BMW Suspension Parts for BMW Z3 (1996-2002)

This strut and shock mount package covers the front and rear rubber mounts and bushings commonly replaced during a strut and shock install. While you're installing new front struts and rear shocks these are easily installed - there's no additional labor and special tools are not required. Since these pieces are mostly rubber, they dry up and crack over time. Re-using them lead to problems with fitment or noise, and may have safety issues as well. These mounts and pads are the perfect complement to your new shocks to help restore your car's handling and performance.

We sell the basic strut and shock mount package, which includes:

• Front strut mounts (also known as guide support)
• Front strut reinforcement plates (to prevent cracking and deforming of the front strut towers)
• Front strut tower paper washer gaskets
• Front and rear self-locking mounting nuts
• Rear Lifetime Warranty 'Repair Shop' shock mounts
• Rear shock mount reinforcements (to prevent cracking of shock towers)
• Rear shock mount gaskets

In addition, you can add the front spring pads, front bump stops, front dust boots, rear bump stops, and rear dust boots if needed. But please note that some shocks and coil overs come with all or some of these pieces already. If in doubt, check with your supplier on what is included.

We offer three varieties of the rear shock mounts - OEM, Repair Shop, and HP alum-rubber. We recommend either the Repair Shop or HP mounts because the stock OEM design has a flaw that can lead to premature failure of the mounts. The Repair Shop and HP mounts use a different design that will last longer and the Repair Shop mounts also have a lifetime warranty!

This item fits the following BMWs:
1996-1999 E36 BMW M3
1996-2002 Z3 BMW 2.5 2.5i 2.8 3.0i M Coupe

Want the best performance option in shock tower mounts? IRP has created their pillow-ball rear shock mounts for just this need. These rear shock mounts are designed for use on the track and racing. This set of mounts will help your rear shocks perform the best they can in all conditions. The advantage to using a mount with spherical bearing is that it allows the shock to freely move off axis without side loading the shock shaft like rubber or polyurethane mounts do. Side loading a shock increases stiction and wear which decreases its efficiency. Because these are mounts without an isolator (rubber or polyurethane) to dampen road noise and vibrations we do not recommend them for street cars.

The bearing sleeve and poly bushing are built to work with all stock style shocks such as Bilstein and H&R coilover and suspension kits.

Fits the following BMW chassis:
E36 BMW All Submodels except for 318ti
E46 BMW All Submodels
E30 BMW All Submodels
E36 Z3 BMW All Submodels
E85/E86 Z4 BMW All Submodels

Bushings tends to wear over time and split or even break free from the internal sleeve, causing excessive movement and sloppy control feel. OEM Lemförder bushings are the perfect option to restore suspension back to day 1 quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Bushings tends to wear over time and split or even break free from the internal sleeve, causing excessive movement and sloppy control feel. OEM Lemförder bushings are the perfect option to restore suspension back to day 1 quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

One common weak point in the E36 3-series model range is in the mounting and ball joints of the suspension. The front suspension ball joints in particular are prone to wearing out quite quickly thanks to a soft material in the ball joint itself, leaving you in a potentially dangerous situation. At best, worn ball joints and bushings will give you poor steering feedback and clunking noises. However, loose or worn ball joints will have excessive play which will drastically reduce the effectiveness of the steering and suspension. In extreme cases, the ball joint has been known to pop free of the control arm, resulting in total steering loss.

Meyle has addressed this problem with a higher-grade metal in their HD ball joints, similar to those used on the E36 M3. The metal will not wear or fatigue nearly as fast as the standard ball joints. The lifespan is greatly extended. A side benefit of the stiffer joint is better steering response. The metal will not flex or deflect like plastic, rubber, or any other material. The lack of play will mean sharper steering, restoring much of the car's precision and fun-to-drive character. Meyle is a German brand in business since 1958 and all of their products are TUV approved and meet or exceed ISO standards.

We supply the Meyle HD control arms as a set with new M3 rubber control arm bushings. You can choose bushings with either a centered hole (same as stock original) or with an offset hole (adds caster and camber). The stock rubber bushings (manufactured by Boge) will be perfect for most people but if you're looking for an upgrade, the offset bushings will give the car quicker steering response. The solid rubber mounts last longer and give better feedback than the original web design.

All Meyle HD parts come with a 4-year, unlimited mileage warranty.

Features:

• 4 Year Warranty

• All metal ball joints are more reliable and longer lasting than stock

• Bushings are solid rubber rather than fluid filled, providing longevity and handling feel improvements

Package Options:
Bushings without control arm brackets.
Bushings pre-installed into new control arm brackets

Applications:
1992-1999 E36 318i, 318is, 323i, 323is, 325i, 325is, 328i, 328is, including all sedan, coupe, and convertible models.
1995-1999 E36 318ti Compact and hatchback models
1996-2001 Z3 1.9, 2.3, 2.5, 2.8, 3.0

Rear shock mounts are tasked with securing shocks while absorbing noise, vibration and harshness that would otherwise be associated with a solid mount. Factory rubber bushings are a compromise between a cushy ride and responsive handling.

Powerflex polyurethane rear shock mounts are firmer than OEM bushings, resulting in better handling, a more responsive rear-end, and more efficient suspension articulation - all with minimal sacrifice to ride quality.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 2 kit replaces:

Subframe Bushings
Shock Mounts & Reinforcement Plates
Polyurethane Diff Bushing
Rear Trailing Arm Bushings
Sway Bar End Links
Hardware

OE gasket ring for the BMW rear suspension mount.

Genuine BMW Washer-Gasket
This item fits the following BMW Chassis:
E30 M3,E36 M3,E46 M3,E85 Z4M,E30,E36,E46,E85 Z4,E86 Z4
 

If your differential is leaking fluid, this is the likely cause. Restore the tight seal with this Genuine BMW seal to prevent potential damage or future failure.

Fits the following BMW Chassis:
E30, E36, E28, E34, E24, E23, E32, E38, Z3