BMW Engine Parts for BMW E60 M5 S85 5.0L

The oxygen sensor is vital to the performance and drivability of your car. The engine computer relies on data from the sensor to make adjustments in engine efficiency and performance. When your BMW oxygen sensor fails, the computer can no longer sense the air/fuel ratio, so it ends up guessing -- resulting in poor performance, poor gas mileage, and increased pollution. Make sure your BMW engine performs as it should, and doesn't use more fuel than it needs to, by simply changing your oxygen sensor today. There is no lifespan on O2 sensors but there are several fault codes that indicate a failed sensor (O2 monitoring, cat efficiency, O2 heating circuit, O2 readiness, and others). The O2 sensor is heated and has a self-calibration feature so once you get the codes or feel performance has suffered, a new sensor is a good starting point to get you back to peak performance.

This is a Bosch O2 sensor - also known as a Lambda probe. Bosch is an OEM supplier to BMW.

Position: bank 1, before the catalytic converter (pre-cat).

This item fits the following BMWs:
2006-2010 E60 BMW M5
2006-2010 E63 E64 BMW M6

Has the idle gone crazy on your S85 V10 engine? This is the Genuine BMW idle control device for cars with the S85 V10 engine. The fuel injection idle control valves are sold individually.
When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

2006-2010 E60 BMW M5
2006-2010 E63 BMW M6

BMW E60 M5 Crank Case Test Cap

The BMW E60 M5 Crank Case Test Cap is designed to facilitate accurate testing of crankcase pressure across a range of vehicle models. This versatile test cap is compatible with early and late model vehicles equipped with steel, aluminum, or plastic valve covers. Featuring a multi-diameter fitting, it connects directly to IMIBs, handheld manometers, and smoke machines, eliminating the need for adapters and ensuring precise readings without leaks.

Benefits:

• Versatile Compatibility: Suitable for use with steel, aluminum, and plastic valve covers on early and late model vehicles.
• Direct Connection: Multi-diameter fitting allows direct connection to IMIBs, handheld manometers, and smoke machines.
• Leak Prevention: Eliminates the need for adapters, reducing the risk of leaks and inaccurate readings.
• Enhanced Accuracy: Provides reliable crankcase pressure testing for better diagnostic results.

Rod bearings should be replaced as a preventative measure before 80,000 miles. This package is the most complete rod bearing overhaul kit available and includes not just the latest BMW rod bearings and connecting rod bolts, but also everything else that should be replaced with the oil pan and front subframe off the car.

Rod bearings continue to be a sore subject among M3, M5, and M6 owners. The rod bearings in the S85 V10 have been known to fail within 60,000 miles. There could be a number of reasons for premature failure with a lot of finger-pointing as to the real cause. Whatever the reason, rod bearings are wearing out sooner than expected and their replacement should be considered a required preventative maintenance item. We suggest a replacement interval of between 60,000-80,000 miles with frequent engine oil analysis done along the way*. Driving moderately and allowing the engine to warm up before hard use will also extend rod bearing life.

After doing so many rod bearing replacements in our own service shop we have put together this comprehensive overhaul package. Our package includes -

Genuine BMW rod bearings
- 11247841703, upper bearings - latest design from BMW (either original or WPC treated**)
- 11247841702, upper bearings - latest design from BMW (either original or WPC treated**)
- 11247834522, connecting rod bolts
- Red Line engine assembly lube

Oil Pan
- 11137836361, oil pan gasket
- 07119905485, oil pan screws (required by BMW)
- 07129905600, oil pan screws (required by BMW)
- 11137836568, oil pan screws
- 07119963129, seal washers
- 11417836233, auxiliary oil pump gaskets
- 11121304174, oil pickup tube o-ring

Replacing the rod bearings requires mechanical knowledge and skill, a clean workspace, and several specialist tools. Our preferred procedure is to leave the engine in the car but remove the front subframe. The engine must be supported from above with an engine brace. Removing the front subframe involves disconnecting the control arms and steering rack and steering column. The oil pan can then be removed and you can access the connecting rods and bearings. Replacing the rod bearings themselves is straightforward but patience and forethought will be extremely helpful. In addition to analyzing the severity of the rod bearing wear, the crankshaft must also be inspected closely for damage. Rod bearings that have been severely worn may have damaged the crankshaft (requiring replacement or machining).

