BMW Electrical Sensors, Switches, & Relays for BMW 5 Series E60 (2004-2010)

The eccentric shaft sensor plays a vital role in controlling valvetronic timing and is often a common issue in BMW vehicles. If you've noticed difficult starts, reduced fuel economy, and overall engine power and performance issues, this component could be the culprit.

Key Features:

Guaranteed Fitment: Designed to fit perfectly, ensuring compatibility with your vehicle. Accurate Positioning: Provides precise shaft position control, even at high RPMs. Direct OE Replacement: Easy to install with its direct-fit design, saving time and effort. Low Electrical Resistance: Alloy connector conductors minimize resistance, ensuring accurate signal transmission. Upgrade to this quality replacement eccentric shaft sensor to restore optimal engine performance and address the symptoms associated with a faulty sensor.

This is a high quality replacement OEM VDO Mass Air Sensor.The MAF controls the amount of fuel that goes through the injectors based on the volume of air coming through the intake. If your vehicle is giving you a MAF code, replace it immediately to ensure you get the best gas mileage and performance. It is common for this part to fail slowly and cause poor fuel mileage and hampered performance. When it fails completely, the vehicle will stutter and stall as it falls into a limp mode. One way to check if your MAF is bad is to unplug the connector before starting your car. If it idles well (compared to a previous poor idle), your MAF needs replaced. If you let this maintenance part go, your fuel economy will suffer as too much fuel is going into the engine and not being burned. A great way to give your vehicle an efficiency boost.

OEM replacement for BMW part # 13627551638.

OEM VDO is one of the largest OE providers in the world, supplying numerous vehicle brands, including BMW, with many of their genuine parts that build the vehicle before they ever reach the car lot. Entrusted by many of the top names in automotives and with their proven history of reliability, it makes all of us here at Turner confident that their line of OEM replacement parts are a perfect option to restore your vehicles original operation and performance. The same great quality or higher than Genuine BMW parts at a lower cost.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Ensure your BMW's oil level is accurately monitored with the Bremmen Parts oil level sensor. If your car displays a yellow oil light upon startup, it's a sign of a failing sensor affecting oil level readings. Simple to replace, this sensor is located at the oil pan's bottom. Follow straightforward steps: drain the oil, replace the sensor, clean the area, and install the new sensor. The kit includes a new sealing O-ring for a leak-free installation, ensuring your engine's proper oil level monitoring.

Key Benefits:

• Addresses yellow oil light indicating sensor failure
• Easy replacement process located at the oil pan's bottom
• Includes sealing O-ring for leak-free installation

The alternator in your vehicle keeps the battery at full charge when your engine is running. Because all of your electronic systems run off of this small piece, it's important that it is operational. If your lights are dim while driving or your battery dies within minutes of starting your car, it's time for a new alternator.

This is a NEW alternator from the OEM manufacturer, Valeo. No core charge applies. Valeo is an OEM manufacturer for many BMW alternators - save money by buying the same alternator in a different box!

For vehicles with production date from 03/2005.

Includes connector housing with terminals and seals. Commonly used for the engine oil pressure switch.

ECS Tuning replacement harness connectors include all necessary pins and wire seals for a complete harness repair. Whether you have a broken harness connector or need a complete wiring repair, we have the components you need.

Each connector includes an additional terminal in case one becomes lost or damaged during installation.

Suggested tools:

Suggested crimping pliers: T#387193
Wire De-pin tools:
12pc De-Pin Tool Set - T#386379
23pc De-Pin Tool Set - T#641943