BMW Tools & Specialty Equipment for BMW E12 530i M30 3.0L

This tool comes in handy especially when working with an engine harness. Certain areas are always prone to corrosion and this tool makes having to re-pin a connector a breeze.

Unlike small screwdrivers, picks, and paper clips, these tools are the correct size and shape to remove and install tiny electrical pins and terminals at plastic block connectors with ease, and will not damage the connectors in the process.

Packaged in a blow molded case to keep everything secure and organized.

PRESSURE BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

FLUID CATCH BOTTLE:

keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Here's what makes this floor jack the best on the market:

• Dual pump pistons to reach maximum height in 5 pumps
• Low profile design keeping lowered cars in mind
• Easy maneuverability 
• Two piece quick release padded handle for storage or transport.

Details:

• Jack Capacity 2 Ton
• Max Lift Height 20"
• Low Height 3.25"
• Chassis Length 26.5"
• Overall Width 13"
• Saddle Diameter 4.5"
• Handle Length 50"
• Shipping Weight 50 lbs

When doing work where the mounts and support need to be removed from the engine or transmission having a engine support bar is wise. By using this engine support the stress is coming off of whatever components are still attached reducing future unnecessary repairs. The safety side of it is having the heavy engine and transmission firmly supported as it should be instead of questionable jack techniques.  

Features:

•  2" longer than most
• Deluxe transverse support for even more stability
•  Two angle chain hooks for safer and more stable chain support 
•  61" long and fully adjustable to any width
•  Weight rating is a full 1000 lbs.
•  Includes four rubber padded feet to prevent slipping and damage to cars finish 
• This tool features a dual hook design for holding engine or transmission in place
•  Powder coated for long life and durability

Note: It is important that chains are hooked to both sides of hook, like in photo to insure load is supported evenly. 

This professional-grade deluxe fender roller allows you to gently and gradually flatten your inner fender lips in order to increase your fender to tire clearance.

This new deluxe fender roller has been designed to fit most applications.

This is the perfect tool for:

If you want to lower your vehicle
If you want wider-than-stock wheels
If you are going to use wheel spacers or decreased offset
Will work with bolt patterns of 4x100 and 5x100 up to 4x114.3 and 5x130 with 12mm or 14mm lug bolts.

By rolling the fender lip flat, you can lower your car further, and give your car a wider stance, without your tires rubbing on the inside of the fender.

Fully adjustable for use on vehicles of different ride heights, offsets, and wheel bolt patterns.

Use of a heat gun is recommended to soften the fender surface during the rolling process and prevent paint cracking.

EXTRACTOR:

The Schwaben 6.5 Liter Extractor empowers you with swift, hand-operated fluid extraction. Complete with two tubes of varying diameters to suit your unique needs, this system's vacuum release button guarantees seamless operation. Clearing 6.5 Liters (6.8 qts.) of fluid in minutes, it preserves a spotless, oil-free workspace. Its ingeniously designed pour spout ensures mess-free fluid disposal.

Features:

• Stability First: Equipped with a flip-out foot for steady usage, delivering precise extraction.
• Organized Efficiency: Integrated hose storage streamlines your extraction process.
• Perfectly Sized: A 41" main tube (3/8" OD) and two 35" extension tubes (1/4" and 3/16" OD) ensure versatility across applications.
• Beyond Extraction: It doubles as a brake bleeder with the optional ES3248036 Brake Bleeder Hose.
• LIFETIME REPLACEMENT: Like almost all Schwaben tools, this fluid extractor is backed by our lifetime replacement program should anything go wrong!

ADAPTER:

This adapter hose allows a quick and easy suction thru the bleeder screw. This hose has included shut off valve in hose.  This will improve your extractor capabilities and make it even more of an all-in-one tool!

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Looking to update your old torque wrenches? The Schwaben 3/8" Drive Digital Torque Wrench is your answer. 

