If you're not sure if your Vanos seals are bad then the only question you need to answer is if you've replaced them. Every unit from the factory came with the same failure prone o-rings and seals, even the re-manufactured units you can still get today. The only real fix is by replacing the seals and o-rings with material that is built to last in the oiled, extreme temperature environment found in these kits. 

A premium product replacement with easy to follow instructions makes rebuilding your Vanos unit a must. Even thought the power loss is barely felt it's the opposite result once you replace the seals, every car that gets rebuilt ends up wowing the customer and all of them saying they didn't realize what they lost. 

There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.

While you 're replacing the seals in your Vanos unit it a good time to install anti-rattle spacers to tighten up the gaps in your stock assembly and get rid of that noisy Vanos clatter.

Rebuild instructions : http://bd8ba3c866c8cbc330ab-7b26c6f3e01bf511d4da3315c66902d6.r6.cf1.rackcdn.com/PDF_12017_BMW_M5X_Dual_Vanos_Rebuild_Kits.pdf

This item fits the following BMWs: 

1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi 
1999-2003 E39 BMW 525i 528i 530i 
2004-2010 E60 BMW 525i 530i 
2004-2006 E83 BMW X3 2.5i X3 3.0i 
2000-2006 E53 BMW X5 3.0i 
1999-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i 
2003-2005 Z4 BMW Z4 2.5i Z4 3.0i 

Enhance Your BMW's Braking Performance with ECS Tuning's Innovative Package

Upgrade the braking capabilities of your BMW E36 M3 or Z3M with ECS Tuning's advanced braking package. This solution prioritizes increased brake torque and thermal capacity, utilizing ECS 2-piece E46 M3 CSL rotors to deliver outstanding performance behind 18" wheels and compatible 17" big brake-friendly wheels.

Key Benefits:

• Custom-designed caliper bracket for fitting ECS 2-piece E46 M3 CSL rotors
• Lightweight aluminum hats for reduced weight and enhanced durability
• Gray cast iron rings for wear resistance and efficient heat dissipation
• 2-Piece semi-floating construction prevents rotor warping
• Heat-treated for increased strength and performance
• Directionally veined for accelerated cooling
• Drilled and slotted design for improved ventilation and cleaner brake pads
• Overall weight savings for improved braking and suspension performance
• High manufacturing quality for corrosion resistance and long-term durability

Installation is hassle-free, utilizing existing calipers, pads, lines, and hardware. Upgrade your pads simultaneously with a wide selection of E36 M3 or E46 M3 brake pads for enhanced performance.

These 2-piece floating rotors help dissipate heat better than a standard cast iron rotor and are also lighter for less unsprung weight. Managing heat in the brake system is vital to braking performance, especially on the track or when driven hard. It's why your brake rotors have internal vanes that vent heat as the rotor spins. These 2-piece ECS rotors feature an outer cast iron friction surface ring that is separate from the aluminum center hat. This allows better airflow through the vanes and for the friction ring can expand as it gets hot. The rotors are also cross-drilled for better ventilation and slotted to improve brake pad performance.

ECS 2-Piece Rotors feature:

• Aluminum hats for light weight
• Heat-treated cast iron friction rings
• 2-piece assembly improves brake cooling
• Anti-corrosion coating on non-friction surfaces and hard anodizing on rotor hat

These are the same size as the stock rotors so your stock caliper and mounting bracket will fit and there will be no clearance issues with your wheels or to other components. Stainless steel rotor retaining screws are included. You can use these with any brake pad.

Price is for the pair of brake rotors.

This item fits the following BMWs:
1999-2006 E46 BMW 323i Touring Wagon
1999-2006 E46 BMW 323ci Convertible
1999-2006 E46 BMW 325i 325ci 325xi 328i 328ci
2001-2002 Z3 BMW Z3 3.0i
2002-2008 E85 E86 BMW Z4 3.0 M54 Z4 3.0i N52

ECS Tuning 304 Stainless Steel Hose Clamps

Once again, ECS Tuning has found a way to make life easier for working on your car. Need new hose clamps but don't want to wait to order it from the dealership or pay more than you should for a hose clamp? That's where we come in! These are full 304 stainless steel hose clamps with various band widths for your convenience. They are German style using T-bolts to adjust in size to your required diameter. Never pay dealer pricing again, but still get the quality you love here at ECS Tuning.

