VTT Single Piece Silicone Charge Pipe w/o BOV - B58

2X Entries Into Our F80 M3 Sweepstakes

T#:21209815

Part#: VTT-A90CP

Ships in 10 Business Days

Starting at $ 345.99 USD

Add to Wish List

Starting at $ 345.99 USD

Add to Wish List

6-ply, Heat Resistant, Wire reinforced silicone charge pipes rated at over 200 psi This system completely does away with the restrictive, and muli-connection stock charge pipe system, and replaces it with a single 6-ply, Heat Resistant, Wire reinforced silicone charge pipes rated at over 200 psi. They are molded for the perfect fit in your engine bay, while not sacrificing anything in the way of flow or size. They also completely isolate your charge air from any additional heat soak coming in from the engine or ambient heat. Another huge benefit is your vehicle goes from 4 connections to only TWO which are barbed and has many small ridges which dig into the silicone so it’s impossible for the pipe to blow off. This means no more blown charge pipe connections on the track or road leaving you stranded. There are other options on the market, but they only address the problem in half measures. Some offer silicone connectors that are attached to hard pipes and are notorious for blowing, but they do nothing to address the heat soak issue or the number of connections needed. This kit solves ALL of those problems and does so at a lower cost. Install is very easy and takes about an hour if you are inexperienced with working on your own car, can take as little as 30-45 minutes if you have had it apart a few times. Dimensions for the pipes are as follows: Hot Side Pipe: 64mm or 2.50' on the connection to the turbo outlet opening up immediately to 77mm or 3' and remaining a FULL 3' to the throttle body inlet. Note: These will fit all aftermarket manifolds BMS has tested, some require slight trimming of the 3' end The kit includes: VTT Hot Side Silicone Charge pipe 2 VTT Branded CNC adapters to mount the map sensor, and Temp Probe 2 VTT Branded CNC adapters for the Turbocharger outlet, and TB inlet 2 VTT branded T-Bolt Clamps 2 1/8 NPT ports are included in the TB flange for methanol

Show More Show Less

AFE Track Series Carbon Fiber Cold Air Intake System W/ Pro 5R Filter...

T#:5677368

Part#: 57-10017R

Ships in 3 Business Days

$ 750.00 USD

Add to Wish List

Qty

$ 750.00 USD

Add to Wish List

Features: Dyno-Proven Gains up to +26 HP & +27 Lbs. x Ft. TQ Outflows Factory Intake by 53% Measured Flow: 505 CFM @ 7” H20 Lightweight, 100% Carbon Fiber Intake Tube Open-Element Design Showcases the Air Filter and Delivers an Aggressive Air Intake Sound Washable and Reusable Pro 5R Air Filter for Maximum Performance Innovative Filter-to-Housing Interface and Minimal Hardware for Fast & Easy Installation Utilizes Factory Mounting Locations for an Easy and Secure Installation Fits With Factory and aFe CONTROL Strut Bar Large Three Layer Performance Air Filter: This 7” tall 360-degree radial flow air filter features a 4” oval flange and our oiled Pro 5R media with five layers of progressively finer cotton gauze media for maximum airflow and performance. This media is best suited for street and track use. Unique One-Piece Housing: The included massive air filter is surrounded by an open-element XLPE (cross-linked polyethylene) polymer housing that minimizes warm engine air for maximum performance. Its open design allows for easy viewing of the air filter and delivers an aggressive air intake sound. Dyno-Tuned Intake Tube: The lightweight tube is computer-designed to achieve maximum power gains while maintaining a perfect fit. Manufactured from 100% twill weave carbon fiber, it features zero fiberglass and is clear-coated for the highest quality construction. Hassle-Free Installation: This intake is designed to use factory mounting locations, minimizing the use of unnecessary hardware, ensuring a perfect fit every time. Its revolutionary design, featuring our patent pending filter-to-housing interface uses half the number of parts of a traditional cold air intake system. Premium Components: Stainless-steel clamps are included for strength, and a premium bellows coupling allows for ample flexibility. Fitment Note: This intake is designed to fit models equipped with the factory strut brace, with no modification required. Emissions Disclaimer: This product is not currently CARB exempt and is not available for purchase in California or for use on any vehicle registered with the California Department of Motor Vehicles.

Show More Show Less

Injen SP Cold Air Intake System - Wrinkle Black - G29 Z4, A90 MKV Sup...

