The NOCO GBC003 Boost HD Precision Battery Clamps are heavy-duty clamps crafted for use with 12-volt gas and diesel engines. These clamps feature a needle-nose profile, allowing them to fit any shape or size battery terminal, from small terminals in tight spaces to top and side post batteries, as well as large terminal sizes. Their robust and rugged springs ensure maximum current flow with minimal power loss. Additionally, the Boost HD Precision accessory boasts no-melt and smoke-free properties, high current transferability, and reinforced all-metal construction.

Features: 

• Heavy-duty battery clamp designed for both 12-volt gas and diesel engines.
• Needle-nose clamp profile for jump starting hard-to-reach and oversized battery terminals.
• Made from durable, heat stabilized 8 AWG silicone wire that maintains its flexibility in cold weather environments.
• Engineered to efficiently transfer maximum current flow with minimal power loss.
• Compatible with the GB20, GB40, GB50, and GBX45 UltraSafe Lithium Jump Starters.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

BMW N55 S55 37cc Platinum Series Dish Piston Set - 84.5mm Bore is designed for high-performance applications, providing exceptional strength and durability for BMW engines. Turner Motorsport offers this premium piston set to enhance engine reliability and efficiency.

• High-Strength Material: Crafted from 2618 high-strength material for superior durability and performance.
• Quiet Start-Ups: Offset wrist pin design minimizes noise during engine start-ups.
• Premium Pins: Includes a .210” wall Premium Chrome Moly pin (Standard Series) or a .210” wall 9310 alloy pin (Extreme Duty Series) for added strength.
• Pressure Balance Groove: Features a pressure balance groove to improve piston stability and efficiency.
• Valve Accommodation: Designed to accommodate +1mm valve sizes for enhanced engine performance.
• Top-Quality Rings: Comes with premium steel top rings, Napier seconds, and round wire locks for optimal sealing and reliability.
• Recommended Clearance: Piston clearance of .0035” measured .850” from the bottom of the oil ring for precise fitment.

Genuine BMW Solenoid Valve (Solv)
 

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

This item fits the following BMW Chassis:
E70 X5M,E71 X6M,E70 X5,E71 X6,E82,E90,E92,E93,F01,F02,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4 X4,F30,F32,F33,F34,F36,F80 M3,F82 M4,F83

Fits BMW Engines including:
N55,N63,N63N,S55,S63,S63N

This eccentric shaft is a vital component of your BMW's N55 Valvetronic system, responsible for precise control of valve lift. In the N55 engine, the Valvetronic system uses intermediate levers between the camshaft and lifters to adjust valve lift dynamically. These levers are actuated by this eccentric shaft, which is rotated by an electronically controlled motor under the direction of the engine computer.

Eccentric shaft failure is a common issue in N55 engines, often caused by inadequate lubrication due to extended oil change intervals. The most frequent failure occurs when the eccentric shaft gear wears down, leading to disengagement from the motor's worm drive. Symptoms include multiple fault codes, such as P1014 (Shaft Parity Error), P1017 (Shaft Sensor Plausibility), P1023 (Valvetronic Adjustment Range), and P10E1 (Valvetronic System No Travel Detected).

If your BMW is experiencing Valvetronic-related fault codes, a failing eccentric shaft could be the source of the problem. Opt for this premium direct replacement from Bremmen Parts to restore your Valvetronic system's functionality and ensure a durable, high-quality repair.

New DCSS 39/50 High-Performance Pump – F90000295

• Highest flow in-tank brushed fuel pump offering from TI Automotive / Walbro
• No Internal check valve - ideal for racing applications to build oil pressure prior to start-up
• Featuring award-winning DCSS technology
• E85 compatible
• High-pressure relief setting - supports supercharger and turbo applications
• Capable of supporting 900+HP at 60PSI naturally aspirated applications
• Complete Pump and kit combination – TCD495

Fuel: GAS & E85

Horsepower: 900+ at 60PSI, naturally aspirated applications

Over All Pump Length: 131mm

Main Housing Diameter: 39mm

Lower Housing Diameter: 50mm

Fuel Inlet Diameter: 11mm OD

Fuel Outlet Diameter: 11mm OD

Flow Rate: 535LPH at 40psi

Test Voltage: 13.5 Volts