*MADE TO ORDER; ALLOW 2-3 BUSINESS DAYS*
The E9X M3 / E82 1M have unquestionably become modern-day icons for their formidable street and track dominance. Both of these cars are equipped with M12x1.5 hardware from the factory, leaving them precariously prone to failure during rigorous track sessions and consequently, a potentially dangerous and damaging fate.
Fall-Line Motorsport has developed a hub retrofit kit that will convert your E9X M3 / E82 1M to the more robust M14x1.25 hardware as well as shave rotational mass from each corner.
OE M12x1.5 Front Hub Assembly: 3293g
FLM M14x1.25 Front Hub Assembly: 2957g (-0.74lbs per corner)
OE M12x1.5 Rear Hub Spindle: 1686g
FLM M14x1.25 Rear Hub Spindle: 1441g (-0.54lbs per corner)
Each hub kit comes pre-assembled, moly-coated, and includes everything you'll need for a truly plug and play retrofit*, including all new hardware.
NOTE: *OEM rotor hats and select aftermarket solutions may require drilling out rotor hats to accommodate M14 hardware. Please also verify your desired wheel set can accept M14. Stud Kit pictured is sold separately.
What is moly coating? Molybdenum Disulfide Coatings (MoS2 coatings), also known as Moly Coatings, are a dry film lubricant that are commonly used in applications where load carrying capacity, operating pressure and coefficient of friction are primary concerns. This coating provides effective lubrication in a wide range of loads, in many cases exceeding 250,000 psi. Moly coatings lubricate sacrificially by transferring lubricant between the two mating surfaces, which helps to reduce wear and coefficient of friction.
The E9X M3 / E82 1M have unquestionably become modern-day icons for their formidable street and track dominance. Both of these cars are equipped with M12x1.5 hardware from the factory, leaving them precariously prone to failure during rigorous track sessions and consequently, a potentially dangerous and damaging fate.
Fall-Line Motorsport has developed a hub retrofit kit that will convert your E9X M3 / E82 1M to the more robust M14x1.25 hardware as well as shave rotational mass from each corner.
OE M12x1.5 Front Hub Assembly: 3293g
FLM M14x1.25 Front Hub Assembly: 2957g (-0.74lbs per corner)
OE M12x1.5 Rear Hub Spindle: 1686g
FLM M14x1.25 Rear Hub Spindle: 1441g (-0.54lbs per corner)
Each hub kit comes pre-assembled, moly-coated, and includes everything you'll need for a truly plug and play retrofit*, including all new hardware.
NOTE: *OEM rotor hats and select aftermarket solutions may require drilling out rotor hats to accommodate M14 hardware. Please also verify your desired wheel set can accept M14. Stud Kit pictured is sold separately.
What is moly coating? Molybdenum Disulfide Coatings (MoS2 coatings), also known as Moly Coatings, are a dry film lubricant that are commonly used in applications where load carrying capacity, operating pressure and coefficient of friction are primary concerns. This coating provides effective lubrication in a wide range of loads, in many cases exceeding 250,000 psi. Moly coatings lubricate sacrificially by transferring lubricant between the two mating surfaces, which helps to reduce wear and coefficient of friction.
Prop 65 Warning
Product Q&A
Lifetime Replacement
This product is not eligible for Lifetime Replacement
Fits These Cars
MAKE
MODEL
SUBMODEL
ENGINE
Special Fitment Notes
BMW
E82
1 M Coupe
N54 3.0L
Use vehicle selector to confirm fitment
BMW
E90
M3
S65 4.0L
Use vehicle selector to confirm fitment
BMW
E92
M3
S65 4.0L
Use vehicle selector to confirm fitment
BMW
E93
M3
S65 4.0L
Use vehicle selector to confirm fitment
*The above product applications have been written by Turner Motorsport. All
warranties, product application, fitment, and performance are the responsibility of Turner Motorsport.
For additional information see the terms of use.
Prop 65 Warning
