BMW Engine Parts for BMW 5 Series E60 (2004-2010)

Upgrade your BMW's engine bay with the Aluminum Valve Cover 11127552281M to eliminate leaks and add a touch of style. This high-quality valve cover ensures a secure seal, preventing leaks and enhancing the aesthetic appeal of your BMW.

• Aluminum Valve Cover for BMW
• Eliminates leaks for improved engine performance
• Adds style to the engine bay
• High-quality construction for durability and reliability

Upgrade your stock oil cooler thermostat for improved performance. Swap your factory 110-degree Celsius thermostat for a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly, unlike thermostat bypass kits.

Kit contents:​

Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Upgrade your stock oil cooler thermostat for improved performance. Swap out your existing cover with ease, replacing it with a durable billet cover. Upgrade from your 110-degree Celsius thermostat to a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly unlike thermostat bypass kits.

Kit contents:

Billet thermostat housing cover
Replacement gasket
Hardware
Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Perfect for DIY enthusiasts, this all-in-one kit has everything you need to refresh your ignition system! With just one click, you'll get high-quality, matching replacement parts, making it simpler than ever to service and restore your ignition system.

If you're noticing misfires, poor fuel economy, reduced engine performance, or ignition-related diagnostic trouble codes (DTCs), a failing ignition coil is likely the cause. Late-model BMWs, such as the E60 M5, E63 M6, and E64 M6, use a coil-on-plug ignition system, where each cylinder has its own coil and spark plug for efficient ignition. When a coil fails, the affected cylinder won't receive a spark and will misfire. Even if the misfire doesn’t trigger a DTC, you’ll still feel the difference in engine performance—rough idling, hesitation during acceleration, or a strong fuel smell. To avoid these issues, we recommend replacing your ignition coils every 40,000-60,000 miles.

The S85's MSS65 DME uses a unique ignition system known as Ionic Current Control. BMW engineers developed this system to more accurately detect pre-ignition and misfires in the high-revving, ten-cylinder S85. Instead of relying on conventional knock sensors, the system uses each spark plug as a current probe, applying a low voltage to the electrode immediately after the power stroke and sending the resulting current to the Ionic Current Control Unit (ISS) for evaluation. This allows for precise monitoring of combustion events. To support this, the S85’s ignition coils are specially designed with a modified “pencil” shape and lack the typical Zener diode in the secondary winding, allowing for accurate current measurements without triggering fault codes in the engine control unit (DME). Bavarian Autosport ignition coils are manufactured to the exact specifications of the OE Ionic Current Control-compatible ignition coils, and will not trigger ignition-related fault codes in the DME.

Bavarian Autosport ignition coils are engineered for reliability, delivering a consistent, long-lasting spark. These high-quality OE replacement coils are specifically designed for your S85-powered E60 M5, E63 M6, or E64 M6. Constructed with durable, heat-resistant plastic and featuring premium rubber spark plug boots, each boot is pre-lubricated with dielectric grease to ensure smooth installation and prevent corrosion.

Features & Benefits:

Bavarian Autosport Ignition Coils - Set of Ten Durable, temperature-resistant plastic construction is designed to withstand extreme heat and harsh conditions, ensuring long-lasting performance. High-quality rubber spark plug boots are pre-lubricated with dielectric grease to prevent moisture intrusion and potential corrosion. Built to meet or exceed OE manufacturing standards, guaranteeing a perfect fit, reliable performance, and seamless installation. NGK 4471 LKR8AP Spark Plugs - Set of Ten Multi-ground electrodes improve ignition capability and are less sensitive to increased voltage use with gap growth. Corrugated ribs prevent flashover. Copper core aids in heat removal. Pre-gapped to 0.035" (0.9mm) OEM-specified spark plug for all S85 applications.

Ensure proper sealing when installing the turbos on your N54.

Kit includes:

• 16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

BMW N52 3.0L, N55 3.0L Timing Chain Tensioner With Guard Rail

Ensure proper engine performance and prevent catastrophic damage with the BMW N52 3.0L, N55 3.0L Timing Chain Tensioner With Guard Rail. This essential component maintains tension on the timing chain, preventing slack that can lead to skipped teeth and engine failure.

Benefits:

• Maintains proper tension on the timing chain
• Prevents skipped teeth and potential engine damage
• Includes guard rail for added protection
• Quiets noisy timing chains

Keep your BMW engine running smoothly and reliably with the BMW N52 3.0L, N55 3.0L Timing Chain Tensioner With Guard Rail.

The S85 engine has a known history of rod bearing failure. If your engine is higher mileage, don't let this catastrophic failure happen to you. Replace your rod bearings and prevent a spun bearing, a failure that has the potential to trash your crankshaft.

What is WPC, you ask? WPC is a surface treatment that reduces friction and adds strength - two improvements that benefit internal engine components. Ultra-fine particles are fired at the surface at very high speeds, like shot-peening - but much, much smaller. The parts come out smoother and stronger due to thermal discharge. The two largest enemies of any high-performance engine are heat and friction - and WPC has found a way to reduce both. What are you waiting for? Use WPC-treated bearings on your next engine build or rod bearing service!

Kit Includes:

Turner Motorsport "Race Series" WPC-Treated Rod Bearing Shells (20) Genuine BMW Connecting Rod Bolts (20) OEM MANN Oil Filter Kit Castrol Edge Euro Car Engine Oil (10w-60) - 9 Quarts Genuine BMW Oil Drain Plug Turner Oil Change Decal Elring Oil Pan Gasket Permatex Ultra Slick Engine Assembly Lube (4 oz.)

Often an oversight in maintenance, ignition components are also susceptible to wear and tear. Spark Plugs can accumulate carbon, reducing the spark intensity and it's ability to properly ignite the air/fuel mixture, leading to misfires and generally declining performance. Other ignition components, such as coils, boots, wires, caps, and rotors, can also wear out over time due to factors like heat and contamination, preventing the current from reaching the spark plug.

To start over fresh with all new components, we now offer these Ignition Service Kits. Each kit comes with brand new OE quality components, replacing any potential fault points in your ignition system for peak performance!

See kit contents below for a complete list of included components.