BMW Brakes & Brake Parts for BMW 5 Series E34 (1987-1995)

This caliper bushing kit will eliminate flex caused by weak rubber caliper bushings. As the brake pedal is pressed the caliper grabs the rotor and twists on its mounting bushings. The rubber bushings allow the caliper to deflect and twist which affects pedal feel and results in uneven pad wear. These solid brass bushings will not twist or deflect so your calipers can squeeze the pads evenly on both sides of the rotor (sort of like what multi-piston big brakes do). This will give you much longer pad life and a more consistent pedal feel. This is the most complete kit we have ever sold with stainless steel caliper slide bolts, o-rings, and new dust boots. Unlike other kits, these bushings are pressed into the caliper and will not shift or slide on their own.

Installation is straightforward: remove the old rubber bushings and press in the new brass bushings (we recommend special tool 003326ECS03). High temp caliper grease or anti-seize is required. The new bushings include an inner o-ring that helps trap grease on the slide bolt, reducing friction and wear.

***Click here for installation instructions*** 

***Click here for the installation tool***

For most models with floating calipers. Fits the rear of E90/2 and E60, but for the front you'll need the kit found here. Does not fit E30 models with Girling calipers, but is compatible with Ate calipers. 

Pagid's newest sprint racing pad was developed for racing cars achieving very high average speeds with short braking distances and functional aero. The RST pads feature very high friction levels for the quickest bite and highest fade resistance than any other Pagid pad. RST pads are broken into 5 levels and all have ranging bite and release characteristics. RST pads will trade low wear for torque output and faster response. These were developed based on the needs of race engineers in World Challenge, Daytona Prototype, and GTLM where functional aero meant high grip in the corners and smaller braking zones.

RST Brake Pad Types:

• RST1 -  Very high friction coefficient, high initial bite, progressive torque curve, very high fade resistant
• RST2 - Medium high friction coefficient, good initial bite, mild progressive torque curve, good pedal feel
• RST3 - High friction coefficient, good initial bite, low heat conductivity, excellent modulation and release characteristics
• RST4 - Medium friction coefficient, good initial bite, mild progressive torque curve, high heat tolerance with consistent feel
• RST5 - Optimum thermal management, absolutely fluid fade resistant, highly developed recovery properties, extremely high friction coefficient

This item fits the following BMWs:
1995-1998 E36 BMW M3 
2001-2006 E46 BMW 330i M3 
1989-1995 E34 BMW 525i 530i 535i 540i M5 
1988-1994 E32 BMW 735i 735il 740i 740il 750il 
1997-2002 Z3 BMW M Roadster M Coupe
2006-2008 Z4 BMW M Roadster M Coupe

The latest in the Yellow line takes all of the RSL29 characteristics and adds a bit more aggressive behavior. Friction levels go up for more initial bite and better fade resistance. Modulation and release stays close to RSL29 levels. Pad and rotor wear is a little more than on the previous Yellows but still within reasonable levels and the RSL1 is still considered an extended endurance pad. Its development stemming from GT classes at Le Mans and Nürburgring.

Since Pagid pads tend to "out-gas" we recommend using these pads with a new gas-slotted or cross-drilled rotor for the best performance. Pagid brake pads are not compatible with previously used rotors, especially if used with a carbon or Kevlar based race pad.

This item fits the following BMWs:
1995-1998 E36 BMW M3 
2001-2006 E46 BMW 330i M3 
1989-1995 E34 BMW 525i 530i 535i 540i M5 
1988-1994 E32 BMW 735i 735il 740i 740il 750il 
1997-2002 Z3 BMW M Roadster M Coupe
2006-2008 Z4 BMW M Roadster M Coupe