• Made from high-quality 304 stainless steel for durability
• German-style design with T-bolts allows for easy size adjustment
• Various band widths for versatile use
• Avoid dealership pricing without compromising on quality
• Perfect for BMW enthusiasts seeking affordable yet reliable hose clamps

ECS Tuning Extended Wheel Bolts for Precise Fitment

Enhance your vehicle's wheel fitment precision with ECS Tuning's extended wheel bolts, designed individually or paired with spacers to ensure accurate compatibility. These bolts are engineered to meet the rigorous ISO 898 class 10.9 standards, ensuring exceptional mechanical and physical properties, including stringent material, hardening, tempering, and proof load strength criteria. Our fasteners undergo lab testing to guarantee compliance with class 10.9 requirements.

Bolt Specifications:

• Diameter: 12mm
• Thread Pitch: 1.5mm
• Length: 45mm

*For proper fitment when using wheel spacers, add the spacer size to the length of the OE wheel bolt (e.g., 27mm Length OE Wheel Bolt + 15mm Wheel Spacer = Requires a 42mm Length Bolt)

Upgrade your hose fittings with the Adjustable Hose Clamp. Designed for versatility and reliability, this clamp provides a secure and adjustable solution for various hose sizes. With its durable construction and easy-to-use design, it ensures leak-free connections in automotive, plumbing, and industrial applications. Say goodbye to loose hoses and enjoy peace of mind with this essential hose clamp.

• Provides secure and adjustable solution
• Durable construction for reliability
• Easy-to-use design for convenience
• Suitable for automotive, plumbing, and industrial applications

12x1.5 Conical Seat Wheel Nuts with 17mm Hex Head

ECS Tuning introduces 12x1.5 conical seat wheel nuts featuring a 17mm hex head, tailored for vehicles that have transitioned to a stud-style mounting system. These open-ended wheel nuts are the perfect solution for accommodating longer studs without any fitment concerns.

Product Details:

• Thread Size: 12x1.5
• Hex Head Size: 17mm
• Designed for vehicles with stud-style mounting
• Open-ended design to accommodate longer studs

The caliper sliding bolts are one of the most overlooked wear items in your braking system. Subjected to constant motion and often without adequate lubrication the guide bolts see a lot of wear and tear. Factory BMW caliper guide bolts are very expensive from the dealer - these 304 stainless steel bolts are less than half the price and provide outstanding resistance to corrosion and wear. They are manufacturered with tighter tolerances than the factory bolts too.

Price is per bolt unless noted (2 required per caliper).

Enter your vehicle info for specific fitment information.

ECS Tuning offers high-quality extended wheel bolts, available individually or with matching spacers for precise fitment. These bolts comply with ISO 898 class 10.9 standards, meeting strict material properties and strength requirements. Lab-tested to ensure they meet these stringent specifications.

• Bolt Specifications:
• Diameter: 12mm
• Thread Pitch: 1.5mm
• Length: 43mm

Note: When using wheel spacers, add the spacer size to the OE wheel bolt length for accurate fitment (e.g., 27mm OE Wheel Bolt + 15mm Wheel Spacer = Requires a 42mm Length Bolt)

ECS Tuning is proud to offer extended wheel bolts individually or with our spacers that are matched to take the guesswork out of correct fitment. Our bolts are designed to meet ISO 898 class 10.9 mechanical and physical properties. This is a very strict standard that specifies material properties, hardening and tempering requirements, and proof load strength requirements. Furthermore, our fasteners have been lab tested to verify that they meet class 10.9 requirements.

Bolt specifications:

• Diameter - 12mm
• Thread Pitch - 1.5mm
• Length - 50mm

*When installing wheel spacers, add the size of the spacer to the length of the OE wheel bolt for proper fitment (ex. 27mm Length OE Wheel Bolt + 15mm Wheel Spacer = Require a 42mm Length Bolt)

Transform Your BMW's Exhaust System with ECS UNIVERSAL Exhaust Tips - 4.0" Titanium - Burnt Finish - Set of Four

• Elevates the appearance of your BMW's exhaust system
• Crafted from durable titanium for long-lasting performance
• Features a stylish burnt finish for a unique look
• Comes in a set of four for a complete upgrade

Upgrade the look of your BMW's exhaust system with the ECS UNIVERSAL Exhaust Tips - 4.0" Titanium - Burnt Finish - Set of Four. Made from high-quality titanium, these exhaust tips are built to last and provide a touch of elegance to your vehicle. The burnt finish adds a distinct visual appeal, making your BMW stand out from the crowd. With four tips included in the set, you can achieve a comprehensive upgrade for your exhaust system.

