BMW Tools & Specialty Equipment for BMW E12 530i M30 3.0L

PRESSURE BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

FLUID CATCH BOTTLE:

keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

WHEEL STORAGE RACK:

Now you can stack your extra wheels without the danger of scratches and scuffs. This wheel storage rack keeps your wheels spaced apart, and being on locking casters, allows you to easily move the whole set anywhere in your garage or shop at one time. Sturdy steel construction and a wide base means this wheel rack won't tip over. Holds up to 275 lbs - enough for most any wheel & tire set.

Fits up to 8½" wide wheels, depending on offset

TIRE STACK COVER:

This tire stack by Schwaben is the solution to keeping your tires and wheels clean while in storage.

• Works with 4 tire stacks and works great with our Schwaben Wheel Tree (ES2710754).
• Durable 150D coated material is rated for outdoor use.
• Cover is a large 32" wide X 46" tall.
• Fitted with a long 29" zipper up the side for easy installation and removal.
• Nylon draw string at the bottom allows for a good snug fit.
• Includes a handy storage pouch if not in use.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Wall Hangers Set is the ideal solution for organizing and storing QuickJack frames in a garage. Designed for those who prefer a clean and efficient storage solution, these hangers provide a convenient way to keep your portable car lift frames off the ground and out of the way. The hangers mount directly into a sturdy wall stud, ensuring safe and simple storage for all QuickJack models. Each mount is crafted with a sleek, laser-cut QuickJack logo, affirming its authenticity and quality.

• Secure storage: Mounts directly into wall studs for safe and stable hanging of QuickJack frames.
• Universal fit: Accommodates all QuickJack models, ensuring versatility and convenience.
• Durable construction: Over-engineered to 150% of the rated capacity for long-lasting durability.
• High-quality materials: Made from brushed steel for a robust and stylish appearance.
• Authentic design: Features a sleek, laser-cut QuickJack logo, reflecting its official status and rigorous engineering standards.
• Easy installation: Simple to install, with real-world testing and advanced computer analysis ensuring reliability and resilience.

Upgrade your garage organization with the Wall Hangers Set for a neat, secure, and professional storage solution for your QuickJack frames.

Due to clearance issues, many types of lifts require specific adapters that are made for reaching SUV and truck jack points. This 12-piece kit has been made by using stackable adapters that mount inside the lifting block trays so that vehicles with high ground-clearance or those with unique jack point locations are better accommodated. These adapters offer up to 7.2" of additional height when all combined.

Complete kit includes:

• Low‐profile round polyurethane contact pads  -  Qty: 4
• Sliding receivers that accommodate the round polyurethane contact pads and/or the stackable adapters  -  Qty: 4
• 3" stackable adapters.  -  Qty: 4

Fits BL-5000SLX/EXT and BL-7000SLX/EXT Series Only.

EXTRACTOR:

The Schwaben 6.5 Liter Extractor empowers you with swift, hand-operated fluid extraction. Complete with two tubes of varying diameters to suit your unique needs, this system's vacuum release button guarantees seamless operation. Clearing 6.5 Liters (6.8 qts.) of fluid in minutes, it preserves a spotless, oil-free workspace. Its ingeniously designed pour spout ensures mess-free fluid disposal.

Features:

• Stability First: Equipped with a flip-out foot for steady usage, delivering precise extraction.
• Organized Efficiency: Integrated hose storage streamlines your extraction process.
• Perfectly Sized: A 41" main tube (3/8" OD) and two 35" extension tubes (1/4" and 3/16" OD) ensure versatility across applications.
• Beyond Extraction: It doubles as a brake bleeder with the optional ES3248036 Brake Bleeder Hose.
• LIFETIME REPLACEMENT: Like almost all Schwaben tools, this fluid extractor is backed by our lifetime replacement program should anything go wrong!

ADAPTER:

This adapter hose allows a quick and easy suction thru the bleeder screw. This hose has included shut off valve in hose.  This will improve your extractor capabilities and make it even more of an all-in-one tool!

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

These QuickJack rubber contact blocks are used with all QuickJack systems and can be used with other QuickJack pads or are perfect to replace missing pads.

These blocks are made of a hardened rubber that has specifically been formulated to resist gouging, cutting, and abrasion. They are also resilient against chemicals and solvents that would normally damage rubber.

Dimensions: 6.5" long x 1.5" tall x 4" wide

• Tough and rigid expanded polystyrene foam (EPS) with a load rating of 1,500lbs per wheel (almost twice what the normal corner weight would be on a 3-series BMW)
• 12" height X 12" width with minimal compression under load
• Light weight with each block weighing less than 6lbs and with a handy strap for carrying or hanging
• Curved cradle for the tire to sit inside
• Non-skid surface that won't scratch your floor

Looking for an alternative to your jack stands? With these wheel blocks you won't have to think twice about a jack stand scratching or denting the underside of your floor or the car falling off the jack stand. These work best when used with a floor jack under the subframe and the opposite axle wheels chocked. These are also a light weight and inexpensive alternative to the super-pricey plastic and metal ramps. They are resistant to most fluids and chemicals (but not solvents) and will never rust unlike metal ramps and blocks.

