TC Kline Racing, a leader in BMW performance parts, delivers unparalleled street and track performance with their Double-Adjustable Coilover Suspension Kit for the E36 3er. This kit combines cutting-edge technology and premium materials to elevate your driving experience to new heights.

Key Features:

Smart Shock technology for optimal performance VVS alloy springs (300# front, 400# rear) Koni double-adjustable cartridges for seamless street to race transitions Camber/caster plates for supreme adjustability Ride height adjustability for personalized setup BUNA rubber RSMs for reduced flex This comprehensive kit includes:

8711-1007LSPTC - TCK/Koni Coilover Driver’s Side Strut 8711-1007RSPTC – TCK/Koni Coilover Passenger’s Side Strut TCKFSXXXS – TCK VVS Alloy Short Front Springs (300#F/400#R) 8242-1007L/RSPTC – TCK/Koni Double Adjustable Rear Shocks TCKRSXXX – TCK VVS Alloy Rear Springs (customized rates) TCKRUM12R – Pair of Reinforced BUNA Rubber Shock Mounts (12mm sleeve) TCKRSA – Pair of TCK Rear Spring Adjusters Camber Plates - 1 pair Experience the ultimate blend of performance and value with TC Kline Racing's Double-Adjustable Coilover Suspension Kit.

Take total control of your E36's handling with the ECS Performance 2-Way Adjustable Coilover System. Built specifically for track use, this system bridges the gap between standard off-the-shelf coilovers and full-fledged motorsport suspension. These coilovers feature independent compression and rebound controls supported by external reservoirs; unlocking the precision tuning needed to shave seconds off your lap times.

Traditional 1-way coilovers force a single adjustment knob to balance both bump and rebound. These 2-way dampers eliminate that trade-off with fully independent compression and rebound controls. Use the 32 levels of compression adjustment to control front weight transfer under heavy braking, maximizing entry grip and allowing you to trail-brake deep into corners without understeer. 22 rebound levels fine-tune chassis recovery on brake release, keeping the front tires loaded through the apex for faster power-on exit speeds.

To maintain consistent performance during extended periods of performance driving, these dampers feature dedicated external fluid reservoirs that significantly increase total gas volume. During rigorous track use, rapid piston movement generates intense friction and heat, causing standard damper oil to thin out, aerate, and lose its damping force. By increasing overall fluid capacity, the external reservoirs effectively dissipate heat to keep peak oil temperatures down.

If you are looking for a wider range of camber adjustability in the rear of you car, the IRP Adjustable rear lower control arm is exactly what you need! Built to be much stronger than stock, these rear control arms feature inner monoball bushings and are built of steel, reducing the weight as well. These are perfect for a lowered car or for a track car that needs a greater level of rear adjustment.

Features:

• Strong Steel Construction
• Adjustable
• Painted Yellow For Corrosion Protection
• Weight Reduction
• Monoball Inner Mount

This item fits the following BMWs:
1992-1999 E36 BMW 318i 318is 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2006 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

The E36/E46 rear trailing arm bushings (RTABs) wear out faster than any other bushing on the car. Worn RTAB will cause excessive toe alignment change and give a 'loose' or 'floaty' feeling in the rear handling. One of the reasons for this is that they over-extend during motion, stretching and twisting the rubber in all directions. These shims sit on either side of the bushing and limit the amount of extension from the bushing. Not only will you get more life from your RTAB but these will help stiffen the bushing during cornering. But during normal driving you will still have all of the comfort of the stock rubber bushings. These part about these bushings is how easy they are to install - simply slide them in place during your bushing install. They can be added to pre-installed bushings too by dropping the trailing arm and removing the cage around the bushing.

Works with stock rubber bushings only (not urethane or Delrin).

Urethane mounts keep the differential from twisting under load. As torque is put through the driveline it causes anything to twist and move. The differential is mounted to the subframe and the twisting and deflection can be transferred to the rest of the chassis. With a stiffer mount the differential will not deflect as much. This improves seat-of-the-pants feeling to the driver, giving more feedback for smoother power delivery. In theory, there's also more torque being sent to the drive wheels since it's not being used up shifting the diff weight around.

These are tough 88A durometer urethane bushings with a anodized almunum center sleeve, engineered by ECS. This is a set of E36 diff bushings - 1 for the front and 2 for the rear cover. New high-grade hardware is included (the front bolt has a tendency to snap from all that torque twisting!).

**For vehicles with stock style springs**

When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height. 

The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.

Features:

• Decreased understeer
• Decreases outside edge tire wear
• Aircraft Grade Aluminum Construction
• Steel Monoball and Mounting Sleeves

Fits the following BMWs:
1991-1999 E36 BMW

**For vehicles with coilover front suspension**

When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height. 

The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.

Features:

• Decreased understeer
• Decreases outside edge tire wear
• Aircraft Grade Aluminum Construction
• Steel Monoball and Mounting Sleeves

Fits the following BMWs:
1991-1999 E36 BMW

Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left- and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 175mm (6.89") to 235mm (9.25") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints (M10x1.5): Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability NOTE: If you've modified your vehicle's suspension with aftermarket struts or coilovers, the mounting location for the sway bar end link may have moved. To confirm fitment with our adjustable end links, please measure the distance between the sway bar and the mounting location on the strut body with the vehicle at ride height and confirm that it is within the 175 - 235mm range of adjustment.

A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides. 

The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection and to add to the looks of the engine bay.

Easily installed with basic hand tools.

Fits the following BMW chassis:
E36 BMW All Submodels

Looking to upgrade your front suspension to increase the strength and your steering angle for the track? IRP has you covered with their BMW Lock Kit. This kit includes new control arms that are stronger than stock, are a chromolon tubular system, and have monoball ball joints, new tie rod ends that feature steel monoball ball joints as well, new offset control arm bushings, fully adjustable camber plates, roll center/bump steer correction plates, and all new hardware. This enables this kit to be fully plug and play, giving you a much more adjustable front suspension, and increases the total amount of steering angle up to 70 degrees.

This kit is perfect for those looking to build a drift car and ensure their suspension is ready to take on the challenge.

*This Pro kit offers reduced weight control arms that help this kit shed 2.9 lbs from the standard kit while still remaining just as strong thanks to their chromolon tubular design.*

Kit features:

• CNC Laser Cut Components
• Plug & Play - includes all needed hardware
• Increase to 70 Degree (or more) steering angle (5 degrees more than standard version)
• Includes Camber Plates
• Stiffer offset control arm bushings
• Roll Center and Bump Steer Correction Plates
• High Strength chromolon tubular control arms with steel monoball ball joints (2cm wider than standard version)
• Increased length steering tie rods with steel monoball ball joints
• DriftAllstar- & EEDC-Tested
• Total weight of all components included: 12.2kg / 26.9lbs (1.3kg / 2.9lbs lighter that standard version)

Fits the following BMWs:
1992-1999 E36 BMW All Submodels