Brake pad wear sensors are a convenient part of the braking system, notifying the driver of when the material on the brake pads are getting low and need to be serviced. Unfortunately it is common in custom or upgraded braking systems that the pad wear sensor is non-existent or does not mate properly with the connector on your vehicle, leaving you with a brake pad wear warning every time you start your vehicle.

ECS Tuning has developed this direct-fit Brake Pad Wear Sensor Bypass to alleviate this issue. This sensor bypass will trick the vehicle's electronics into thinking that the brake pads have adequate pad material to keep the dashboard warning from appearing. No more unnecessary warnings when installing a big brake kit or your own custom setup. This bypass is a plug-and-play component that requires no modifications so you can revert back to your OEM setup if necessary.

Some vehicles may be equipped with two front brake pad wear sensors, or a front and rear sensor, please be sure to double check the required quantity for your vehicle before placing an order.

*During installation, make sure to clean the mated female connector on your vehicle of any dirt or debris to ensure that the Brake Pad Wear Sensor Bypass is engaged securely.

Includes connector housing with terminals and seals. Commonly used for the camshaft position sensor.

ECS Tuning replacement harness connectors include all necessary pins and wire seals for a complete harness repair. Whether you have a broken harness connector or need a complete wiring repair, we have the components you need.

Each connector includes an additional terminal in case one becomes lost or damaged during installation.

*OEM cross reference PN# 12521732596 - Commonly used for the camshaft position sensor.

Please reference the original part number from the existing connector to confirm fitment, before ordering.

Suggested tools:

Suggested crimping pliers: T#387193
Wire De-pin tools:
12pc De-Pin Tool Set - T#386379
23pc De-Pin Tool Set - T#641943

Includes connector housing with terminals and seals. Commonly used for the idle air control valve (IACV).

ECS Tuning replacement harness connectors include all necessary pins and wire seals for a complete harness repair. Whether you have a broken harness connector or need a complete wiring repair, we have the components you need.

Each connector includes an additional terminal in case one becomes lost or damaged during installation.

*OEM cross reference PN# 12521706096 - Commonly used for the idle air control valve (IACV).

Please reference the original part number from the existing connector to confirm fitment, before ordering.

Suggested tools:

Suggested crimping pliers: T#387193
Wire De-pin tools:
12pc De-Pin Tool Set - T#386379
23pc De-Pin Tool Set - T#641943

Achieving precise exhaust fitment can be tricky—especially when the exhaust hanger has room to slide. This movement can cause annoying rattles or even lead to contact with the underbody or rear bumper. The ECS Tuning Exhaust Locking Collar offers a simple and effective fix. Designed to clamp securely around the exhaust hanger, this collar keeps everything firmly in place, eliminating unwanted movement.

Crafted from high-strength 6031 billet aluminum and finished in a sleek black anodized coating, it delivers both durability and corrosion resistance. With this collar in place, your exhaust stays exactly where it should—no rattles, no surprises.

Product Design:

Made from precision machined 6061 aluminum Black anodized finish Stainless steel M5 X 0.8mm hardware Installation & Support:

Install the locking collar around your exhaust hanger, position the hanger in place, and snug the locking collar down in place against the hanger! ECS Exhaust Hanger Locking Collars are available for 10mm and 12mm exhaust hangers. Please measure your hangers before ordering. The 10mm locking collar can be found HERE.

Upgrade your BMW with ECS Tuning's Stainless Steel Hose Clamps, designed for convenience and durability. With various band widths and German-style T-bolts, these clamps offer easy adjustment to your required diameter. Say goodbye to dealer pricing and enjoy the quality you love at ECS Tuning.

• Full stainless steel construction
• Various band widths available
• German-style T-bolts for easy adjustment
• Convenient solution for hose clamp replacement

Upgrade your exhaust system with the Stainless Steel Oxygen Sensor (O2) Weld Bung (M18x1.5mm). This high-quality weld bung is made from stainless steel, ensuring durability and resistance to corrosion. It features M18x1.5mm threads, making it compatible with most oxygen sensors. Perfect for custom exhaust setups or replacing damaged bungs, this weld bung is a must-have for any automotive enthusiast.

