BMW Suspension Parts for BMW E36 (1992-1998) M3

TC Kline Racing, a leader in BMW performance parts, delivers unparalleled street and track performance with their Double-Adjustable Coilover Suspension Kit for the E36 3er. This kit combines cutting-edge technology and premium materials to elevate your driving experience to new heights.

Key Features:

Smart Shock technology for optimal performance VVS alloy springs (300# front, 400# rear) Koni double-adjustable cartridges for seamless street to race transitions Camber/caster plates for supreme adjustability Ride height adjustability for personalized setup BUNA rubber RSMs for reduced flex This comprehensive kit includes:

8711-1007LSPTC - TCK/Koni Coilover Driver’s Side Strut 8711-1007RSPTC – TCK/Koni Coilover Passenger’s Side Strut TCKFSXXXS – TCK VVS Alloy Short Front Springs (300#F/400#R) 8242-1007L/RSPTC – TCK/Koni Double Adjustable Rear Shocks TCKRSXXX – TCK VVS Alloy Rear Springs (customized rates) TCKRUM12R – Pair of Reinforced BUNA Rubber Shock Mounts (12mm sleeve) TCKRSA – Pair of TCK Rear Spring Adjusters Camber Plates - 1 pair Experience the ultimate blend of performance and value with TC Kline Racing's Double-Adjustable Coilover Suspension Kit.

Take total control of your E36's handling with the ECS Performance 2-Way Adjustable Coilover System. Built specifically for track use, this system bridges the gap between standard off-the-shelf coilovers and full-fledged motorsport suspension. These coilovers feature independent compression and rebound controls supported by external reservoirs; unlocking the precision tuning needed to shave seconds off your lap times.

Traditional 1-way coilovers force a single adjustment knob to balance both bump and rebound. These 2-way dampers eliminate that trade-off with fully independent compression and rebound controls. Use the 32 levels of compression adjustment to control front weight transfer under heavy braking, maximizing entry grip and allowing you to trail-brake deep into corners without understeer. 22 rebound levels fine-tune chassis recovery on brake release, keeping the front tires loaded through the apex for faster power-on exit speeds.

To maintain consistent performance during extended periods of performance driving, these dampers feature dedicated external fluid reservoirs that significantly increase total gas volume. During rigorous track use, rapid piston movement generates intense friction and heat, causing standard damper oil to thin out, aerate, and lose its damping force. By increasing overall fluid capacity, the external reservoirs effectively dissipate heat to keep peak oil temperatures down.

Stock rear lower control arms offer very little adjustment for alignment, especially in lowered vehicles, due to their use of an eccentric bolt. These aftermarket performance control arms from ECS Tuning are designed for maximum adjustability, allowing you to maximize handling and minimize tire wear.

To ensure maximum reliability, ECS Tuning's control arms are constructed from strong, lightweight 6061-T6 aluminum and feature a 303 stainless steel center turnbuckle that offers over 8 degrees of fast and precise camber adjustment. The inner bushing is a stock style serviceable OEM bushing for long life and inexpensive maintenance.

Features:

Durable construction suitable for the daily driver and track car alike
8+ degrees adjustment range for dialing in any suspension and wheel/tire setup
Center located adjuster for maximum clearance during adjustment
OEM-style bushing for long life and inexpensive service
Black anodized 6061-T6 aluminum with 303 stainless steel turnbuckle
Includes new hardware
*With the exception of the stance community, most enthusiasts will need no more than a few degrees of adjustment range. Total adjustment often is dependent on wheel/tire clearances.

The E36/E46 rear trailing arm bushings (RTABs) wear out faster than any other bushing on the car. Worn RTAB will cause excessive toe alignment change and give a 'loose' or 'floaty' feeling in the rear handling. One of the reasons for this is that they over-extend during motion, stretching and twisting the rubber in all directions. These shims sit on either side of the bushing and limit the amount of extension from the bushing. Not only will you get more life from your RTAB but these will help stiffen the bushing during cornering. But during normal driving you will still have all of the comfort of the stock rubber bushings. These part about these bushings is how easy they are to install - simply slide them in place during your bushing install. They can be added to pre-installed bushings too by dropping the trailing arm and removing the cage around the bushing.

Works with stock rubber bushings only (not urethane or Delrin).

Urethane mounts keep the differential from twisting under load. As torque is put through the driveline it causes anything to twist and move. The differential is mounted to the subframe and the twisting and deflection can be transferred to the rest of the chassis. With a stiffer mount the differential will not deflect as much. This improves seat-of-the-pants feeling to the driver, giving more feedback for smoother power delivery. In theory, there's also more torque being sent to the drive wheels since it's not being used up shifting the diff weight around.

These are tough 88A durometer urethane bushings with a anodized almunum center sleeve, engineered by ECS. This is a set of E36 diff bushings - 1 for the front and 2 for the rear cover. New high-grade hardware is included (the front bolt has a tendency to snap from all that torque twisting!).

These SPL parts adjustable rear camber arms replace OEM part number 33326770813

SPL Parts is a performance suspension manufacturer that designs and tests their products all in-house here in the USA. Additionally, all materials used are sourced from American suppliers to ensure consistently high quality products. SPL Parts products are all constructed using 6061-T6 aluminum tubing, DOM mandrel bent tubing, and 6061 and 2024 aluminum for high strength and quality. All TIG welding and CNC machining is also done locally by professional welders and machine shops to meet exact quality standards and tolerance specifications. For anything from racing to street driven needs, SPL Parts offer an amazing line of premium quality products that are perfect to get your car back in spec.

These rear camber arms allow for significantly greater camber adjustment over stock, a major benefit to lowered cars that need their camber readjusted to prevent tire wear and poor handling. These camber arms also provide increased stability and predictability versus the stock camber arms with rubber bushings.

Technical Specifications:

• Lightweight Aluminum, Titanium, and Chromoly construction
• Anodized Black for corrosion protection and durable finish
• Gundrilled center hex links for maximum weight savings
• Teflon lined FK Rod Ends
• Made in the USA

Fits the following BMWs:
1992-1999 E36 BMW All Submodels
1999-2006 E46 BMW RWD Models

The Stage 1 Suspension System system consists of a set of performance tuned springs and carefully matched Koni adjustable front strut assemblies and rear shocks. The system provides superior handling through increased grip and reduction of body roll while maintaining a nicely dampened ride. The modestly lower ride height gives the car a tastefully enhanced performance look as well as improving suspension geometry. 

This item fits the following BMWs: 
1996-1999 E36 BMW M3 Sedan and Coupe