BMW Tools & Specialty Equipment for BMW E12 530i M30 3.0L

This tool comes in handy especially when working with an engine harness. Certain areas are always prone to corrosion and this tool makes having to re-pin a connector a breeze.

Unlike small screwdrivers, picks, and paper clips, these tools are the correct size and shape to remove and install tiny electrical pins and terminals at plastic block connectors with ease, and will not damage the connectors in the process.

Packaged in a blow molded case to keep everything secure and organized.

This professional-grade deluxe fender roller allows you to gently and gradually flatten your inner fender lips in order to increase your fender to tire clearance.

This new deluxe fender roller has been designed to fit most applications.

This is the perfect tool for:

If you want to lower your vehicle
If you want wider-than-stock wheels
If you are going to use wheel spacers or decreased offset
Will work with bolt patterns of 4x100 and 5x100 up to 4x114.3 and 5x130 with 12mm or 14mm lug bolts.

By rolling the fender lip flat, you can lower your car further, and give your car a wider stance, without your tires rubbing on the inside of the fender.

Fully adjustable for use on vehicles of different ride heights, offsets, and wheel bolt patterns.

Use of a heat gun is recommended to soften the fender surface during the rolling process and prevent paint cracking.

 This comprehensive kit is basically a one-stop-shop to pick up all the special torx, triple square, & hex bits you need to keep your car where it should be... on the road!

This Universal European Tool Kit features the following:

• Torx Screwdriver Kit - 6 Pieces (Sizes included: T10, T15, T20, T25, T27, & T30. Perfect for removing door and dashboard panels, interior trim, and smaller underhood components. )
• Swivel Head Triple Square Driver Kit - 4 Pieces (Set of four 3/8 drivers in M6, M8, M10, and M12 sizes. Perfect for working around corners in those hard to reach spots.)
• Specialty Bit Kit - 100 Pieces (100 piece torx & hex bit kit to fit a wide assortment of automotive fasteners. Made of hardened Chrome Vanadium steel, packaged in a handy blow molded case.)
• Go-Through Screwdriver Kit - 6 Pieces (Kit includes durable slotted & phillips head nickel-chromoly screwdrivers with hardened shafts that extend the entire length of the driver.)

When it comes to the torque found on axle nuts you're already looking at using a breaker bar or impact gun not to mention the corrosion collected over the years. The safest approach is using impact socket, since they are built with the strength needed to avoid breaking under pressure.

Features:

• Heavy duty ½ inch-drive sockets and drivers have extra thick alloy steel walls, and take a beating that would destroy normal sockets
•  Durable black oxide coating wipes clean easily and resists rust
• Contains three 12-point sockets for a sure grip on the most common sized axle nuts, plus three hex drives for removing common hex-head plugs and fasteners
• Conveniently packaged in a blow molded case, this set will please the most demanding professional technician or discriminating prosumer

Kit includes:

• 30mm, 32mm, and 36mm - 12-point axle nut sockets - ½" drive

• 14mm, 17mm, and 19mm hex head drive axle shoulder bolt sockets - ½" drive

This great Schwaben kit is designed to work on todays modern cars. Set contains popular torx and triple square bits found on a lot of German and other European cars. Designed to operate in minimal space situations.

Set Contains:

• 6 stubby triple square with 12 mm hex to be used with included 12 mm ratcheting wrench. 4 mm, 5 mm, 6 mm, 8 mm and 10 mm. 
• 4 stubby triple square with 19 mm hex to be used with included 19 mm ratcheting wrench.. 12 mm regular and  14 mm, 16 mm and 18mm tamper proof triple square.
• Set also includes a 3/8" drive 12 mm socket and 1/2" drive 19 mm socket to fit bits. Good for using bit with ratchet or torque wrench.
• 9 torx bits 10 to 70 torx 
• Includes blow molded case with sturdy foam insert to keep every thing in order.

BMW essentials from drivetrain work to fluid changes.

Features:

• 36mm 12-point deep socket, 1/2" drive - Used on axle nuts and most BMW oil filter housing nuts
• 30mm 12-point deep socket, 1/2" drive - Used on driveshaft and pinion mounting, rear wheel bearing removal and reinstallation on many BMWs
• 27mm 6-point socket, 1/2" drive - Fits N52/54 oil filter housing nuts and other various places on most BMWs
• 14/17mm service wrench - Versatile wrench features an open end and a hex head driver that fit most BMW transmission fill/drain plugs. Perfect for engine and transmission oil drains.
• M18 triple square extended reach socket, 1/2" drive - Used to remove axles and other various driveline components.
• All of the sockets included in this kit are built with extreme durability and versatility in mind, and can be used with breaker bars and impact guns.

If you're refreshing your struts and springs this tool is a must, properly compress the springs, easily remove and install the strut nut, and smoothly remove the spindles.

Features:

• Spring Compressor
• Strut Nut Sockets
• Spindle Spreader

To secure shocks and struts to their mounts, the retaining nut must be torqued to its proper specification using a torque wrench. An improper torque value may result in premature mount failure - or worse. Strut nut sockets allow for the use of an allen wrench to hold the damper shaft while utilizing your 1/2" drive torque wrench on the socket to achieve proper torque.

Kit Features:

• 18mm
• 19mm
• 21mm
• 22mm
• 24mm

Engineered for optimal comfort and ease of movement, this reclining creeper seat is ideal for anyone working under vehicles. Its gas spring-supported backrest offers adjustable reclining from 0° to 70°, with seat angles shifting in 10° increments up to 30°, delivering superior ergonomics for mechanics and hobbyists alike.

Equipped with six 360° swivel casters, this creeper seat glides effortlessly around the workspace, allowing you to move smoothly without constantly adjusting your position, helping you stay focused on the job.

Constructed from heavy-duty materials, the seat is upholstered with non-slip, marine-grade vinyl, resistant to abrasion, chemicals, and oil. This durable design provides long-lasting comfort and is the perfect addition to your garage setup.

Features:

• TPR wheels feature a shock absorbing cushioned ride, while providing good floor protection and quiet rolling operation
• TPR wheels are resistant to chemicals, acids, alcohol, and water
• Wide, large diameter wheel improves rolling over rough surfaces
• Heavy-duty non-slip textured marine grade vinyl
• Comfortable thick-padded seat and backrest
• Locking casters
• Seat is resistant to abrasion, chemical, and oil

Specifications:

• Length (Backrest Up): 33 in. / 840 mm
• Length (Backrest Down): 45.25 in. / 1,150 mm
• Width (Frame): 17 in. / 430 mm
• Width Overall: 20.75 in. / 530 mm
• Seat Height (Down): 6.25 in. / 161 mm
• Backrest Height (Up): 31.5 in. / 800 mm
• Seat/Backrest Width: 14.75 in. / 376 mm
• Ground Clearance: ≈3 in. / 76 mm
• Seat Angle Min. / Max.: ≈0° to 30°
• Maximum Load: 600 lbs. / 272 kg.
• Backrest Angle Adjustment: Gas spring
• Seat Angle Adjustment: Mechanical Lock — 3 positions
• Casters: Six 360° Casters, ø2.5 in x .75 in., sleeve bearings, oil resistant, non-marring rubber wheels.
• Seat Materials: Padded Marine Vinyl Backrest and Seat. Marine Vinyl is abrasion, chemical and oil resistant.
• Frame Materials: Full powder coated, welded steel square tube
• Weight: 41.25 lbs. / 19 kg.
• Backrest Angle Min. / Max.: ≈0° to 70°