BMW Z3 (1996-2002)

BMW E36 Shark Injector Performance Software is the ultimate upgrade for boosting the power and torque of your BMW. This performance software, meticulously dyno-tuned by BMW expert Jim Conforti, is engineered to enhance the potential of high-octane (91+) pump gas, significantly increasing mid-range torque and high-RPM horsepower. The Shark Injector also features an increased rev limit, fine-tuned fuel and spark maps, and optimized performance, ensuring that your BMW exceeds its factory capabilities. The installation is straightforward, typically taking just an hour, and maintains drivability while improving responsiveness.

• Adds +15 HP at 6,400 RPM and +9 lb/ft torque at 4,500 RPM
• Increases rev limit to 7,000 RPM for enhanced engine performance
• Optimized for high-octane fuel, elevating mid-range torque and high-RPM horsepower
• Installation is simple with detailed instructions and takes approximately one hour
• Retains original data for potential future use and eliminates the speed limiter

Note: The Shark Injector software is specifically designed for NORTH AMERICAN SPEC BMWs and is not compatible with EURO-SPEC models.

Stage 2 Performance Software for E36 M3, MZ3 (Turner-Porsche 3.5" HFM, larger injectors)

Conforti Shark Injector performance software tuned for our Stage 2 OBD2 package: larger fuel injectors, Porsche 3.5" HFM, and intake. This is the correct software to use with the desireable Porsche 803/809 HFM on the OBD2 E36 M3. You should not be running a larger HFM without software and injectors - you're in danger of running too lean! On the dyno we found that the stock fuel injectors were not capable of providing enough fuel to keep up with the increased airflow. This "leaner" fuel mixture was dangerous as it could lead to hotter combustion temps and burning or melting of critical components. With the correct HFM, larger injectors, and this software you will be back to running correct air-fuel ratios.

With this software you will notice more top end power, a broader torque band, and a smoother running engine. The rev limit is raised to 7000 RPM with the top speed limiter removed. Works with 91 or higher octane fuel.

Required:
"24lb" injectors (actually around 26lb injectors when used at the S52's 3.5 bar of fuel pressure). You must confirm the injector flow-rate at 3.5 bar before using this software. If the injectors were not purchased from us, we may as for the Bosch part number on your injectors.
Porsche 809 3.5" HFM (0 280 217 809) (TMS/Porsche HFM works best) with intake. Note: this will not work with a Euro HFM, 540 HFM, or Dinan HFM. Our software is programmed and written specifically for the Porsche 809 HFM! If you did not purchase the HFM Kit from us, we may ask you for the Bosch part number from your HFM.
 

Shark Injector Installation Instructions

(click to expand)

Shark Injector installation instructions
A capable battery charger is required for the installation. The charger provides backup power supply to the regular car battery during installation. It must be capable of holding a continuous 10amp charge for the full installation (15-20 minutes).
The minimum octane fuel for this software is 91.

Shark Injector FAQ

(click to expand)

Shark Injector FAQ

This item fits the following BMWs:
1996-1999 E36 BMW M3

Stage 3 Performance Software for E36 M3, MZ3 (HFM/Cam Kit) (stock S52 manifold)

Conforti Shark Injector performance software tuned for our Stage 3 OBD2 package: Schrick camshafts, "24lb" injectors, Porsche 3.5" HFM, and intake. This software is tuned around the stock S52 intake manifold. For keeping the most useable torque we recommend using the stock manifold over the M50 part.

With this software you will notice more top end power, a broader torque band, and a smoother running engine. The rev limit is raised to 7000 RPM with the top speed limiter removed. Works with 91 or higher octane fuel.

