BMW Z3 (1996-2002)

Maintaining proper oil levels in your engine is crucial for peak performance. Undetected leaks can cause your oil to drop to dangerously low levels between oil changes, leading to severe engine damage.

One common culprit for oil leaks is the valve cover. Over time, exposure to extreme temperature fluctuations can wear down the gaskets, causing them to fail. Prevent oil leaks and protect your engine by replacing these vital components.

Comprehensive Kit Includes:

Valve Cover Perimeter Gasket Valve Cover Spark Plug Tube Gaskets 15 Rubber Grommets/Sealing Washers Ultra-Black RTV Gasket Maker Replace your old gaskets with our high-quality kit to keep your engine running smoothly and efficiently.

Proper valve lash adjustment is critical for longevity and performance. If your S54 is due for valve adjustment maintenance you can do it yourself with this kit, saving hundreds of dollars in labor charges. 

Includes

• Shim set 
• Installation tool #83300493743
• 16 Blade Feeler gauge set 

BMW recommends S54 valve inspection and adjustment every 30k miles.

*Click here for valve adjustment instructions*

When your CPV O-ring fails it causes a slow oil leak on the passenger side of the engine, making an oily mess that frequently resembles a rear main seal leak. Replacing the CPV with an upgraded o-ring ensures a long-term solution to this common problem. 

The factory o-ring over time fails from heat cycling and oil exposure due to the Buna rubber used in OEM o-rings, while the included Viton Fluoroelastomer is resistant to a much higher temperature to ensure prolonged life without leaking. 

The fuel pump is held into the tank with a retaining lock ring. Most people would take an extension or punch and tap out the ring with a hammer. But that's the wrong way to do it. You could damage the lock ring, or worse, the tank itself. This handy tool is toothed to match the lock ring and takes a standard 1/2 drive ratchet or small extension. Twist the ratchet and the lock ring comes un-done cleanly and smoothly. A hefty tool that pays for itself over and over. Fits most BMWs from 1988-2013. Also has application for MINI and Porsche.

This metal screw ring tightens down to old the top of the fuel pump or fuel filter assembly dependent on model of vehicle.

Together they make this job simple and easy and ensure a tight fit with a new ring. 

The ZF 320z S5D is a common swap choice among BMW enthusiasts due to its reliable and robust nature. Unfortunately, it does have a weakness. The detent pins and springs that live inside of the transmission are known to wear down over time, often causing the shift lever to lean towards the 5th gear position when in neutral.

This full-service kit consists of everything you need to replace the failing detents in your ZF transmission. The kit contains only Genuine ZF components, all of which are sure to provide you with smooth shifting and operation for years to come.

This kit includes the following items:

3 Shift Pin Kits - 23117525048
2 Slide Bushings - 23117533395
2 Gearbox sealing lids - 23311224825
1 Shifter detent pin - 23311224849
1 Shifter detent pin - 23317502165
2 Lock Rings - 23317531374
3 Spring Retention Plates - 23317637524
5 Detent Drift/Punch Tools - 054834LA01AKT
Remedying the ZF's detent issue is a must for any enthusiast planning to get the most out of their transmission. Proper centering is essential for quick and smooth shifting, both being desirable features in any application. This kit is easy to install with several DIY guides existing online. A set of "drift" tools are included for proper installation.

When replacing your worn out brakes, the market is flooded with performance options. If your BMW doesn't see track time, it's not very practical. Performance pads and rotors tend to result in a lack of bite at low braking temperatures and cause excessive noise in daily driven vehicles that becomes irritating. BMW brakes from the factory are perfectly suited for trips around town, across the country, and even the occasional spirited driving session, delivering smooth, quiet, and long lasting performance. 

Included in this E36 BMW brake package are all of the OEM equivalent components needed to replace your Front & Rear brakes with comfort, reliability, and optimal lifespan in mind.

