BMW Suspension Parts for BMW E36 (1992-1998) M3

Take total control of your E36's handling with the ECS Performance 2-Way Adjustable Coilover System. Built specifically for track use, this system bridges the gap between standard off-the-shelf coilovers and full-fledged motorsport suspension. These coilovers feature independent compression and rebound controls supported by external reservoirs; unlocking the precision tuning needed to shave seconds off your lap times.

Traditional 1-way coilovers force a single adjustment knob to balance both bump and rebound. These 2-way dampers eliminate that trade-off with fully independent compression and rebound controls. Use the 32 levels of compression adjustment to control front weight transfer under heavy braking, maximizing entry grip and allowing you to trail-brake deep into corners without understeer. 22 rebound levels fine-tune chassis recovery on brake release, keeping the front tires loaded through the apex for faster power-on exit speeds.

To maintain consistent performance during extended periods of performance driving, these dampers feature dedicated external fluid reservoirs that significantly increase total gas volume. During rigorous track use, rapid piston movement generates intense friction and heat, causing standard damper oil to thin out, aerate, and lose its damping force. By increasing overall fluid capacity, the external reservoirs effectively dissipate heat to keep peak oil temperatures down.

Stock rear lower control arms offer very little adjustment for alignment, especially in lowered vehicles, due to their use of an eccentric bolt. These aftermarket performance control arms from ECS Tuning are designed for maximum adjustability, allowing you to maximize handling and minimize tire wear.

To ensure maximum reliability, ECS Tuning's control arms are constructed from strong, lightweight 6061-T6 aluminum and feature a 303 stainless steel center turnbuckle that offers over 8 degrees of fast and precise camber adjustment. The inner bushing is a stock style serviceable OEM bushing for long life and inexpensive maintenance.

Features:

Durable construction suitable for the daily driver and track car alike
8+ degrees adjustment range for dialing in any suspension and wheel/tire setup
Center located adjuster for maximum clearance during adjustment
OEM-style bushing for long life and inexpensive service
Black anodized 6061-T6 aluminum with 303 stainless steel turnbuckle
Includes new hardware
*With the exception of the stance community, most enthusiasts will need no more than a few degrees of adjustment range. Total adjustment often is dependent on wheel/tire clearances.

Elevate Your BMW's Performance with ECS Tuning's Ultimate Performance Rear Shock Mount Kit

ECS Tuning presents the Ultimate Performance Rear Shock Mount Kit, specifically designed to address recurring rear shock mount blowouts experienced by various BMW models, including the M3 and non-M 3 Series dating back to the E30 chassis in 1984. This innovative kit provides a long-term solution, ensuring optimal damper performance and longevity while eliminating rear clunking noises and handling issues caused by blown shock mounts.

Key Benefits:

• Solves rear shock mount blowout issues on BMW models
• Allows full articulation of rear dampers for improved performance
• Industry-first design with PTFE lined stainless steel monoball spherical bearing
• 80A polyurethane isolation bushings reduce noise, vibration, and harshness (NVH)
• Lower dust seal enhances bearing life by preventing road debris ingress
• Corrosion-resistant anodized 6061-T6 construction for durability
• Compatible with 10mm, 12mm, or 14mm damper shafts

Upgrade your BMW's rear shock mounts with ECS Tuning's Ultimate Performance Rear Shock Mount Kit, providing superior performance, reduced NVH, and increased bearing longevity for a more controlled and comfortable ride.

Want a race-spec rear shock mount but with the comfort of a factory bushing? This ECS rear shock mount combines the precision and articulation of a spherical bearing with the isolation of urethane bushings. The stainless monoball bearing is lined with PTFE lubricant and suspended in 80A urethane and housed in a hard anodized 6061-T6 aluminum mount. The spherical bearing is a better design than most rear shock mounts because it allows the shock to move and tilt without side-loading the shock shaft (which leads to premature failure of the shock). Most Genuine BMW and aftermarket shock mounts are not designed for shock angles and the stress that track or performance driving will put on the shock shaft. The ECS shock mount is properly designed to handle these loads. The internal bearing is also replaceable - it will be years before you have to replace the entire mount. The ECS mount is fully encapsulated to prevent the common shock mount failure of the stock mount design.

ECS RSM features:

• Maintenance free, PTFE lined, stainless steel monoball spherical bearing for full shaft articulation
• 80A polyurethane isolation bushings for NVH control
• Accommodates 10mm, 12mm, or 14mm damper shafts
• Fully constrained shaft mount makes RSM blow out impossible
• Hard anodized 6061-T6 construction
• Fully rebuildable design

* - the RSM comes with the BMW standard 10mm shock shaft bushings. 12mm is used on some performance shocks and 14mm is used on some true motorsport rear shocks.

This strut and shock mount package covers the front and rear rubber mounts and bushings commonly replaced during a strut and shock install. While you're installing new front struts and rear shocks these are easily installed - there's no additional labor and special tools are not required. Since these pieces are mostly rubber, they dry up and crack over time. Re-using them lead to problems with fitment or noise, and may have safety issues as well. These mounts and pads are the perfect complement to your new shocks to help restore your car's handling and performance.

We sell the basic strut and shock mount package, which includes:

• Front strut mounts (also known as guide support)
• Front strut reinforcement plates (to prevent cracking and deforming of the front strut towers)
• Front strut tower paper washer gaskets
• Front and rear self-locking mounting nuts
• Rear Lifetime Warranty 'Repair Shop' shock mounts
• Rear shock mount reinforcements (to prevent cracking of shock towers)
• Rear shock mount gaskets

In addition, you can add the front spring pads, front bump stops, front dust boots, rear bump stops, and rear dust boots if needed. But please note that some shocks and coil overs come with all or some of these pieces already. If in doubt, check with your supplier on what is included.

We offer three varieties of the rear shock mounts - OEM, Repair Shop, and HP alum-rubber. We recommend either the Repair Shop or HP mounts because the stock OEM design has a flaw that can lead to premature failure of the mounts. The Repair Shop and HP mounts use a different design that will last longer and the Repair Shop mounts also have a lifetime warranty!

This item fits the following BMWs:
1996-1999 E36 BMW M3
1996-2002 Z3 BMW 2.5 2.5i 2.8 3.0i M Coupe

This kit is contains all new strut and shock mounts and hardware needed when installing a aftermarket suspension on your vehicle.

Click here for spring options  

Fits the following BMW's

1996-1999 BMW M3