Required:
"24lb" injectors (actually around 26lb injectors when used at the S52's 3.5 bar of fuel pressure). You must confirm the injector flow-rate at 3.5 bar before using this software. If the injectors were not purchased from us, we may as for the Bosch part number on your injectors.
Porsche 809 3.5" HFM (0 280 217 809) (TMS/Porsche HFM works best) with intake. Note: this will not work with a Euro HFM, 540 HFM, or Dinan HFM. Our software is programmed and written specifically for the Porsche 809 HFM! If you did not purchase the HFM Kit from us, we may ask you for the Bosch part number from your HFM.
Schrick camshafts
 

Shark Injector Installation Instructions

(click to expand)

Shark Injector installation instructions
A capable battery charger is required for the installation. The charger provides backup power supply to the regular car battery during installation. It must be capable of holding a continuous 10amp charge for the full installation (15-20 minutes).
The minimum octane fuel for this software is 91.

Shark Injector FAQ

(click to expand)

Shark Injector FAQ

This item fits the following BMWs:
1996-1999 E36 BMW M3

You may be able to upgrade the Shark Injector file to another version to better meet your tuning needs. Depending on the model we may have better tunes for things such as intakes, larger air sensors, camshafts, headers, and others. For a small fee the current Shark Injector tune can be removed and a new file added instead (the original Shark file you were using would no longer be available). To do this, we need the car restored to stock settings with the current Shark Injector and then returned to us (updating via USB is not yet available). Sharks that were not Restored to stock cannot be upgraded and the unit will be returned to you (at your expense). We also perform other work on the Shark Injector while it is here, including diagnostic tests and re-packaging with the most current instructions. The Shark that you get back is virtually new and ready to be reinstalled!

To get started, review the catalog of current Shark Injector files for one that better matches your tuning spec.
1. Enter the new tuning file in the form below. Include any other relevant information.
2. Click the Update Price or Add To Cart button.
3. Complete the online transaction with your address and payment information.
4. A Turner Motorsport sales rep will contact you after your order has been submitted. Do not send in your Shark Injector until someone has contacted you with a reference number and return shipping address.

Turn-around time for upgrades is typically the same day we receive it. UPS Ground is the normal return shipping method unless you specify faster shipping on your order. 

Helpful Links:

• Shark Injector File List - listing of all Shark Injector files by vehicle model. Select a file from this list to upgrade to.
• Shipping Instructions - specific instructions for packaging and shipping. Also includes a contact form to include when you send back your Shark.
• Emissions Waiver - some tunes require this emissions/smog waiver before we can program the new file to your Shark. These are noted in the catalog listing in the links above. Print and include this Waiver when you send in your Shark.

Shark Injector installation instructions

Stage 4 Performance Software for E36 M3 (Turner HFM + Cams + Headers Kit)

Conforti Shark Injector performance software tuned for our Stage 4 OBD2 package: Schrick camshafts, performance headers, "24lb" injectors, Porsche 809 3.5" HFM, and intake. This software is tuned around the stock S52 intake manifold. For keeping the most useable torque we recommend using the stock manifold over the M50 part.

With this software you will notice more top end power, a broader torque band, and a smoother running engine. The rev limit is raised to 7000 RPM with the top speed limiter removed. Works with 91 or higher octane fuel.

Required:
"24lb" injectors (actually around 26lb injectors when used at the S52's 3.5 bar of fuel pressure). You must confirm the injector flow-rate at 3.5 bar before using this software. If the injectors were not purchased from us, we may as for the Bosch part number on your injectors.
Porsche 809 3.5" HFM (0 280 217 809) (TMS/Porsche HFM works best) with intake. Note: this will not work with a Euro HFM, 540 HFM, or Dinan HFM. Our software is programmed and written specifically for the Porsche 809 HFM! If you did not purchase the HFM Kit from us, we may ask you for the Bosch part number from your HFM.
Schrick camshafts
Performance Headers (TMS Shorty Headers or similar)
 

Shark Injector Installation Instructions

(click to expand)

Shark Injector installation instructions 
A capable battery charger is required for the installation. The charger provides backup power supply to the regular car battery during installation. It must be capable of holding a continuous 10amp charge for the full installation (15-20 minutes).
The minimum octane fuel for this software is 91.

Shark Injector FAQ

(click to expand)

Shark Injector FAQ

This item fits the following BMWs:
1996-1999 E36 BMW M3