This digital torque wrench uses an easy-to-read display to show torque amounts and settings, features a push button release, reversible 3/8" drive, 45 tooth ratchet head, and a comfortable no-slip grip and adjustment wheel.

Specifications:

• Setting Range: 45-220 ft lbs (60-300 Nm)
• Display Units: ft-lbs, N-m, Inch-lbs, cm-kg2, and m-kg
• Size: 22" (550mm) length for easy leverage
• Accuracy: +- 3%
• Include blow molded holding case
• Requires one 3V CR2030 battery (included)

When it comes to the torque found on axle nuts you're already looking at using a breaker bar or impact gun not to mention the corrosion collected over the years. The safest approach is using impact socket, since they are built with the strength needed to avoid breaking under pressure.

Features:

• Heavy duty ½ inch-drive sockets and drivers have extra thick alloy steel walls, and take a beating that would destroy normal sockets
•  Durable black oxide coating wipes clean easily and resists rust
• Contains three 12-point sockets for a sure grip on the most common sized axle nuts, plus three hex drives for removing common hex-head plugs and fasteners
• Conveniently packaged in a blow molded case, this set will please the most demanding professional technician or discriminating prosumer

Kit includes:

• 30mm, 32mm, and 36mm - 12-point axle nut sockets - ½" drive

• 14mm, 17mm, and 19mm hex head drive axle shoulder bolt sockets - ½" drive

This great Schwaben kit is designed to work on todays modern cars. Set contains popular torx and triple square bits found on a lot of German and other European cars. Designed to operate in minimal space situations.

Set Contains:

• 6 stubby triple square with 12 mm hex to be used with included 12 mm ratcheting wrench. 4 mm, 5 mm, 6 mm, 8 mm and 10 mm. 
• 4 stubby triple square with 19 mm hex to be used with included 19 mm ratcheting wrench.. 12 mm regular and  14 mm, 16 mm and 18mm tamper proof triple square.
• Set also includes a 3/8" drive 12 mm socket and 1/2" drive 19 mm socket to fit bits. Good for using bit with ratchet or torque wrench.
• 9 torx bits 10 to 70 torx 
• Includes blow molded case with sturdy foam insert to keep every thing in order.

3/8" DRIVE LONG FLEX HEAD RATCHET:

A professional quality flex ratchet features a fine satin finish designed for durability and easy clean up.

Features:

• Special designed 72T gear mechanism
• 5 degree of handle movement between gears 
• Flex head has 7 detent positions in a 180 degree swing
• Push button release holds socket tight until you are ready to release
• Ratchet is a full 290mm ( 11") long for extra leverage.

3/8" DRIVE 6 POINT SOCKET SET:

A satin chrome finish with a knurled ring around socket body, the knurling allows for a better grip when hands and sockets are covered in oil or grease. All sockets feature a radius in the corners for superior torque to the sides of the fastener, not the corner. Complete size coverage.

Includes:

• 8mm
• 9mm
• 10mm
• 11mm
• 12mm
• 13mm
• 14mm
• 15mm
• 16mm
• 17mm
• 18mm
• 19mm

LIFETIME REPLACEMENT on all items in this kit!

SPL Parts is a performance suspension manufacturer that designs and tests their products all in-house here in the USA. Additionally, all materials used are sourced from American suppliers to ensure consistently high quality products. SPL Parts products are all constructed using chromoly seamless straight tubing, DOM mandrel bent tubing, and 6061 and 2024 aluminum for high strength and quality. All TIG welding and CNC machining is also done locally by professional welders and machine shops to meet exact quality standards and tolerance specifications. For anything from racing to street driven needs, SPL Parts offer an amazing line of premium qulaity products that are perfect to get your car back in spec.

This wrench is the perfect addition to your tool box. Made specifically for the SPL hybrid adjusters, it will not damage the finish and is small enough to make the needed adjustments in very tight spaces. Plus, this adjustment wrench comes with a bottle opener built in! Great for cracking open a cold one in your garage or at the track. This wrench is black anodized for looks and corrosion resistance and, as always, is made in the USA!