T#:26705012

Part#: SP2300WB

In Stock at Vendor

$ 459.99 USD

Add to Wish List

Qty

$ 459.99 USD

Add to Wish List

The all-new 2020-2023 Toyota GR Supra and the BMW Z4 equipped with the B58 3.0L turbo engine are beasts from the factory, so the engineers at Injen Technology needed to design an intake that packed a serious punch to keep up with this athletic and sophisticated performer. The R&D team took these all-new rockets deep into the lab to extract the hidden power lurking under the hood. From start to finish, each aspect of Injen Technology’s traditional aluminum Cold Air Intake for the 2020-2023 Toyota GR Supra and BMW Z4 was a true labor of love. The Injen SP2300 cold air intake has the cleanest installation on the market that is also available in multiple finishes for that personized look. The OE intake tract on the B58 engine is very restrictive from the factory and limiting power output by choking the turbo. Our new SP2300 short ram cold air intake opens up that intake tract with a large 4.0" aluminum intake tube that allows that turbo and engine to breathe deep and produce the power that you’ve been craving. The SP series of cold air intakes is Injen’s flagship system in their lines of traditional aluminum cold air intake systems. It provides an intake growl that will surely excite your senses as you open up your Toyota Supra and let that turbo spool. The soul of this intake is found within 6061-T6 aluminum air intake tube that provides a smooth uninterrupted path for highly efficient airflow. Our engineers have painstakingly designed the intake to provide the highest levels of safe power, along with clean aesthetics that will impress every time you open your hood. In addition to the impressive power increase, the Injen team has ensured that a safe Air fuel (A/F) ratio has been maintained throughout the power band. Additionally, the SP2300 intake includes a fully serviceable Injen SuperNano-Web dry air filter, which provides increased filter surface area allowing for greater airflow and unbeatable filtration. If that's not enough, the Injen SP performance intake provides power you can hear and feel! On our dyno, the SP2300 put down an impressive 15 additional horsepower and 17 pound-feet of tire-scorching torque! KEY FEATURES Dyno Proven gains of up to 15 hp and 17 lb.-ft. of torque Aggressive engine tone under full throttle Provides power gains while maintaining A/F ratios – no additional tuning required Massive 4.00 6061-T6 aluminum intake tubing Smooth intake piping eliminates restrictions and improves airflow Includes custom heat shield specifically designed for this application Aggressive under-hood appearance while maintaining an OE fit Fully serviceable Injen SuperNano-Web dry air filter Available in Polished, Wrinkle Black, and Wrinkle Red Made in Pomona California, USA Injen Technology Limited Lifetime Warranty

Show More Show Less

Injen SP Cold Air Intake System - Polished - G29 Z4, A90 MKV Supra B5...

T#:26705011

Part#: SP2300P

In Stock at Vendor

$ 459.99 USD

Add to Wish List

Qty

$ 459.99 USD

Add to Wish List

The all-new 2020-2023 Toyota GR Supra and the BMW Z4 equipped with the B58 3.0L turbo engine are beasts from the factory, so the engineers at Injen Technology needed to design an intake that packed a serious punch to keep up with this athletic and sophisticated performer. The R&D team took these all-new rockets deep into the lab to extract the hidden power lurking under the hood. From start to finish, each aspect of Injen Technology’s traditional aluminum Cold Air Intake for the 2020-2023 Toyota GR Supra and BMW Z4 was a true labor of love. The Injen SP2300 cold air intake has the cleanest installation on the market that is also available in multiple finishes for that personized look. The OE intake tract on the B58 engine is very restrictive from the factory and limiting power output by choking the turbo. Our new SP2300 short ram cold air intake opens up that intake tract with a large 4.0" aluminum intake tube that allows that turbo and engine to breathe deep and produce the power that you’ve been craving. The SP series of cold air intakes is Injen’s flagship system in their lines of traditional aluminum cold air intake systems. It provides an intake growl that will surely excite your senses as you open up your Toyota Supra and let that turbo spool. The soul of this intake is found within 6061-T6 aluminum air intake tube that provides a smooth uninterrupted path for highly efficient airflow. Our engineers have painstakingly designed the intake to provide the highest levels of safe power, along with clean aesthetics that will impress every time you open your hood. In addition to the impressive power increase, the Injen team has ensured that a safe Air fuel (A/F) ratio has been maintained throughout the power band. Additionally, the SP2300 intake includes a fully serviceable Injen SuperNano-Web dry air filter, which provides increased filter surface area allowing for greater airflow and unbeatable filtration. If that's not enough, the Injen SP performance intake provides power you can hear and feel! On our dyno, the SP2300 put down an impressive 15 additional horsepower and 17 pound-feet of tire-scorching torque! KEY FEATURES Dyno Proven gains of up to 15 hp and 17 lb.-ft. of torque Aggressive engine tone under full throttle Provides power gains while maintaining A/F ratios – no additional tuning required Massive 4.00 6061-T6 aluminum intake tubing Smooth intake piping eliminates restrictions and improves airflow Includes custom heat shield specifically designed for this application Aggressive under-hood appearance while maintaining an OE fit Fully serviceable Injen SuperNano-Web dry air filter Available in Polished, Wrinkle Black, and Wrinkle Red Made in Pomona California, USA Injen Technology Limited Lifetime Warranty