• Made from high-quality stainless steel for durability and corrosion resistance
• M18x1.5mm threads ensure compatibility with most oxygen sensors
• Ideal for custom exhaust setups or replacing damaged bungs
• Essential for automotive enthusiasts looking to upgrade their exhaust system

Revamp Your Suspension with the BMW & MINI Coilover Wrench Set

• Compatible with BMW and MINI models for versatile use
• Durable construction ensures long-lasting performance
• Ergonomic design provides comfortable handling during installation
• Allows for precise adjustment of coilovers for optimal ride quality

Upgrade your BMW or MINI's suspension system with the BMW & MINI Coilover Wrench Set. This set is compatible with various BMW and MINI models, offering versatile compatibility for a wide range of vehicles. Constructed from durable materials, these wrenches are built to withstand the rigors of frequent use and provide long-lasting performance. The ergonomic design ensures comfortable handling during installation, reducing fatigue and allowing for more efficient work. With the BMW & MINI Coilover Wrench Set, you can easily adjust your coilovers to achieve the optimal ride quality for your vehicle.

Ensure optimal engine performance with the BMW S54 3.2L O-Ring.

Specifically designed for BMW engines, this o-ring provides a reliable seal to prevent leaks and maintain engine integrity. Crafted with high-quality materials, it withstands high temperatures and pressures, ensuring long-lasting durability. With easy installation and precise fitment, this o-ring is essential for any BMW owner looking to maintain their engine's performance and reliability.

• Provides a reliable seal to prevent leaks
• Withstands high temperatures and pressures
• Ensures long-lasting durability
• Easy installation for convenience
• Precise fitment for BMW engines

Includes connector housing with terminals and seals. Commonly used for the engine oil pressure switch.

ECS Tuning replacement harness connectors include all necessary pins and wire seals for a complete harness repair. Whether you have a broken harness connector or need a complete wiring repair, we have the components you need.

Each connector includes an additional terminal in case one becomes lost or damaged during installation.

Suggested tools:

Suggested crimping pliers: T#387193
Wire De-pin tools:
12pc De-Pin Tool Set - T#386379
23pc De-Pin Tool Set - T#641943

1/2"/12mm Band Hose Clamp

For reliable hose fastening, opt for the top-tier 1/2"/12mm Band Hose Clamp. Engineered for durability and versatility, this hose clamp ensures secure connections in various applications. Invest in quality and maintain optimal functionality with this essential accessory.

• Versatile clamp suitable for various hose sizes
• Durable construction ensures long-lasting performance
• Provides a secure seal for optimal functionality
• Easy to install and adjust for convenience

Includes connector housing with terminals and seals. Commonly used for the crankshaft position sensor.

ECS Tuning replacement harness connectors include all necessary pins and wire seals for a complete harness repair. Whether you have a broken harness connector or need a complete wiring repair, we have the components you need.

Each connector includes an additional terminal in case one becomes lost or damaged during installation.

*OEM cross reference PN# 12521433916 - Commonly used for the crankshaft position sensor.

Please reference the original part number from the existing connector to confirm fitment, before ordering.

Suggested tools:

Suggested crimping pliers: T#387193
Wire De-pin tools:
12pc De-Pin Tool Set - T#386379
23pc De-Pin Tool Set - T#641943

Ensure secure hose connections with the 1/2"/12mm Band Hose Clamp. This versatile clamp provides a tight and reliable seal for various hose sizes, making it ideal for automotive, plumbing, and industrial applications. With its durable construction and easy installation, the 1/2"/12mm Band Hose Clamp is a practical solution for preventing leaks and maintaining efficiency.

• Provides a tight and reliable seal
• Versatile clamp for various hose sizes
• Suitable for automotive, plumbing, and industrial applications
• Durable construction ensures long-lasting use

Is your BMW hood emblem showing signs of wear and tear?

If it's cracked or faded, it's time for a replacement. Introducing the Roundel removal tool, designed specifically for effortless removal of your old emblem and installation of the new one. Made with durable nylon, this tool is both thin enough to fit under the roundel and strong enough to avoid breakage. Say goodbye to your old emblem with ease and give your BMW a fresh, shiny upgrade.

Benefits:

• Effortlessly removes old hood emblems
• Facilitates easy installation of new emblems
• Durable nylon construction ensures longevity
• Compatible with various BMW models