BMW Engine Parts for BMW 5 Series E60 (2004-2010)

For BMW M54 applications, coil styles vary between M or N depending on the vehicle's production date. Models produced up to September 2002 require the M series style coil, while those manufactured after September 2002 use N series style coils. It's crucial to visually compare and verify the correct coil needed for your vehicle before making a purchase.

Benefits:

• Specific coil styles for different BMW M54 application dates
• Helps ensure the right replacement part for your vehicle's coil
• Visual verification recommended prior to purchase for compatibility

Upgrade your stock oil cooler thermostat for improved performance. Swap your factory 110-degree Celsius thermostat for a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly, unlike thermostat bypass kits.

Kit contents:​

Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

This is an OEM INA mechanical tensioner for the serpentine belts on BMW's with the N54 engine. This tensioner keeps the belt for the alternator, power steering and Air Conditioning taught to provide maximum performance of each system.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2008-2010 E82 BMW 135i
2011 E82 BMW 1M Coupe
2006-2010 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-2013 E92 BMW 335i 335is 335xi 335i xDrive - Coupe
2007-2013 E93 BMW 335i 335is - Convertible
2004-2010 E60 BMW 535i 535xi 535i xDrive

This is an OEM INA mechanical tensioner for the serpentine belt. This tensioner keeps the belt for the alternator, power steering and Air Conditioning taught to provide maximum performance of each system.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Upgrade your stock oil cooler thermostat for improved performance. Swap out your existing cover with ease, replacing it with a durable billet cover. Upgrade from your 110-degree Celsius thermostat to a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly unlike thermostat bypass kits.

Kit contents:

Billet thermostat housing cover
Replacement gasket
Hardware
Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

This is an OEM INA Upper Idler Pulley, also known as the roller pulley or deflection pulley. The idler pulleys are known to be the primary sources for 'belt squealing'. The pulley is also encased in rubber which will crack over time. If left without service the rubber could fail completely, chucking the belt and leaving you stranded. Replacement is a very simple procedure and can be done anytime the fan is off the engine (belt replacement, water pump service, alternator replacement, etc).

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2008-2010 E82 BMW 135i
2011 E82 BMW 1M Coupe
2006-2010 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-2010 E92 BMW 335i 335is 335xi 335i xDrive - Coupe
2007-2010 E93 BMW 335i 335is - Convertible
2004-2010 E60 BMW 535i 535xi 535i xDrive

• 11127582245 - N52 valve cover gasket set
• 11127552280 - N52 eccentric shaft sensor seal
• 11127559699 - N52 Valvetronic gasket

Ensure proper sealing when installing the turbos on your N54.

Kit includes:

• 16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

This is an OEM INA Idler Pulley, also known as the roller pulley or deflection pulley. The idler pulleys are known to be the primary sources for 'belt squealing'. The pulley is also encased in rubber which will crack over time. If left without service the rubber could fail completely, chucking the belt and leaving you stranded. Replacement is a very simple procedure and can be done anytime the fan is off the engine (belt replacement, water pump service, alternator replacement, etc).

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2008-2010 E82 BMW 135i
2011 E82 BMW 1M Coupe
2006-2010 E90 BMW335i 335xi 335i xDrive - Sedan
2007-2010 E92 BMW 335i 335is 335xi 335i xDrive - Coupe
2007-2010 E93 BMW 335i 335is - Convertible
2004-2010 E60 BMW 535i 535xi 535i xDrive

The S85 engine has a known history of rod bearing failure. If your engine is higher mileage, don't let this catastrophic failure happen to you. Replace your rod bearings and prevent a spun bearing, a failure that has the potential to trash your crankshaft.

What is WPC, you ask? WPC is a surface treatment that reduces friction and adds strength - two improvements that benefit internal engine components. Ultra-fine particles are fired at the surface at very high speeds, like shot-peening - but much, much smaller. The parts come out smoother and stronger due to thermal discharge. The two largest enemies of any high-performance engine are heat and friction - and WPC has found a way to reduce both. What are you waiting for? Use WPC-treated bearings on your next engine build or rod bearing service!

Kit Includes:

Turner Motorsport "Race Series" WPC-Treated Rod Bearing Shells (20) Genuine BMW Connecting Rod Bolts (20) OEM MANN Oil Filter Kit Castrol Edge Euro Car Engine Oil (10w-60) - 9 Quarts Genuine BMW Oil Drain Plug Turner Oil Change Decal Elring Oil Pan Gasket Permatex Ultra Slick Engine Assembly Lube (4 oz.)

Often an oversight in maintenance, ignition components are also susceptible to wear and tear. Spark Plugs can accumulate carbon, reducing the spark intensity and it's ability to properly ignite the air/fuel mixture, leading to misfires and generally declining performance. Other ignition components, such as coils, boots, wires, caps, and rotors, can also wear out over time due to factors like heat and contamination, preventing the current from reaching the spark plug.

To start over fresh with all new components, we now offer these Ignition Service Kits. Each kit comes with brand new OE quality components, replacing any potential fault points in your ignition system for peak performance!

See kit contents below for a complete list of included components.