Show More Show Less

A90 Supra Experience Package

Call In Or Chat For Best Price! 10X Entries Into Our F80 M3 Sweepstakes

T#:30197980

Part#: A90-SUPRA-E-B

Ships on Oct 26, 2026

Sale - Save 10% $ 2,467.99

This product was last offered at the strikethrough price on
09-29-2026

$ 2,220.82 USD

Add to Wish List

Qty

Sale - Save 10%

$ 2,467.99

This product was last offered at the strikethrough price on
09-29-2026

$ 2,220.82 USD

Add to Wish List

Going beyond its Foundation counterpart, the Dinan Experience packages address not only the engine but also the chassis for a complete solution in the form of a wholly tuned Dinan vehicle. While adding power modifiers is often the go-to path when beginning the modification journey, it does not fully consider what makes the car infinitely more enjoyable in scenarios outside of WOT pulls. With the addition of suspension upgrades integrated alongside the power adders, the vehicle is transformed into something more than just the sum of its parts. It's a comprehensive answer to delivering additional technical capabilities in the form of increased engine performance and better handling along with improvements to aesthetics (looks and sound) in a package designed with reliability and safety in mind. This union of power and handling modifications results in a true OEM+ experience - the Dinan Experience. Includes Dinan Exhaust Dinan Intake Dinan Turbo Inlet Strut Braces Throttle Booster Dinan Badge Features Smiles per gallon instantly multiplied Guaranteed component compatibility and seamless integration 10% price savings when compared to buying the same components a la carte Maximum gains of +13 HP and +14 lb-ft of torque (Exhaust +Intake) Smoother, louder and sportier sound (Exhaust + Intake + Turbo Inlet) Computer-controlled exhaust valves are retained and limit noise during low-speed driving and open fully during high-load conditions (Exhaust) Deletes resonator between the catalyst and rear muffler for increased volume (Exhaust) 10 pounds lighter than the stock for an improved power-to-weight ratio (Exhaust) Reduced intake restriction for greater flow that allows increased turbo efficiency and greater power potential on modified builds (Intake + Turbo Inlet) Improved throttle response (Intake + Turbo Inlet) Increased chassis rigidity with decreased flex during cornering for improved handling and performance (Strut Braces) Customizable throttle mapping for enhances feel and acceleration (Throttle Booster) Every Experience Package instantly qualifies for the Fabled Dinan deck lid badge Includes Dinan Exhaust Dinan Intake Dinan Turbo Inlet Strut Braces Throttle Booster Dinan Badge Features Smiles per gallon instantly multiplied Guaranteed component compatibility and seamless integration 10% price savings when compared to buying the same components a la carte Maximum gains of +13 HP and +14 lb-ft of torque (Exhaust +Intake) Smoother, louder and sportier sound (Exhaust + Intake + Turbo Inlet) Computer-controlled exhaust valves are retained and limit noise during low-speed driving and open fully during high-load conditions (Exhaust) Deletes resonator between the catalyst and rear muffler for increased volume (Exhaust) 10 pounds lighter than the stock for an improved power-to-weight ratio (Exhaust) Reduced intake restriction for greater flow that allows increased turbo efficiency and greater power potential on modified builds (Intake + Turbo Inlet) Improved throttle response (Intake + Turbo Inlet) Increased chassis rigidity with decreased flex during cornering for improved handling and performance (Strut Braces) Customizable throttle mapping for enhances feel and acceleration (Throttle Booster) Every Experience Package instantly qualifies for the Fabled Dinan deck lid badge

Show More Show Less

Forge Silicone Vacuum Hoses

T#:558490

Part#: FORGEVAC

In Stock

Starting at $ 14.99 USD

Add to Wish List

Starting at $ 14.99 USD

Add to Wish List

Car suffering from vacuum leaks? Choose from a 4mm, 5mm, or 6mm diameter vacuum hose from Forge to fix your leak and bring your BMW back to life.

FTP High Flow Air Filter - A90 Supra

T#:5788174

Part#: GA90

Special Order: No Guaranteed ETA

$ 55.00 USD

Add to Wish List

Qty

$ 55.00 USD

Add to Wish List

FTP air filters are made with a durable rubber, with optimum adhesion characteristics to ensure fitment to all shapes of boxes. These air filters are also created without welded joints creating a one piece air filter, increasing durability. Features: Reduced emissions and increased MPG Direct fitment Extends engine life Increased power and airflow

Show More Show Less

3" To 2.5" Silicone Coupler 3" Length

10X Entries Into Our F80 M3 Sweepstakes

T#:363896

Part#: 003402ECS04A-02

Special Order: No Guaranteed ETA

Sale - Save 10% $ 9.99

This product was last offered at the strikethrough price on
06-13-2026

$ 8.99 USD

Add to Wish List

Qty

Sale - Save 10%

$ 9.99

This product was last offered at the strikethrough price on
06-13-2026

$ 8.99 USD

Add to Wish List

3" To 2.5" Silicone Coupler 3" Length

Enhance the performance and durability of your BMW or MINI with the 3" To 2.5" Silicone Coupler 3" Length. This silicone coupler provides a reliable connection between components, ensuring optimal airflow and reducing the risk of leaks. Engineered for durability and heat resistance, it withstands high temperatures and harsh conditions. Upgrade your BMW or MINI with this premium silicone coupler for improved performance.

Reliable connection for optimal airflow
Reduces the risk of leaks for enhanced performance
Engineered for durability and heat resistance
Fits both BMW and MINI models

Show More Show Less

MMX Performance High Flow Cotton Panel Air Filter - G2X G42 B46/B48 B...