Brake components in this kit:

• Pagid Front & Rear Brake Pads
• Pagid Front & Rear Rotors
• New Front & Rear Wear Sensors
• Brand New Stainless Steel Set Screws
• Syl-Glide Silicone Brake Lubricant 

Fits the following BMWs:
E36 BMW M3 S52/S50
Z3 BMW M Coupe/Roadster S52/S54

This kit is contains all new strut and shock mounts and hardware needed when installing a new shocks and struts or aftermarket suspension on your vehicle. 

Fits the following BMW's

E36 318i/ic/is 323i/ic/is 325i/is/ic 328i/is/ic 

• Disable EWS coding in ECU
• Unlock torque and horsepower
• Smoother engine with less hesitation
• Improved throttle response
• Rev limit increased to 7000
• Top speed limiter removed
• Installs in minutes!

Performance software is a  must-have  upgrade on your BMW and you won't find an easier and better software solution than the Shark Injector. Developed by BMW tuning expert Jim Conforti, this device plugs into the car's diagnostic port and flashes new performance files into your car's engine computer (ECU). This particular file includes Stage 1 engine tuning (fuel, ignition, timing upgrades) with EWS-delete programming. There's no removal of the ECU and shipping, no cables, no laptop required - only a battery charger! Installation takes just a few minutes and your engine will perform like never before!

The M52/S52 performance software was developed on the dyno to create maximum power and torque using premium 91+ octane fuel while maintaining BMW reliability and smoothness. The software makes changes to the ECU's maps and algorithms for fuel injection, ignition timing, VANOS and camshaft movement, and transitional fueling. We modify the maps for part throttle and full throttle so you get better response and more torque at all RPM. We also raise the rev limit to 7,000 and remove the top speed limiter. By fine tuning these maps we've been able to improve the S52 engine beyond what BMW did by making more power and torque and a smoother-running engine.

The programming for EWS delete will allow you to use a spare ECU to run the engine. If your original ECU fails, and you find yourself buying a used ECU, you won't have to tow the car to the dealer to have the ECU synced to the car's EWS system. This is also the perfect software solution if you installed an S52 engine in your E36 323/328 - just plug in the M3 ECU and flash with this Shark Injector. This Stage 1 file will bypass the EWS code and give you all of the benefits of our Stage 1 tune.

The Shark Injector plugs into the diagnostic port under the hood of the E36. With the battery charger supplying power, press the Upgrade button and within minutes the ECU is reflashed with the new performance tune. No other software product on the market comes close to how easy it is to install. You can use the Restore button to re-install the stock BMW software at any time. Detailed instructions are included. Other tuners require you to remove the ECU and ship it to them or use a laptop to read and write a new file. The Shark Injector is ready to install right out of the box! A planned future upgrade will allow you to use the USB port to load different performance files.

1996-1999 E36 M3 Performance Software Peak Gains

E36 M3 dyno chartHP Gain Up To:+12 @ 6,000 RPM

Torque Gain Up To:+10 @ 4,000 RPM

New Rev Limit:7,000 RPM

Read what others are saying!

(click to expand)

Manny, E36 M3: "Just "sharked" my E36 M3. All I can say is WOW. The car has never run so well. The idle and the engine overall is so smoooooth! The throttle is very responsive, power is right there. Very Nice! Never putting it back to stock! Just wanted to say job well done, and thanks."

Josh, E36 M3: "Just got done putting on my Supersprint exhaust, Shark injector and my intake, wow what a difference. Thank you guys for the performance, I will be a lifetime customer."
 

Shark Injector Installation Instructions

(click to expand)

Shark Injector installation instructions
A capable battery charger is required for the installation. The charger provides backup power supply to the regular car battery during installation. It must be capable of holding a continuous 10amp charge for the full installation (15-20 minutes).
The minimum octane fuel for this software is 91.

