Please ensure your correct model is selected
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
If your M50, M52, or M54 engine takes a few seconds to build oil pressure after sitting, there's a good chance that your factory oil filter housing drain back valve has failed. Over time, the factory plastic check valve degrades, allowing oil to drain completely out of the housing and back into the oil pan while sitting. Every cold start essentially becomes a dry start, resulting in a loud ticking noise and causing unnecessary wear on your engine's internals.
Unfortunately, BMW does not offer this check valve as a standalone part, forcing you to purchase a costly, complete oil filter housing assembly just to fix one failed plastic component. Thankfully, our team of BMW enthusiasts took note of this common failure mode and designed a permanent, cost-effective fix.
Our Billet Oil Filter Housing Drain-Back Valve is designed as a direct-fit upgrade for your factory oil filter housing. CNC-machined from high-strength billet aluminum, this upgraded valve restores positive sealing to keep the oil filter housing fully primed. Maintaining this hydraulic prime ensures rapid oil pressure stabilization upon startup, directly mitigating dry-start bearing wear and top-end lifter starvation without requiring the purchase of a complete OEM housing assembly.
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
Through experimentation and data acquired from our E36 World Challenge Touring Cars, it was discovered that in long corners and under heavy braking that there was an oil starvation problem in the M50 and M52 engines. This system was developed to keep oil in the sump and eliminate the starvation problem. After several iterations, further testing and data acquisition in the Touring Cars showed that this system eliminates the problem of oil starvation. This is a less expensive alternative to replacing the stock oil pan with the factory BMW M3 Lightweight oil pan, while still achieving the similar results.
*Requires Professional Welding
Installation instructions (E36/Z3 Oil Pan Baffle for M50, M52, S50, S52 engines)
This item fits the following BMWs:
1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1992-1995 E34 BMW 525i
1997-1998 E39 BMW 528i
1997-1998 Z3 BMW Z3 2.8
1998-2000 Z3 BMW Z3 M Coupe M Roadster S52
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
Through experimentation and data acquired from our E36 World Challenge Touring Cars, it was discovered that in long corners and under heavy braking that there was an oil starvation problem in the M50 and M52 engines. This system was developed to keep oil in the sump and eliminate the starvation problem. After several iterations, further testing and data acquisition in the Touring Cars showed that this system eliminates the problem of oil starvation. This is a less expensive alternative to replacing the stock oil pan with the factory BMW M3 Lightweight oil pan, while still achieving the similar results.
*Requires Professional Welding
Installation instructions (E36/Z3 Oil Pan Baffle for M50, M52, S50, S52 engines)
This item fits the following BMWs:
1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1992-1995 E34 BMW 525i
1997-1998 E39 BMW 528i
1997-1998 Z3 BMW Z3 2.8
1998-2000 Z3 BMW Z3 M Coupe M Roadster S52
Upgrade your BMW's oil pressure sensor setup with the Oil Distribution/Sending Block. This versatile block is designed to mount in the stock oil pressure sensor location on the oil filter housing or in the original location on the engine block. It allows the use of up to two aftermarket sending units (not included) along with the factory sensor, providing accurate pressure and temperature measurements. Engineered for reliability and cleanliness, it ensures a reliable setup for your BMW's oil pressure monitoring needs.
Rally Road Productions, Inc. is a team supported by a group of people with great abilities in their area of expertise. From the "web guy" and driving instructor friends, to owners of various machine shops, they have surrounded ourselves with people that can be trusted to create and manufacture quality products. This is the key to ensuring everything that they sell will perform as it was intended. The goal is to increase customer satisfaction and make the customization or performance enhancement of your vehicle a more enjoyable venture.
This oil cooler system is race tested and proven to outflow the euro M3 oil filter housing. Additionally, this particular system uses a sealing mechanism to direct the oil flow through the cooler lines and then through the oil filter. Other cooler caps do not provide this seal and therefore the external oil coolers and lines act as a "balloon". The lines and cooler are pressurized, but oil does not flow through them. Flowing oil means it is being cooled and not just acting as an external reservoir.
Flow testing reveals that the oil cooler cap will outflow the Euro M3 Oil Filter Housing by more than 80% at the same, pressure, RPM, and oil temperature. In the upper RPM range, there is nearly a 100% improvement in flow from the RallyRoad oil cooler cap when compared to the Euro M3 oil filter housing. This is a massive improvement over OE and is a worthwhile upgrade, especially in engines that see severe duty.
Features:
Kit Includes:
This part fits the following BMWs
1992-1999 E36 323i 325i 325is 328i 328is