T#:22361047

Part#: MMR01-1701

Special Order: No Guaranteed ETA

$ 102.99 USD

Add to Wish List

Qty

$ 102.99 USD

Add to Wish List

Looking for a simple, warranty-friendly upgrade for your car? One of the easiest and best ways to upgrade the breathing abilities of the latest BMW G-Series with 2.0 B48/B46 4-cylinder and 3.0 turbo B58TU 6-cylinder engines is with an MMX replacement performance panel air filter. Allow your engine to breathe better and operate more efficiently – and so improve the engine’s airflow, and power and fuel economy gains will follow. By removing the inevitable restrictions that the standard paper panel filter gives, MMR's Panel Filter allows a small but worthwhile increase in airflow through to the turbo. MMR has developed our own range of MMR performance cotton gauze filters that easily drop into the OE airbox which provide excellent filtration properties, combined with instant performance increases and induction noise enhancements. MMR's tests have shown that it can deliver an additional 15NM of torque on a standard B58 engine. A small but worthwhile difference. Meanwhile, OEM standards of design, quality, materials, and construction mean it fits like a factory part; and lasts like a factory part. This filter is applicable for a wide range of G-Series cars - covering all of the 2.0 4-cylinder and 3.0 6-cylinder versions in these vehicles. FEATURES Increased engine performance Improved induction noise Designed to be used with the OE air filter housing Easily fitted and completely washable. Once fitted this product will last the lifetime of your engine

Show More Show Less

4MM Silicone Vacuum Hose - Black - 9 Feet

T#:370919

Part#: VC04B

In Stock

$ 14.99 USD

Add to Wish List

Qty

$ 14.99 USD

Add to Wish List

Car suffering from vacuum leaks? This vacuum hose has a 4mm inner diameter.

AFe Power Takeda Momentum Cold Air Intake System - Pro 5R Filter - To...

For 2021+ model years only

T#:3283357

Part#: 56-70050R

Back Ordered

$ 435.00 USD

Add to Wish List

Qty

$ 435.00 USD

Add to Wish List

DETAILS: Dyno-Proven Gains up to +14 HP & +22 Lbs. x Ft. TQ Outflows Factory Intake by 16% Measured Flow: 370 CFM @ 7” H20 Washable and Reusable Pro 5R Air Filter for Maximum Performance Clear Sight Window for Convenient Filter Inspection Without Disassembly Innovative Filter-to-Housing Interface and Minimal Hardware for Fast & Easy Installation Utilizes Factory Mounting Locations for an Easy and Secure Installation Fits With Factory and aFe CONTROL Strut Bar Large Five Layer Performance Air Filter: This 7-1/2” tall 360-degree radial flow air filter features a 4” round flange and our oiled Pro 5R media with five layers of progressively finer cotton gauze media for maximum airflow and performance. This media is best for street and track use. Unique One-Piece Housing: The smooth one-piece sealed housing, constructed of heat-resistant XLPE (cross-linked polyethylene) polymer, features our patent-pending filter-to-housing interface. A large, clear sight window allows for hassle-free filter inspection, without having to disassemble your system. Toyota Strut Brace: The Takeda intake is designed to fit with the factory and aFe CONTROL strut brace, with no modifications necessary. Dyno-Tuned Intake Tube: This system features a high quality, computer-designed, dyno-tuned intake tube to achieve maximum power gains while maintaining a perfect fit. Its XLPE material is heat-soak resistant and extremely durable. Hassle-Free Installation: This intake is designed to use factory mounting locations, minimizing the use of unnecessary hardware, ensuring a perfect fit every time. Its revolutionary design, featuring our patent pending filter-to-housing interface uses half the number of parts of a traditional cold air intake system. Premium Components: Premium stainless steel clamps and flexible silicone couplings are used for strength and durability while also providing the most secure installation available. Emissions Disclaimer: This product is not currently CARB exempt and is not available for purchase in California or for use on any vehicle registered with the California Department of Motor Vehicles.

Show More Show Less

AFE Takeda Stage-2 Cold Air Intake System W/Pro 5R Filter

T#:5677369

Part#: 56-10015R

Ships in 3 Business Days

$ 387.00 USD

Add to Wish List

Qty

$ 387.00 USD

Add to Wish List

Feautures: Dyno-Proven Gains up to +26 HP & +27 Lbs. x Ft. TQ Outflows Factory Intake by 53% Measured Flow: 505 CFM @ 7” H20 Open-Element Design Showcases the Air Filter and Delivers an Aggressive Air Intake Sound Washable and Reusable Pro 5R Air Filter for Maximum Performance Innovative Filter-to-Housing Interface and Minimal Hardware for Fast & Easy Installation Utilizes Factory Mounting Locations for an Easy and Secure Installation Fits With Factory and aFe CONTROL Strut Bar Large Three Layer Performance Air Filter: This 7” tall 360-degree radial flow air filter features a 4” oval flange and our oiled Pro 5R media with five layers of progressively finer cotton gauze media for maximum airflow and performance. This media is best suited for street and track use. Unique One-Piece Housing: The included massive air filter is surrounded by an open-element XLPE (cross-linked polyethylene) polymer housing that minimizes warm engine air for maximum performance. Its open design allows for easy viewing of the air filter and delivers an aggressive air intake sound. Dyno-Tuned Intake Tube: The tube is computer-designed to achieve maximum power gains while maintaining a perfect fit. Its XLPE material is heat soak resistant and extremely durable. Hassle-Free Installation: This intake is designed to use factory mounting locations, minimizing the use of unnecessary hardware, ensuring a perfect fit every time. Its revolutionary design, featuring our patent pending filter-to-housing interface uses half the number of parts of a traditional cold air intake system. Premium Components: Stainless-steel clamps are included for strength, and a premium bellows coupling allows for ample flexibility. Fitment Note: This intake is designed to fit models equipped with the factory strut brace, with no modification required. Emissions Disclaimer: This product is not currently CARB exempt and is not available for purchase in California or for use on any vehicle registered with the California Department of Motor Vehicles.

