Select Vehicle
BMW
Mini
Create an account to be able to build Wish Lists.
Please ensure your correct model is selected
If your M50, M52, or M54 engine takes a few seconds to build oil pressure after sitting, there's a good chance that your factory oil filter housing drain back valve has failed. Over time, the factory plastic check valve degrades, allowing oil to drain completely out of the housing and back into the oil pan while sitting. Every cold start essentially becomes a dry start, resulting in a loud ticking noise and causing unnecessary wear on your engine's internals.
Unfortunately, BMW does not offer this check valve as a standalone part, forcing you to purchase a costly, complete oil filter housing assembly just to fix one failed plastic component. Thankfully, our team of BMW enthusiasts took note of this common failure mode and designed a permanent, cost-effective fix.
Our Billet Oil Filter Housing Drain-Back Valve is designed as a direct-fit upgrade for your factory oil filter housing. CNC-machined from high-strength billet aluminum, this upgraded valve restores positive sealing to keep the oil filter housing fully primed. Maintaining this hydraulic prime ensures rapid oil pressure stabilization upon startup, directly mitigating dry-start bearing wear and top-end lifter starvation without requiring the purchase of a complete OEM housing assembly.
This product was last offered at the strikethrough price on
05-06-2026
The factory VANOS exhaust hub on the S54 engine is known to develop excessive play where the drive tabs interface with the oil pump disk. Over time, this imprecise fitment causes a back-and-forth rattling motion that can result in the tabs shearing off inside the engine, risking catastrophic damage or complete engine failure. Unlike other aftermarket solutions that require full VANOS disassembly, retiming, or replacement of the oil pump disk, the Turner Motorsport S54 VANOS Hub Upgrade offers a smarter approach. Our bolt-on fix eliminates the common failure point without opening the VANOS unit or disturbing engine timing.
Our solution involves removing the worn tabs from your stock exhaust hub and installing our precision-fit replacement, which is precision-machined from 4340 steel and hardened to meet OEM specifications. Designed using 3D scanning and CAD modeling, the Turner Motorsport VANOS Exhaust Hub Upgrade provides a tight, interference-free fit into the oil pump disc, completely resolving the issue without unnecessary labor.
Features & Benefits:
Direct bolt-on solution for S54 VANOS oil pump drive tab failure, preventing potentially catastrophic damage to engine internals Precision-machined from high-strength 4340 steel and heat-treated to match OEM specifications Designed using 3D scanning and CAD modeling to ensure precise fitment within the OEM oil pump disc Engineered to eliminate the play that exists between the exhaust hub and oil pump disc from factory Backed by extensive real-world testing and our lifetime replacement program!
Over time, the factory valve cover hardware on M50, M50TU, M52, M52TU, M54, S50 (US), and S52 engines is subjected to continuous heat cycling, oil vapor, and moisture, causing original cap nuts to oxidize, corrode, or thread-strip during routine maintenance. Our Polished Valve Cover Cap Nut serves as a direct replacement designed to address these common failure points while improving upon overall engine bay aesthetics.
Because maintaining precise gasket compression is critical to preventing oil leaks, these cap nuts and washers are machined directly to OE-style dimensions. This exact fitment allows for direct compatibility with original and replacement valve cover studs (see T#55317643) and ensures the hardware can be torqued precisely to OEM specifications without guesswork. Manufactured to grade 8.8 structural strength standards, the hardware maintains the necessary clamp force required under normal and high-performance engine operating conditions.
To resist corrosion, both the cap nut and washer undergo an electroless nickel plating process during production. Unlike standard zinc coatings that dull or rust over time, electroless nickel provides a uniform layer of corrosion resistance that withstands long-term chemical exposure and extreme temperature swings while giving the hardware a polished, high-end appearance. Each cap nut assembly includes an OE rubber washer seal, ensuring a tight, leak-free barrier that prevents oil from escaping through the mounting studs.
This product was last offered at the strikethrough price on
05-03-2026
This product was last offered at the strikethrough price on
05-03-2026
On M52/S52-equipped BMWs, the factory crankcase ventilation (CCV) system is a notorious weak link. Between brittle plastic corrugated hoses that crumble from heat soak and an internal cyclone diaphragm prone to tearing, a failing CCV leads to massive oil consumption, vacuum leaks, and that dreaded "howling" whistle.
This kit addresses these issues with all new components and hardware. Both oil separator hoses, the cyclone separator itself, the mounting grommet, and the retaining bolts are included. Servicing this system is guaranteed to restore performance lost as a result of worn CCV components.