Shark Injector FAQ

(click to expand)

Shark Injector FAQ

This item fits the following BMWs:
1996-1999 E36 BMW M3
1998-2000 Z3 BMWZ3 M Roadster M Coupe

Stage 2 Performance Software for E36 M3, MZ3 (Turner-Porsche 3.5" HFM, larger injectors)

Conforti Shark Injector performance software tuned for our Stage 2 OBD2 package: larger fuel injectors, Porsche 3.5" HFM, and intake. This is the correct software to use with the desireable Porsche 803/809 HFM on the OBD2 E36 M3. You should not be running a larger HFM without software and injectors - you're in danger of running too lean! On the dyno we found that the stock fuel injectors were not capable of providing enough fuel to keep up with the increased airflow. This "leaner" fuel mixture was dangerous as it could lead to hotter combustion temps and burning or melting of critical components. With the correct HFM, larger injectors, and this software you will be back to running correct air-fuel ratios.

With this software you will notice more top end power, a broader torque band, and a smoother running engine. The rev limit is raised to 7000 RPM with the top speed limiter removed. Works with 91 or higher octane fuel.

Required:
"24lb" injectors (actually around 26lb injectors when used at the S52's 3.5 bar of fuel pressure). You must confirm the injector flow-rate at 3.5 bar before using this software. If the injectors were not purchased from us, we may as for the Bosch part number on your injectors.
Porsche 809 3.5" HFM (0 280 217 809) (TMS/Porsche HFM works best) with intake. Note: this will not work with a Euro HFM, 540 HFM, or Dinan HFM. Our software is programmed and written specifically for the Porsche 809 HFM! If you did not purchase the HFM Kit from us, we may ask you for the Bosch part number from your HFM.
 

Shark Injector Installation Instructions

(click to expand)

Shark Injector installation instructions
A capable battery charger is required for the installation. The charger provides backup power supply to the regular car battery during installation. It must be capable of holding a continuous 10amp charge for the full installation (15-20 minutes).
The minimum octane fuel for this software is 91.

Shark Injector FAQ

(click to expand)

Shark Injector FAQ

This item fits the following BMWs:
1996-1999 E36 BMW M3

Stage 3+ Performance Software for E36 M3 (M50 Manifold + Cam Kit)

Conforti Shark Injector performance software tuned for the an awesome OBD2 package: M50 manifold, Schrick camshafts, "24lb" injectors, Porsche 3.5" HFM, and intake. This software makes full use of the benefits of the M50 manifold when used with cams and the HFM/intake. Without the software, you're not getting the full effect of these upgrades in the upper rev range. The stock software -- or a regular Shark Injector -- is tuned for low-end torque using the stock manifold and cams. It's like a marathon runner in a 40-yard dash -- he'll put in a good effort but won't be the quickest! Special attention was paid to the low-end and mid-range too so that torque was not lost with the M50 manifold.

With this software you will notice more top end power, a broader torque band, and a smoother running engine. The rev limit is raised to 7000 RPM with the top speed limiter removed. Works with 91 or higher octane fuel.

Required:
"24lb" injectors (actually around 26lb injectors when used at the S52's 3.5 bar of fuel pressure). You must confirm the injector flow-rate at 3.5 bar before using this software. If the injectors were not purchased from us, we may as for the Bosch part number on your injectors.
Porsche 809 3.5" HFM (0 280 217 809) (TMS/Porsche HFM works best) with intake. Note: this will not work with a Euro HFM, 540 HFM, or Dinan HFM. Our software is programmed and written specifically for the Porsche 809 HFM! If you did not purchase the HFM Kit from us, we may ask you for the Bosch part number from your HFM.
Schrick camshafts
M50 intake manifold
 

Shark Injector Installation Instructions

(click to expand)

Shark Injector installation instructions
A capable battery charger is required for the installation. The charger provides backup power supply to the regular car battery during installation. It must be capable of holding a continuous 10amp charge for the full installation (15-20 minutes).
The minimum octane fuel for this software is 91.

Shark Injector FAQ

(click to expand)

Shark Injector FAQ

This item fits the following BMWs:
1996-1999 E36 BMW M3