Show More Show Less

3MM Silicone Vacuum Hose - Red - 9 Feet

T#:370915

Part#: VC03R

In Stock

$ 14.99 USD

Add to Wish List

Qty

$ 14.99 USD

Add to Wish List

Upgrade Your BMW with Forge 3MM Silicone Vacuum Hose - Red - 9 Feet

Upgrade your BMW's vacuum system with the Forge 3MM Silicone Vacuum Hose in Red, a high-quality solution designed for optimal performance and durability. This 9-foot silicone vacuum hose provides superior flexibility and resistance to extreme temperatures, making it ideal for various automotive applications. Engineered with precision, it ensures reliable vacuum pressure for efficient engine operation and component functionality. Whether you're replacing worn-out hoses or customizing your BMW's vacuum setup, the Forge Silicone Vacuum Hose offers reliability and performance you can trust.

High-quality silicone construction for durability
Superior flexibility for easy installation
Resistant to extreme temperatures
Ensures reliable vacuum pressure for efficient engine operation
Ideal for various automotive applications

Car suffering from vacuum leaks? This vacuum hose has a 3mm inner diameter.

Show More Show Less

4MM Silicone Vacuum Hose - Blue - 9 Feet

T#:370917

Part#: VC04

Back Ordered

$ 14.99 USD

Add to Wish List

Qty

$ 14.99 USD

Add to Wish List

Car suffering from vacuum leaks? This vacuum hose has a 4mm inner diameter.

BMS Billet Water/Methanol Injection Tank Cap With Safety Check Valve ...

T#:20815185

Part#: BMSWMITC

In Stock

$ 59.00 USD

Add to Wish List

Qty

$ 59.00 USD

Add to Wish List

The Burger Motorsports custom billet Water/Methanol Injection (WMI) cap includes an integrated heavy-duty check valve to let much-needed air in and prevent dangerous WMI vapor/fumes and liquid from getting out! Each cap is CNC machined in the USA from a solid block of billet aluminum, engraved with the BMS logo, and anodized blue for protection. Check valve piston must be lightly lubricated if tank shows signs of vacuum. One drop of penetrating oil or motor oil in the top will keep the check valve operational. Features and Benefits Integrated heavy-duty check valve lets air in but not out Specifically designed to prevent evaporation Keeps vapors inside the tank Made from a solid block of billet aluminum Blue anodizing for corrosion protection Exaggerated grips for easy removal Integrated heavy-duty o-ring Made in the USA

Show More Show Less

1 Gallon Methanol Tank - Clear/White

T#:558165

Part#: 1G-MT-CL

In Stock

$ 30.00 USD

Add to Wish List

Qty

$ 30.00 USD

Add to Wish List

The least expensive option available from BMS, this 1 gallon tank is compact and flexible allowing for a wide range of mounting on any flat vertical surface in the trunk. The tank is clear to allow visually checking the fluid level. Includes a 2-way vented black plastic cap and a compression pump feed fitting. Optional upgraded blue billet water/methanol injection (WMI) cap with 1-way check valve, ES4714530 Features & Benefits Available in clear for visually checking fluid levels 8 mounting holes on the side rails Includes 2-way vented black plastic cap Includes a compression pump feed fitting Made in USA Tank dimensions: L 11" x W 4.5 x H 9"

Show More Show Less

High Flow Water-Methanol Solenoid Upgrade - Quick-Connect Fittings ...

T#:598937

Part#: SNO-40060

Ships in 1 Business Day

$ 73.00 USD

Add to Wish List

Qty

$ 73.00 USD

Add to Wish List

Robust protection for your WMI installation to ensure peace of mind The new and improved Snow Performance Solenoid Upgrade offers 100% safety for all injection systems utilizing a rear mounted reservoir, injection points under vacuum, or installs where injection nozzle is lower than water-methanol reservoir. The solenoid fits in line between the pump and injection point and locks fluid in place when not in use adding safety and peace of mind to any injection system. Can also be used to control a second stage of injection with any VC-50, Stage 3, or MPG-MAX water-meth controller. Features: Robust Methanol Resistant Stainless Steel/Zinc Design High PSI Solenoid Designed to Be Used Between Pump & Injection Point Two Brackets Mounted To Solenoid For Easy Install Pigtail Harnessed Wiring Connections Easy to Read "Flow" Indication 2 Quick Connect Fittings To 1/4" High Temp Nylon Tubing Large 3/16" Orifice For Maximum Flow Through System

Show More Show Less

#4 Water Methanol Nozzle - 4 GPH

T#:13957879

Part#: SNO-N0400

In Stock

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

Boost Cooler Forced Induction Progressive Engine Mount Water-Methanol...

T#:641833

Part#: SNO-20010

In Stock

$ 520.99 USD

Add to Wish List

Qty

$ 520.99 USD

Add to Wish List

Keep BMW boost temperatures in check with the Snow Performance Stage 2 Boost Cooler water methanol injection kit, suitable for all forced induction applications (Supercharged/Turbocharged). This kit enhances performance and cooling, especially beneficial for direct-injected engines, effectively removing carbon build-up on valves.

