Location: Front Type: Street, Stage 1 Bearing: captive-ball fully encased in polyurethane
These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.
Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.
This item fits the following BMWs: 2008-2012 E82 BMW 128i 135i 6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi 2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan 2006-2012 E91 BMW 328i - Wagon 2007-2013 E92 BMW 328i 335i 335is - Coupe 2007-2013 E93 BMW 328i 335i - Convertible 1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC) 2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i 2004-2011 E63 E64 BMW 645ci 650i 1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe 2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si 2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is 2000-2003 E52 BMW Z8 Roadster (without EDC)
Show More Show Less
Location: Front Type: Street/Track, Stage 2 Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch
The Stage 3 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.
Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.
This item fits the following BMWs: 2008-2012 E82 BMW 128i 135i 6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi 2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan 2006-2012 E91 BMW 328i - Wagon 2007-2013 E92 BMW 328i 335i 335is - Coupe 2007-2013 E93 BMW 328i 335i - Convertible 1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC) 2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i 2004-2011 E63 E64 BMW 645ci 650i 1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe 2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si 2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is 2000-2003 E52 BMW Z8 Roadster (without EDC)
Show More Show Less
Location: Front Type: Street/Track, Stage 2 Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch
The Stage 2 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.
Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.
This item fits the following BMWs: 2008-2012 E82 BMW 128i 135i 6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi 2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan 2006-2012 E91 BMW 328i - Wagon 2007-2013 E92 BMW 328i 335i 335is - Coupe 2007-2013 E93 BMW 328i 335i - Convertible 1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC) 2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i 2004-2011 E63 E64 BMW 645ci 650i 1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe 2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si 2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is 2000-2003 E52 BMW Z8 Roadster (without EDC)
Show More Show Less