* BMW released an updated rod bearing around 2011 that uses different materials than the original design. The old rod bearings were constructed with several layers or metal, including copper and lead. If an engine oil analysis revealed high levels of these specific metals then it was a sure sign that the rod bearings were nearing replacement. However, the new BMW bearings do not use copper or lead so an oil analysis will not alert you to heavy bearing wear. The new bearings are also a harder material which prolonged the life of the bearing but increased the liklihood of crankshaft damage if a bearing failed. Even though the bearing theoretically lasts longer it's even more important to preventativly replace them before they damage the crankshaft.

** These WPC-treated bearings are the best we have seen for the S85. WPC is a shot-peening treatment at a microscopic level. It's perfect for sensitive surfaces like bearings. The WPC treatment removes imperfections and high spots, while creating a surface that retains oil better than the original surface. This greatly reduces friction. The bearings in this kit are factory BMW bearings that are sent to WPC for treatment. The treated bearings are stronger with less metal fatigue and less friction than buying off-the-shelf bearings from the dealer.

***BE Bearings is another top pick when considering which bearing kit to choose. Working with Clevite, an OE bearing supplier, their design allows for a bit more clearance than stock, allowing better oil circulation and reducing friction. The material is also made from the original bearing composition of lead-copper, not the updated tin-aluminum used in factory BMW bearings which was excessively hard, potentially damaging the crankshaft when high friction occurred. This softer metal composition can also be tested for via oil analysis, allowing you to see high bearing wear, something the tin-aluminum bearings don't give you the ability to do.

Internal VANOS Pressure Line
One of the VANOS oil lines runs along the inside of the timing chain cover and into the oil pan. It can only be replaced with the oil pan removed. If you have sluggish performance or VANOS fault codes this is one of the common causes and now is the perfect time to replace it. If it fails down the line the oil pan will have to be removed again.

Front Subframe Hardware
Our preferred procedure for accessing the engine block is by disconnecting the control arms and steering rack and then removing the front subframe altogether. This hardware is not required but may be a good idea, especially if your original subframe bolts are rusty. Hardware includes:
31106760222, front subframe mounting bolts
31106770256, front subframe mounting bolts
33326760668, front wishbone collar nut

Tie Rod Boots
32106765782, tie rod boot kit

Motor Mounts with Hardware
22116762607, left motor mount
22116762608, right motor mount
07129904088, motor mount bolts
07129904865, motor mount nuts

Engine Oil Change
Liqui Moly GT1 10w-60 engine oil
11427840594, OEM oil filter.

This package fits the following BMWs:
2006-2010 E60 BMW M5
2006-2011 E63 BMW M6

The GENIUS10 is a powerhouse among our chargers known for its exceptional performance, energy efficiency, and compact design. The GENIUS10 is a versatile 6-volt and 12-volt charger, maintainer, and desulfator with a robust 10-amp rating. It's engineered to handle lead-acid batteries used in automotive, marine, and deep-cycle applications, covering flooded, gel, AGM, maintenance-free types, as well as lithium-ion batteries.

Features:

• Do more with Genius - Designed for 6-volt and 12-volt lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion batteries.
• Enjoy precision charging - An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates.
• Charge dead batteries - Charges dead batteries as low as 1-volt. Or use the all-new Force Mode that allows you to take control and manually begin charging dead batteries down to zero volts.
• Simple to set up and use - Plug-in, connect to the battery, select a charge mode, and start charging your battery. A fully-automatic, worry-free battery charger for year-round use.
• Restore your battery - Detects sulfation and acid stratification and restores lost performance for stronger engine starts and extended battery life.
• Compatible with all types of vehicles - Charge and maintain cars, motorcycles, lawnmowers, ATVs, tractors, trucks, SUVs, boats, classic cars, hot rods, and more - you name it.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.