Suitable for all forced induction applications (Supercharged/Turbocharged)
Simple handheld display for easy injection point adjustment
VC-30 progressive controller with digital display and MAP sensor for precise injection
Adjustable start and full points for optimal engagement
Proportional injection based on boost pressure for accurate delivery
Improves drivability and provides cooling benefits
Recommended for street/strip driven gas forced induction vehicles
OEM approved water methanol injection pump with proprietary heat flange
Extreme Environment 300 PSI UHO pump for durability in elements
100% methanol resistant components for longevity
ACU-SEAL compression fittings for leak-free operation
Increases induction charge density for enhanced performance
Made in the U.S.A. and supports 1,000+ HP

Show More Show Less

Snow Performance Water Methanol Injection Nozzle - 8GPH

T#:17040324

Part#: SNO-N0800

In Stock at Vendor

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

BMS DDP5800 Water/Methanol Injection Pump

T#:20815186

Part#: BMSDDP5800

Ships in 1 Business Day

Starting at $ 120.00 USD

Add to Wish List

Starting at $ 120.00 USD

Add to Wish List

The Burger Motorsports DDP 5800 water methanol alcohol Injection pump is a heavy-duty pump used in all of our BMS Water Injection kits. 200 psi bypass for smooth and high pressure and 1.3 GPM open flow. Made in the USA. Available with built-in quick connect fittings for 1/4" WMI line or with open 3/8" NPT threads if you plan to use braided lines.

Show More Show Less

Red High Temp Nylon Tubing - 20ft

T#:640586

Part#: SNO-8087

In Stock at Vendor

$ 20.99 USD

Add to Wish List

Qty

$ 20.99 USD

Add to Wish List

Water/Methanol Nozzle - 6GPH

T#:21374127

Part#: SNO-N0600

In Stock at Vendor

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

2 Gallon Low Profile Universal Methanol Tank

T#:20946755

Part#: 2G-ULPMT

In Stock

Starting at $ 179.00 USD

Add to Wish List

Starting at $ 179.00 USD

Add to Wish List

Integrated pump mount for a super clean install. This tank allows the pump (sold separately) to mount to the bottom of the tank making for a clean and fast installation. It’s universal and will fit a wide variety of trunk applications. The larger capacity means more time between fill ups. Offered in black for a stealth appearance and in clear to allow visually checking the fluid level. Includes a 2-way vented black plastic cap and a compression pump feed fitting. Compatible with BMS DDP5800 pumps, ES4714512 or ES4714513 Optional upgraded blue billet water/methanol injection (WMI) cap with 1-way check valve, ES4714530 Pump mounts directly to the tank Compatible with all DDP 5800 pumps Super low profile design Available in clear for visually checking fluid levels Available in black for a stealth appearance Includes 2-way vented black plastic cap 4 mounting holes in the feet of the tank Includes a compression pump feed fitting, 2 90 degree push fittings, 9" of methanol line and pump mounting hardware. Made in the USA Tank dimensions: L 15.5" x W 8" x H 8.25"

Show More Show Less

High Flow Water Methanol Check Valve

T#:2317849

Part#: SNO-8CV-QC

In Stock at Vendor

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

N1000 - Snow Performance Water Injection Nozzle

T#:2317846

Part#: SNO-N1000

In Stock at Vendor

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

Water-Methanol Dual Nozzle Upgrade - Quick-Connect Fittings

T#:598936

Part#: SNO-40040

In Stock

$ 41.99

This product was last offered at the strikethrough price on
10-01-2026

$ 38.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 41.99

This product was last offered at the strikethrough price on
10-01-2026

$ 38.99 USD

Limited Qty Sale

Add to Wish List

Low Profile Water-Methanol Nozzle Holder 4AN 90* Elbow

T#:640584

Part#: SNO-809-BRD

In Stock

$ 20.99 USD

Add to Wish List

Qty

$ 20.99 USD

Add to Wish List

Snow Performance Stage 3 Boost Cooler (EFI - Port Injection) - Braide...

T#:21374153

Part#: SNO-310-BRD

In Stock at Vendor

$ 833.99 USD

Add to Wish List

Qty

$ 833.99 USD

Add to Wish List

Water/Methanol Nozzle - 1.5GPH

T#:21374121

Part#: SNO-N0150

Ships in 1 Business Day

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

High Flow Water-Methanol Check Valve 4AN Fittings

T#:21374126

Part#: SNO-8CV-BRD

In Stock

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

14GPH Water-Methanol Nozzle

T#:21374112

Part#: SNO-N1400

In Stock

$ 31.99

This product was last offered at the strikethrough price on
09-29-2026

$ 28.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 31.99

This product was last offered at the strikethrough price on
09-29-2026

$ 28.99 USD

Limited Qty Sale

Add to Wish List

1.25 Gallon Heavy-Duty Universal Methanol Tank

T#:20946761

Part#: 1.25G-UMT-CL

Ships on Oct 26, 2026

$ 69.00 USD

Add to Wish List

Qty

$ 69.00 USD

Add to Wish List

This tank is thicker and stronger than BMS' basic 1-gallon WMI tank. This tank features an easy fill filler nozzle, an anti-starvation reservoir with a pre-threaded bung for the included 90º compression pump feed fitting, a spill-catcher reservoir around the filler cap, a 2-way vented black plastic cap, and is translucent to allow visually checking the fluid level. Optional upgraded blue billet water/methanol injection (WMI) cap with 1-way check valve, ES4714530 Features & Benefits 1.25 Gallon Tank (4.73 Liters) Anti-Starvation Reservoir Easy Fill filler Nozzle Spill-Catcher Reservoir around the filler cap Available in clear for visually checking fluid levels 8 mounting holes on the side rails Includes 2-way vented black plastic cap Includes a 90º compression pump feed fitting Tank dimensions: L 11" x W 4.5 x H 9"

