BMW Engine Parts for BMW 5 Series E60 (2004-2010)

A cracked valve cover can cause a myriad of problems none of which are inexpensive. A simple oil leak may prove nothing more than a driveway nuisance; however, the damage that can occur as a result of low oil do more to drain the wallet. A small vacuum leak may cause only a minor hesitation but the reduced efficiency means less mpg's and more trips to the pump. This factory replacement valve cover will get you back on the road and ensure a solid and tight seal along the top end of the engine. 
When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Cylinder Head Cover -
This item fits the following BMW Chassis:
E71,E82,E90,E92,E93,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4,F30,F32,F33,F34,F36

Fits BMW Engines including:
N55
 

Ensure proper sealing when installing the turbos on your N54.

Kit includes:

• 16 - ASA M7x39 studs
• 16 - Flange nuts
• All required gaskets and o-rings
• Water pump install hardware
• Replacement vacuum hose
• T-bolt clamps

Helpful hints:

For complete installation instructions, refer to Haynes Service Manual (T#193950).

Both downpipes must be removed to remove either front or rear turbo. Tie rod end may need to be separated from knuckle for clearance. Steering rack may also need to be rotated away from subframe for access. Valve cover heat shield will need to loosened and pushed upward to get clearance for turbo manifold removal.

If studs back out of cylinder head and nuts are seized to studs, replace studs. Thread studs in to head by hand to prevent cross threading. When installing the new studs in the cylinder head, use a high temperature loctite in the cylinder head side, and copper anti-seize on the nut side.

To make more room for access to the front turbo, remove the rubber line running in front of the subframe that attaches to the back of the map thermostat and remove the clip. Cut off the OEM clamp and replace it with a new hose clamp as well.

Complete removal of the water pump is not required. Detach the water pump from the side of the block and push it out of the way to make more room for access to the front turbo. If water pump is unbolted from the block, the aluminum bolts must be replaced.

Torque specs:
Bracket to cylinder head: 9Nm
Coolant supply line to crankcase: 9Nm
Coolant return line to crankcase: 8Nm
Coolant return line to turbo: 8Nm
Coolant supply line to supply line: 8Nm
Exhaust manifold heat shield: 8Nm
Oil supply line to crankcase: 20Nm
Oil pressure line to turbo: 8Nm
Oil return line to crankcase: 8Nm
Oil return line to turbo: 8Nm
Turbo manifold to head: 20Nm

This is an OEM INA Idler Pulley, also known as the roller pulley or deflection pulley. The idler pulleys are known to be the primary sources for 'belt squealing'. The pulley is also encased in rubber which will crack over time. If left without service the rubber could fail completely, chucking the belt and leaving you stranded. Replacement is a very simple procedure and can be done anytime the fan is off the engine (belt replacement, water pump service, alternator replacement, etc).

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2008-2010 E82 BMW 135i
2011 E82 BMW 1M Coupe
2006-2010 E90 BMW335i 335xi 335i xDrive - Sedan
2007-2010 E92 BMW 335i 335is 335xi 335i xDrive - Coupe
2007-2010 E93 BMW 335i 335is - Convertible
2004-2010 E60 BMW 535i 535xi 535i xDrive

BMW N52 3.0L, N55 3.0L Timing Chain Tensioner With Guard Rail

Ensure proper engine performance and prevent catastrophic damage with the BMW N52 3.0L, N55 3.0L Timing Chain Tensioner With Guard Rail. This essential component maintains tension on the timing chain, preventing slack that can lead to skipped teeth and engine failure.

Benefits:

• Maintains proper tension on the timing chain
• Prevents skipped teeth and potential engine damage
• Includes guard rail for added protection
• Quiets noisy timing chains

Keep your BMW engine running smoothly and reliably with the BMW N52 3.0L, N55 3.0L Timing Chain Tensioner With Guard Rail.

The URO Valvetronic Actuator is a high-quality replacement part for BMW engines, designed to restore precise control over valve timing and lift, enhancing engine performance, fuel efficiency, and responsiveness. Built to meet strict OEM standards, this actuator helps optimize the power and efficiency of BMW engines, making it an ideal solution for maintenance or repair. Available from Turner Motorsport, the URO Valvetronic Actuator ensures a reliable fit and excellent performance for BMW owners.

• Restores optimal control over valve timing for enhanced engine efficiency
• Improves throttle response and provides smoother acceleration
• Contributes to lower emissions and better fuel economy
• High-quality construction built for long-lasting durability
• Direct-fit replacement compatible with select BMW models
• Available from Turner Motorsport, a trusted source for BMW parts

The URO Valvetronic Actuator is a cost-effective replacement that delivers the reliable, high-performance operation BMW owners expect.

Features & Benefits:

Two configurable linear 0-5V analog outputs Ability to calibrate O2 sensors for maximum accuracy Includes LC-2 controller and Bosch wideband O2 sensor Comes with a program cable, manual, and a 10 ft. sensor cable Includes a 1-inch mild steel exhaust bung Innovate MTS serial in/out capability Integrated dual-color status LED (green/red) Patented DirectDigital™ wideband sensor control Positive lock connectors for all connections Real-time display data on screen or with the powerful LogWorks software Range:

AFR (Air-Fuel Ratio) range from 7.4:1 to 22.4:1 (0.5 to 1.5 lambda)