BMW Suspension Parts for BMW 3 Series E30 (1984-1991)

Swapping in E46 control arms into your E30 or E36 significantly increases negative camber by widening the track width and also gives you more clearance for more steering angle. Condor's CNC machined control arm brackets are made from solid steel and are fitted with a solid hex-shaped bushing. Designed for the street or the track, they hold the control arm steady and eliminate "shimmy" caused by stock bushings. They sharpen steering and improve overall driving feel. Comparable to the NLA Treehouse E36 & E30 Eyeball Arms.

Easiest install of any aftermarket solution
Allow clearance for E30 M50 Conversion exhaust
Street Approved, marginal increase in NVH
Easy Installation, no need for a press
CNC machined steel construction
Solid design without the maintenance of spherical bearings
Heavy-Duty replaceable UHMW insert. Don't be misinformed, UHMW is the best material for these inserts. Delrin is not self-lubricating and will crack and degrade over time.
Powder coated white for corrosion resistance
Improve caster with M3 offset geometry
Keep proper steering geometry under high loads
Made in the U.S.A.
Fitment:
E30 84-91 3 Series
E36 92-98 3 series & Z3

Note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36

Be sure to measure your control arms to determine if you need 21mm or 23mm. Meyle makes a standard e46 control arm and a Heavy Duty control arm. Most HD arms have a hex that is larger in size (23mm). Lifetime Warranty

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 2 kit replaces:

Front Sway Bar End Links
Front Upper Strut Mounts
Control Arms w/ Bushings
Control Arm Brackets w/ M3 Control Arm Bushings
Outer Tie Rods

If E30 needs a little more pep in the corners, this is an excellent suspension package. H&R Sport springs and Bilstein Sport shocks for the E30 will lower the ride height for an aggressive stance and stiffer springs will improve handling and balance in the corners. This suspension is a favorite among our E30 fans because the car corners better without a punishing ride. Perfect for daily-driven E30s who want to carry more speed through the corners.

H&R Sport springs lower the ride height by 1.25" and stiffens the spring rate. Both combine to lower the car's center of gravity and reduce the amount of bodyroll in corners. The springs are progressive rate so their initial stiffness is actually very compliant and it becomes stiffer as the spring is compressed. This is great for street cars that see bumps and potholes where suspension compliance is key. Overall, they are about 40% stiffer than the stock original springs.

We use Bilstein Sport shocks as the dampers and they feature Bilstein's patented and innovative valving system. With this system, small bumps and impacts are absorbed as they should be. But the shocks stiffen for cornering and other suspension motions. It's the best of both worlds as the shock self-adjusts based on suspension motion. These fit with the stock strut and shock mounts, making for an easy and clean install.
 

Parts list:

• 1 set - H&R Sport Springs (50406)
• 1 pair - Bilstein Front Sport strut inserts (P36-0335 / 34-003350)
• 1 pair - Bilstein Rear Sport Shocks (B36-2027 / 24-020275)

Fitment note: Front strut inserts fit the larger 51mm strut housings. These were standard for all 6-cylinder E30s, all M3, and 1989-1992 318i/is. Other models used a smaller strut housing which requires a different Bilstein insert.

This item fits the following BMWs:
1984-1992 E30 BMW 325e 325es 325i 325ic 325is

This kit is contains all new strut and shock mounts and hardware needed when installing a new shocks and struts or aftermarket suspension on your vehicle. 

Fits the following BMW's

BMW E30 318i 318is 325 325e 325es 325i 325is M3

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 2 kit replaces:

Sway Bar End Links
Reinforcement Plates
Shock Mounts & Gaskets
Differential Mount Bushing
Trailing Arm Bushings
Subframe Bushings

Looking to upgrade your front suspension to increase the strength and your steering angle for the track? IRP has you covered with their BMW Lock Kit. This kit includes new control arms that are stronger than stock, are a chromolon tubular system, and have monoball ball joints, new tie rod ends that feature steel monoball ball joints as well, new offset control arm bushings, fully adjustable camber plates, roll center/bump steer correction plates, and all new hardware. This enables this kit to be fully plug and play, giving you a much more adjustable front suspension, and increases the total amount of steering angle up to 70 degrees.

This kit is perfect for those looking to build a drift car and ensure their suspension is ready to take on the challenge.

*This Pro kit offers reduced weight control arms that help this kit shed 2.9 lbs from the standard kit while still remaining just as strong thanks to their chromolon tubular design.*

Kit features:

• CNC Laser Cut Components
• Plug & Play - includes all needed hardware
• Increase to 70 Degree (or more) steering angle (5 degrees more than standard version)
• Includes Camber Plates
• Stiffer offset control arm bushings
• Roll Center and Bump Steer Correction Plates
• High Strength chromolon tubular control arms with steel monoball ball joints (2cm wider than standard version)
• Increased length steering tie rods with steel monoball ball joints
• DriftAllstar- & EEDC-Tested
• Total weight of all components included: 12.2kg / 26.9lbs (1.3kg / 2.9lbs lighter that standard version)

Fits the following BMWs:
1982-1991 E30 BMW All RWD Submodels