Show More Show Less

Hobb

T#:403482

Part#: ACC-HOBBS

Ships on Oct 26, 2026

$ 55.00 USD

Add to Wish List

Qty

$ 55.00 USD

Add to Wish List

GAS STAGE 3 DIRECT INJECTION WATER METHANOL CONTROLLER

T#:586250

Part#: SNO-60300

Ships in 1 Business Day

$ 416.99 USD

Add to Wish List

Qty

$ 416.99 USD

Add to Wish List

Water-Methanol Dual Nozzle Upgrade Stainless Steel Braided Line ...

T#:21374131

Part#: SNO-40040-BRD

In Stock at Vendor

$ 62.99 USD

Add to Wish List

Qty

$ 62.99 USD

Add to Wish List

High Flow Water-Methanol Solenoid Upgrade - 4AN Fittings

T#:21308462

Part#: 40060-BRD

In Stock

$ 73.00 USD

Add to Wish List

Qty

$ 73.00 USD

Add to Wish List

Robust protection for your WMI installation to ensure peace of mind The new and improved Snow Performance Solenoid Upgrade offers 100% safety for all injection systems utilizing a rear mounted reservoir, injection points under vacuum, or installs where injection nozzle is lower than water-methanol reservoir. The solenoid fits in line between the pump and injection point and locks fluid in place when not in use adding safety and peace of mind to any injection system. Can also be used to control a second stage of injection with any VC-50, Stage 3, or MPG-MAX water-meth controller. Features: 100% Methanol Resistant Stainless Steel Construction Comes with (2) 1/8" NPT to 4AN Fittings & Mounting Hardware Can Be Used With All Snow Performance Water Methanol Injection Kits & Upgrades Highest Flowing Water Methanol Solenoid On The Market U.S.A Made

Show More Show Less

Snow Performance Water Methanol Injection Nozzle - 7GPH

T#:17040323

Part#: SNO-N0700

In Stock at Vendor

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

Constructed out of 100% methanol resistant nickel plating, the patented Hyper-Sonic design spins the fluid to supersonic levels before forcing it through two venturi shaped orifices to create the Hyper-Sonic micron droplet mist that has become the industry leader in water-methanol technology. Complete with a removable 80 micron filter, the Hyper-Sonic nozzle can be cleaned and re-used on any application. To unlock power hidden within your water-methanol injection system replace your nozzles with Hyper-Sonic nozzles today! (1/8" NPT Threads)

Show More Show Less

Water Methanol Controller (Boost) - VC-30

T#:21308475

Part#: SNO-60400

In Stock at Vendor

$ 184.99 USD

Add to Wish List

Qty

$ 184.99 USD

Add to Wish List

Water Methanol Controller (Boost) - VC-30 is a sophisticated progressive controller that includes a digital display and boost sensor for precise water/methanol injection. Designed for BMW vehicles, this controller adjusts the injection rate based on boost pressure, ensuring optimal performance and cooling.

Precision Injection: The VC-30 proportionally injects water/methanol based on boost pressure, providing accurate delivery for cooling and performance improvements.
Adjustable Settings: Features adjustable start and full points for customizable engagement and delivery curves to meet engine requirements.
Enhanced Cooling: Improves drivability and cooling benefits across a wide range, making it especially beneficial for direct-injected engines.
Carbon Build-Up Reduction: Effectively removes 100% of carbon build-up on valves, enhancing engine longevity and performance.
Digital Display: Includes a user-friendly digital display for monitoring and adjusting settings.

Show More Show Less

Burger Motorsport JB4-Compatible Water/Methanol Injection System - N2...

T#:558163

Part#: BMS-WMI

Ships on Oct 26, 2026

Starting at $ 226.99 USD

Add to Wish List

Starting at $ 226.99 USD

Add to Wish List

Looking to make loads of power on pump gas? Enter: water/methanol injection. Regardless if you're tuned for conventional pump gas, E85, or race fuel, use of a properly configured and integrated water/meth system will reduce temperatures, allowing you to make more power than on just conventional fuel alone. Select your engine-specific nozzles (which are standard 1/8" NPT and install in most aftermarket chargepipes), your tank to mount in the trunk, upgraded steel braided lines if you so choose, and some boost juice and you just need a management solution! Optionally, add a BMS FSB for JB4 integration!

Show More Show Less

82040R - Snow Performance Tee Adapter Fitting

T#:2317847

Part#: SNO-82040R

In Stock at Vendor

$ 23.99 USD

Add to Wish List

Qty

$ 23.99 USD

Add to Wish List

Stage 2 Boost Cooler Forced Induction Progressive Engine Mount Water-...