Also available in a 10" height.

The Universal 40 Piece Metric Socket Set includes all of the necessary tools to create a socket set by purchasing only one ratchet. The included 3/8-inch drive flex head ratchet and two female 3/8-inch drive adapters will allow you to use 3 different drive sizes of sockets: 1/4", 3/8", and 1/2"! Use this kit to help complete your tool kit until you decide to purchase more ratchet sizes, and when you do, you don't have to get rid of any of these tools to do so, which is possible with the adapters.

And of course, this kit is included in our LIFETIME REPLACEMENT program!

Includes:

• 4 mm (1/4" Drive)
• 4.5 mm (1/4" Drive)
• 5 mm (1/4" Drive)
• 5.5 mm (1/4" Drive)
• 6 mm (1/4" Drive)
• 7 mm (1/4" Drive)
• 8 mm (1/4" Drive and 3/8" Drive)
• 9 mm (1/4" Drive and 3/8" Drive)
• 10 mm (1/4" Drive, 3/8" Drive, and 1/2" Drive)
• 11 mm (1/4" Drive and 3/8" Drive)
• 12 mm (1/4" Drive and 3/8" Drive, and 1/2" Drive)
• 13 mm (1/4" Drive and 3/8" Drive, and 1/2" Drive)
• 14 mm (1/4" Drive and 3/8" Drive, and 1/2" Drive)
• 15mm (3/8" Drive and 1/2" Drive)
• 16mm (3/8" Drive and 1/2" Drive)
• 17mm (3/8" Drive and 1/2" Drive)
• 18mm (3/8" Drive and 1/2" Drive)
• 19mm (3/8" Drive and 1/2" Drive)
• 21mm (1/2" Drive)
• 22mm (1/2" Drive)
• 24mm (1/2" Drive)

The Schwaben 24 Piece 1/2" Drive 6 Point Deep and Standard Socket Set comprises two dozen 1/2-inch metric sockets, each featuring 6-point heads specially crafted for navigating those tricky, confined spaces. With a length of 76mm, the deep sockets ensure you can reach critical areas with ease.

Furthermore, our LIFETIME REPLACEMENT program provides you with added assurance, ensuring enduring performance and value. Improve your toolkit with the Schwaben 24 Piece 1/2" Drive 6 Point Deep and Standard Socket Set and confidently tackle any task at hand.

Features:

Access Tight Spaces: These deep sockets, measuring 76mm in length, are expertly designed to reach challenging, confined areas, making them perfect for intricate tasks.

Organized Storage: Included in the set is a practical sliding rail socket holder, helping you maintain a tidy and easily accessible socket arrangement.

Enhanced Grip: Knurled rings encircling the socket bodies ensure a secure hold, even when hands and sockets are covered in oil or grease, minimizing the risk of accidents.

Optimal Torque: The sockets are equipped with corner radii for superior torque distribution, safeguarding fasteners from damage and ensuring efficient performance.

High-Quality Material: Crafted from robust chrome vanadium steel (CR-V), these sockets offer superior wear resistance and toughness compared to high-speed steel, guaranteeing durability and extended lifespan.

Satin Chrome Finish: Not only do the sockets feature an attractive satin chrome finish, but they also provide excellent corrosion resistance, ensuring long-term quality.

Lifetime Replacement: Supported by our lifetime replacement program, this set delivers enduring value and peace of mind, making it a wise addition to your toolkit investment.

Includes:

• 10 mm - deep and standard socket
• 12 mm - deep and standard socket
• 13 mm - deep and standard socket
• 14 mm - deep and standard socket
• 15 mm - deep and standard socket
• 16 mm - deep and standard socket
• 17 mm - deep and standard socket
• 18 mm - deep and standard socket
• 19 mm - deep and standard socket
• 21 mm - deep and standard socket
• 22 mm - deep and standard socket
• 24 mm - deep and standard socket

Aluminum 3-Ton Jack Stands With Mechanic's Folding Ground Pad - Set Of 2 are designed for exceptional performance and convenience in automotive maintenance. These lightweight aluminum jack stands provide robust support, while the mechanic's folding ground pad ensures comfort during vehicle work.

• Lightweight Construction: Each jack stand weighs only 4.7 lbs, making them easy to handle without sacrificing strength.
• Durable Design: All-aluminum construction with heavy-duty flanged bases ensures stability and safety for loads up to 3 tons.
• Adjustable Heights: Features 6 locking positions with a minimum height of 10.6 inches and a maximum height of 15.4 inches.
• Secure Load: Extra heavy-duty load pin with a posi lock ball mechanism keeps the pin securely in place.
• Large Base: Equipped with a 7-inch diameter base for enhanced stability.
• Mechanic’s Ground Pad: Provides comfort with high-density foam and a heavy-duty cover that resists oils and fluids. Measures 17"W x 47"L when unfolded and includes built-in carrying handles.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.