Kit includes:
Cyclone Separator/Crankcase Pressure Regulator Valve High Performance Silicone Breather Hose Return Hose Mounting Grommet Hex Bolt (3)
This product was last offered at the strikethrough price on
05-30-2026
This product was last offered at the strikethrough price on
05-30-2026
Take the guesswork out of S54 ownership. This all-inclusive kit targets the two most notorious failure points on the BMW S54 engine: broken exhaust hub tabs and degraded internal seals.
Turner Motorsport S54 VANOS Exhaust Hub Upgrade
The factory S54 exhaust hub is a ticking time bomb. Excessive play between the drive tabs and the oil pump disk creates a rhythmic rattling that eventually shears the tabs off, risking catastrophic engine failure.
While other kits require deep-engine surgery, our Turner Motorsport Hub Upgrade offers a "work smarter" approach.
Precision Engineering: Developed using 3D scanning and CAD modeling for a perfect, interference-free fit.
Superior Materials: Machined from high-strength 4340 steel and hardened to OEM specifications.
No Re-Timing Required: This bolt-on fix eliminates the failure point without the need to disassemble the VANOS unit or disturb engine timing, saving hours of labor.
ECS Tuning VANOS Seal Kit
The original BMW seals are made of Buna-N rubber, which quickly hardens and loses its sealing properties when exposed to synthetic oil and high heat. Our ECS engineering team has corrected this flaw.
Viton™ Upgrade: We utilize high-performance Viton O-rings for the internal seals, seal plate, and solenoid.
Chemical Resistance: These seals are designed to remain pliable and effective for the life of the engine, restoring lost low-end torque and smoothness.
ECS Tuning Rattle Repair Kit
Eliminate the dreaded "marbles in a can" sound. This kit addresses the axial play in the VANOS helical gears.
Hardened Steel: Our rings and washers are precision-ground to resist the wear and deformation that lead to engine rattle.
Silent Operation: Restores the refined sound and feel of your S54 across the entire RPM range.
This product was last offered at the strikethrough price on
05-30-2026
This product was last offered at the strikethrough price on
05-30-2026
The factory VANOS exhaust hub on the S54 engine is known to develop excessive play where the drive tabs interface with the oil pump disk. Over time, this imprecise fitment causes a back-and-forth rattling motion that can result in the tabs shearing off inside the engine, risking catastrophic damage or complete engine failure. Unlike other aftermarket solutions that require full VANOS disassembly, retiming, or replacement of the oil pump disk, the Turner Motorsport S54 VANOS Hub Upgrade offers a smarter approach. Our bolt-on fix eliminates the common failure point without opening the VANOS unit or disturbing engine timing.
Our solution involves removing the worn tabs from your stock exhaust hub and installing our precision-fit replacement, which is precision-machined from 4340 steel and hardened to meet OEM specifications. Designed using 3D scanning and CAD modeling, the Turner Motorsport VANOS Exhaust Hub Upgrade provides a tight, interference-free fit into the oil pump disc, completely resolving the issue without unnecessary labor.
Features & Benefits:
Direct bolt-on solution for S54 VANOS oil pump drive tab failure, preventing potentially catastrophic damage to engine internals Precision-machined from high-strength 4340 steel and heat-treated to match OEM specifications Designed using 3D scanning and CAD modeling to ensure precise fitment within the OEM oil pump disc Engineered to eliminate the play that exists between the exhaust hub and oil pump disc from factory Backed by extensive real-world testing and our lifetime replacement program! Kit Contents:
Turner Motorsport Exhaust VANOS Hub Upgrade 4x Extended Length Hex Head Bolts (M6x30 Gr. 10.9) 8x OEM BMW VANOS Hub Hex Head Bolts (M6x25) 12x Fillister Head Torx Screw (M6x16) OEM Valve Cover Gasket OEM VANOS to Cylinder Head Gasket
This product was last offered at the strikethrough price on
09-01-2026
This product was last offered at the strikethrough price on
09-01-2026
This product was last offered at the strikethrough price on
05-03-2026
This product was last offered at the strikethrough price on
05-03-2026
Schrick has been dedicated to engine performance through the development of only the highest quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track, using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing.
These are a direct replacement for the stock camshafts and offer increased flow at mid and higher RPMs, thanks to 12.5mm of valve lift. Unlike 288/280 camshafts, this 280/272 set does not require upgraded valvetrain parts. The profile of these camshafts is quite close to stock CSL specs.
KIT INCLUDES
Schrick 272-Degree Exhaust Camshaft Schrick 280-Degree Intake Camshaft 24 Turner Motorsport DLC-Coated Performance Rocker Arms NOTE: Camshaft replacement requires multiple special tools. We offer the Genuine BMW Camshaft Press (T#171829) and a Schwaben Camshaft Alignment Tool Set (T#395239) to aid in installation.