T#:641841

Part#: 20010-BRD

In Stock at Vendor

$ 625.00 USD

Add to Wish List

Qty

$ 625.00 USD

Add to Wish List

Turner Motorsport presents the Snow Performance Stage 2 Boost Cooler Water Methanol Injection Kit, ideal for all forced induction applications, including supercharged and turbocharged BMWs. With its easy-to-use handheld display screen, this kit allows precise control over injection points and can be conveniently mounted for access. The VC-30 progressive controller adjusts water/methanol injection based on boost pressure, providing accurate delivery for improved drivability and cooling benefits. This kit is recommended for street/strip driven gas forced induction vehicles seeking cooling over a wide range, especially beneficial for direct-injected engines to remove carbon buildup on valves. Key benefits include:

Precise injection control for improved performance
OEM-approved water methanol injection pump for durability
100% methanol-resistant components for long-lasting use
Guaranteed leak-free operation with ACU-SEAL compression fittings
Increases induction charge density and fuel octane levels for full power

Show More Show Less

Boost Cooler Stage 3 DI ProLine Water Injection

T#:21308464

Part#: SP10317PRO

In Stock at Vendor

$ 833.99 USD

Add to Wish List

Qty

$ 833.99 USD

Add to Wish List

The Snow Performance Stage 3 Boost Cooler brings 2D mapped water-methanol injection delivery to your DI (direct fuel injected) and forced induction (turbocharged/supercharged) vehicle. The Stage 3 creates a 2Dinjection map based off boost and fuel pressure sensor input to deliver an extremely accurate amount of water-methanol when the engine needs it most. Bringing fuel pressure into the mix allows the injection curve to be extended past specific boost points for greater range/control. None invasive, the Stage3 Boost Cooler controller is designed to mount on the steering column or the dash so no additional gauge pods need to be purchased and functions as a boost gauge, water-meth controller and fuel system monitor all in one! Proven to reduce the air inlet temperature by up to 100 degrees and increase octane by 25points for maximum HP and cooling . Comes with adjustable Stage 3 water-meth controller, 4AN fittings, and stainless steel braided line to mount pump/tank in engine bay of vehicle.

Show More Show Less

High Flow Water Methanol Check Valve (Nylon Line)

T#:21374130

Part#: SNO-8CV

Ships in 6 Business Days

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

Black High Temp Nylon Water Methanol Tubing - 20'

T#:20815165

Part#: SNO-80088

Special Order: No Guaranteed ETA

$ 20.99 USD

Add to Wish List

Qty

$ 20.99 USD

Add to Wish List

Snow Performance 20' Bag High Temp Nylon Water Methanol Tubing 100% Methanol Resistant 800 PSI Burst Rating Black

Billet 100 Micron Water Methanol Filter

T#:21374114

Part#: SNO-38FIL

Special Order: No Guaranteed ETA

$ 61.99 USD

Add to Wish List

Qty

$ 61.99 USD

Add to Wish List

Water/Methanol Injection Hose - 20'

T#:21176944

Part#: BMS-WMI-IL

In Stock

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

E6000 Sealant (.18 Oz)

T#:21374144

Part#: SNO-90001

In Stock

$ 4.99 USD

Add to Wish List

Qty

$ 4.99 USD

Add to Wish List

Water-Methanol Braided SS Line Trunk Mount Upgrade (4AN SS Braided Li...

T#:21308470

Part#: SNO-40012-BRD

In Stock at Vendor

28% off MSRP $ 218.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 156.99 USD

Add to Wish List

Qty

28% off MSRP

$ 218.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 156.99 USD

Add to Wish List

Water-Methanol Braided SS Line Trunk Mount Upgrade (4AN SS Braided Line Systems) is designed to relocate your standard 3QT Snow Performance Water-Methanol Tank or any custom tank to the trunk of your vehicle. This upgrade includes everything necessary to safely move and secure your water-methanol system.

Comprehensive Kit: Includes 15 feet of stainless steel braided line, a high-flow solenoid upgrade, and all required AN fittings.
Durable Construction: Features high-quality, stainless steel braided lines for superior strength and resistance to wear.
Enhanced Performance: Designed to ensure optimal performance and reliability of your water-methanol system when relocated.
Easy Installation: Provides all necessary components for a straightforward trunk mount installation.
Versatile Application: Suitable for moving standard and custom water-methanol tanks to the trunk of any vehicle.

Show More Show Less

BMS Water/Methanol Injection (WMI) Solenoid W/ Filter

T#:21176934

Part#: BMS-WMI-SOL

Ships on Oct 26, 2026

$ 75.00 USD

Add to Wish List

Qty

$ 75.00 USD

Add to Wish List

This solenoid safely stops fluid from flowing into your intake system when WMI is not in use. The solenoid features two 1/8 NPT ports with included compression 1/4 in. hose fittings for a quick leak-free connection. The included filter keeps dirt and debris out of your engine.

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Intake Parts for BMW A90 MKV Supra B58 3.0L

Sub-Categories

3" To 2.5" Silicone Coupler 3" Length

Upgrade Your BMW with Forge 3MM Silicone Vacuum Hose - Red - 9 Feet

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results