Packaged by Turner for BMW 3 Series E36 (1992-1998)

Automatic transmissions are reliable, shift smoothly, and can last without issue so long as they are properly maintained. Over time, the transmission fluid becomes thick and the filter becomes contaminated with small metal particles. This can cause excess wear, high transmission operating temperatures, and eventual failure. To prevent this we recommend changing your filter, fluid, and seals to ensure your transmission continues to operate flawlessly. We recommend filter and fluid changes every 50,000 miles. This kit includes Pentosin ATF-1, the transmission filter, gasket and bolts. 

Kit Includes:

• Automatic transmission filter with associated hardware
• Oil pan gasket
• Drain plug with sealing washer
• Fill plug with sealing washer
• 5 liters Pentosin ATF-1 automatic transmission fluid

This item fits the following BMWs: 
1995-1999  E36 BMW M3 
1991-1995  E34 BMW  530i

This kit is contains all new strut and shock mounts and hardware needed when installing a new shocks and struts or aftermarket suspension on your vehicle. 

Fits the following BMW's

E36 318i/ic/is 323i/ic/is 325i/is/ic 328i/is/ic 

Tired of dealing with excess shifter slop and a mushy shifter? The Turner Shifter Rebuild & Upgrade Kits will restore your shifter's crisp feel and eliminate excessive movement that develops over time with wear. Included in this kit are all the common wear components and OE quality bushings that will give you a tighter shifting feel and will hold up like a day 1 BMW.

This kit is perfect to restore your driving pleasure!

See the included components under Kit Contents below.

When replacing your worn out brakes, the market is flooded with performance options. If your BMW doesn't see track time, it's not very practical. Performance pads and rotors tend to result in a lack of bite at low braking temperatures and cause excessive noise in daily driven vehicles that becomes irritating. BMW brakes from the factory are perfectly suited for trips around town, across the country, and even the occasional spirited driving session, delivering smooth, quiet, and long lasting performance. 

Included in this E36 BMW brake package are all of the OEM equivalent components needed to replace your Front & Rear brakes with comfort, reliability, and optimal lifespan in mind.

Brake components in this kit:

• Textar Front & Rear Brake Pads
• Zimmerman Front & Rear Rotors
• New Front & Rear Wear Sensors
• Brand New Stainless Steel Set Screws
• Syl-Glide Silicone Brake Lubricant 

Fits the following BMWs:
E36 BMW 318i/is/ic 323is 325i/is/ic 328i/is

Regular maintenance is key to keeping your BMW running smoothly, and the water pump is a critical component that should be serviced every 60,000 miles. To ensure the overall efficiency of your cooling system, it's also recommended to replace the thermostat at the same time. Turner Motorsport has created a streamlined solution with their Water Pump & Thermostat Replacement Kit, making your cooling system upgrade simple and effective.

Kit Includes:

Meyle Water Pump with Metal Impeller (11510393338) VEMO Thermostat - 88°C (11537511580) Elring Thermostat Housing Flange Gasket (11531721172) Genuine BMW Coolant/Antifreeze (82141467704) Benefits:

Enhanced Cooling Efficiency: Earlier opening thermostat improves temperature control under performance conditions. Reliable Components: Includes high-quality parts from Meyle and VEMO, known for their durability and reliability. Complete Solution: All necessary components for a comprehensive cooling system refresh in one convenient kit. Performance-Driven Design: Ideal for those looking to maintain and enhance the cooling capabilities of their S55 engine.

Just like the rest of your vehicle's major systems, the cooling system must also be addressed periodically to ensure proper cooling and component reliability. Plastic and rubber components become brittle and prone to splitting or cracking after long periods of heating and cooling cycles, especially in colder climates! The coolant itself can degrade or become contaminated, leading to potential corrosion or freezing issues. Finally, thermostats and sensors can fail completely, preventing proper cooling and/or coolant temperature readings to become inaccurate.

To make sure you are not left stranded on the side of the road with an overheated engine, we have put together this Basic Cooling System Service kit. This kit contains all of the most-likely-to-fail components, giving you peace of mind knowing your engine will continue to run cool for another 60,000+ miles.

See kit contents below for all included components.

