel bolt patterns.

Use of a heat gun is recommended to soften the fender surface during the rolling process and prevent paint cracking.

When doing work where the mounts and support need to be removed from the engine or transmission having a engine support bar is wise. By using this engine support the stress is coming off of whatever components are still attached reducing future unnecessary repairs. The safety side of it is having the heavy engine and transmission firmly supported as it should be instead of questionable jack techniques.  

Features:

•  2" longer than most
•  Two angle chain hooks for safer and more stable chain support 
•  61" long and fully adjustable to any width
•  Weight rating is a full 1000 lbs.
•  Includes four rubber padded feet to prevent slipping and damage to cars finish 
• This tool features a dual hook design for holding engine or transmission in place
•  Powder coated for long life and durability

Note: It is important that chains are hooked to both sides of hook, like in photo to insure load is supported evenly. 

Looking to update your old torque wrenches? The Schwaben 3/8" Drive Digital Torque Wrench is your answer. 

This digital torque wrench uses an easy-to-read display to show torque amounts and settings, features a push button release, reversible 3/8" drive, 45 tooth ratchet head, and a comfortable no-slip grip and adjustment wheel.

Specifications:

• Setting Range: 45-220 ft lbs (60-300 Nm)
• Display Units: ft-lbs, N-m, Inch-lbs, cm-kg2, and m-kg
• Size: 22" (550mm) length for easy leverage
• Accuracy: +- 3%
• Include blow molded holding case
• Requires one 3V CR2030 battery (included)

 This comprehensive kit is basically a one-stop-shop to pick up all the special torx, triple square, & hex bits you need to keep your car where it should be... on the road!

This Universal European Tool Kit features the following:

• Torx Screwdriver Kit - 6 Pieces (Sizes included: T10, T15, T20, T25, T27, & T30. Perfect for removing door and dashboard panels, interior trim, and smaller underhood components. )
• Swivel Head Triple Square Driver Kit - 4 Pieces (Set of four 3/8 drivers in M6, M8, M10, and M12 sizes. Perfect for working around corners in those hard to reach spots.)
• Specialty Bit Kit - 100 Pieces (100 piece torx & hex bit kit to fit a wide assortment of automotive fasteners. Made of hardened Chrome Vanadium steel, packaged in a handy blow molded case.)
• Go-Through Screwdriver Kit - 6 Pieces (Kit includes durable slotted & phillips head nickel-chromoly screwdrivers with hardened shafts that extend the entire length of the driver.)

If you're refreshing your struts and springs this tool is a must, properly compress the springs, easily remove and install the strut nut, and smoothly remove the spindles.

Features:

• Spring Compressor
• Strut Nut Sockets
• Spindle Spreader

BMW essentials from drivetrain work to fluid changes.

Features:

• 36mm 12-point deep socket, 1/2" drive - Used on axle nuts and most BMW oil filter housing nuts
• 30mm 12-point deep socket, 1/2" drive - Used on driveshaft and pinion mounting, rear wheel bearing removal and reinstallation on many BMWs
• 27mm 6-point socket, 1/2" drive - Fits N52/54 oil filter housing nuts and other various places on most BMWs
• 14/17mm service wrench - Versatile wrench features an open end and a hex head driver that fit most BMW transmission fill/drain plugs. Perfect for engine and transmission oil drains.
• M18 triple square extended reach socket, 1/2" drive - Used to remove axles and other various driveline components.
• All of the sockets included in this kit are built with extreme durability and versatility in mind, and can be used with breaker bars and impact guns.

The CTA7880 revolutionizes control arm bushing tasks, ensuring effortless removal and installation. This tool simplifies the process by enabling work without removing the arm, saving time and effort. Its unique design securely holds and compresses new bushings, seamlessly pressing them into the suspension control arm for a precise fit. Engineered with precision and convenience, it's a must-have for mechanics and DIY enthusiasts. Upgrading your vehicle's bushings has never been this efficient. Trust in its reliability and ease of use, ensuring a hassle-free bushing replacement process. Plus, our LIFETIME REPLACEMENT program guarantees your satisfaction, making it the ultimate choice for professionals and enthusiasts alike.

• Works without removing the arm, saving time and effort
• Securely holds and compresses new bushes for precise installation
• LIFETIME REPLACEMENT