This strut and shock mount package covers the front and rear rubber mounts and bushings commonly replaced during a strut and shock install. While you're installing new front struts and rear shocks these are easily installed - there's no additional labor and special tools are not required. Since these pieces are mostly rubber, they dry up and crack over time. Re-using them lead to problems with fitment or noise, and may have safety issues as well. These mounts and pads are the perfect complement to your new shocks to help restore your car's handling and performance.

We sell the basic strut and shock mount package, which includes:

• Front strut mounts (also known as guide support)
• Front strut reinforcement plates (to prevent cracking and deforming of the front strut towers)
• Front strut tower paper washer gaskets
• Front and rear self-locking mounting nuts
• Rear Lifetime Warranty 'Repair Shop' shock mounts
• Rear shock mount reinforcements (to prevent cracking of shock towers)
• Rear shock mount gaskets

In addition, you can add the front spring pads, front bump stops, front dust boots, rear bump stops, and rear dust boots if needed. But please note that some shocks and coil overs come with all or some of these pieces already. If in doubt, check with your supplier on what is included.

We offer three varieties of the rear shock mounts - OEM, Repair Shop, and HP alum-rubber. We recommend either the Repair Shop or HP mounts because the stock OEM design has a flaw that can lead to premature failure of the mounts. The Repair Shop and HP mounts use a different design that will last longer and the Repair Shop mounts also have a lifetime warranty!

This item fits the following BMWs:
1996-1999 E36 BMW M3
1996-2002 Z3 BMW 2.5 2.5i 2.8 3.0i M Coupe

This kit is contains all new strut and shock mounts and hardware needed when installing a aftermarket suspension on your vehicle. 

Fits the following BMW's

1995 BMW E36 M3 S50 

Whether you are looking to replace your E36 M3's worn out stock components or simply upgrade your existing braking system for a more aggressive and responsive feel, this kit has been hand pick by us to suit your needs. Featuring Hawk HPS 5.0 performance brake pads for increased bite and better heat resistance, these pads offer significantly improved braking power and less dust, compared to the stock brake pads, without compromising the ABS system and without the harshness typically associated with performance style pads.

Kit Components:

• Front and Rear Pagid Premium Coated Rotors
• Front and Rear Hawk HPS 5.0 Street Sport Brake Pads
• Front and Rear Brake Rotor Set Screws
• TYP 200 Brake Fluid - 1 Liter
• Front and Rear Brake Sensors
• ATE Plastilube Anti-Squeal Compound

In some cases, we offer performance alternatives to the OEM items. For an enthusiastic BMW owner, the standard BMW part may be inadequate and we offer an upgraded part, based on our 20 years of BMW tuning experience. We seek out high-quality suppliers and designs that we would want on our own vehicles. Many times performance parts will fix a design flaw with the original BMW part, improving your performance at the same time. 

This kit fits the following BMWs:
1995-1999 E36 BMW M3

When it comes time to replace your thermostat, be sure you have everything you need. This kit includes everything you need to replace your thermostat, including the thermostat.

Kit includes:

• Thermostat with gasket
• Thermostat mounting hardware
• 1 liter of coolant

This waterpump fits the following BMWs: 
1992-1999 E36 3 series - 323is, 323ic, 325i, 325is, 325ic, 328i, 328ic, M3 3.0 (S50/US), M3 3.2 (S52) 

The fan that attaches to the water pump carries so much rotational mass that it can actually hinder the performance of your engine. To address this, we now offer out line of fan delete kits that replace everything needed to get rid of your fan and fan clutch, without causing cooling issues as a result. This Ultimate kit is the top tier option, including the essential conversion components, the upgraded aluminum thermostat housing, and a brand new accessory belt.

This kit is best for someone who has not performed recent cooling system maintenance or who wants to replace everything at once for increased reliability and longevity.

Included in this kit:

• 80* thermostat
• 1 liter of coolant
• Water Wetter coolant additive
• Low-temperature coolant temperature sensor/switch
• Aluminum thermostat housing with gaskets
• Fan delete nut
• ECS  Aluminum Water Pump Pulley - Black
• Accessory Belt

Fits the following BMWs:
1992-09/1995 E36 BMW 325i/is/ic 328i/is/ic M3

**This kit is intended to be used with cars that have a functional auxiliary fan (64508364093) or an upgraded electrical fan installed.**