A bad DISA valve can cause a variety of issues, from a loud racket in the engine bay, hesitation at low rpm and a rough idle with lean codes.

If the valve is making a loud noise, we recommend replacing it as soon as possible. It is possible for the pin holding the flap to be sucked into the motor causing serious damage.

Very easy to replace, just need to undo the 4 bolts holding it to the intake manifold.

Turbosmart GenV Raceport BOV (Fits competitors 50mm / female style flange. No weld flange included)

The Race Port is renowned for its exceptional compactness and lightweight design tailored for turbocharged competition-level engines. With its innovative collar design and internal flow structures, this BOV stands out as 50% lighter and 25% smaller than competing models, yet it boasts an impressive flow rate of 330 CFM, making it the market's top-performing BOV in its category.

Fits Chargepipes With Tial/Turbosmart Flange

Turbosmart GenV Raceport BOV (Fits competitors 50mm / female style flange. No weld flange included)

The Race Port is renowned for its exceptional compactness and lightweight design tailored for turbocharged competition-level engines. With its innovative collar design and internal flow structures, this BOV stands out as 50% lighter and 25% smaller than competing models, yet it boasts an impressive flow rate of 330 CFM, making it the market's top-performing BOV in its category.

Fits Chargepipes With Tial/Turbosmart Flange

Maximum Flow Pro5R Filter

This intake kit replaces your restrictive factory air box. It features a 1.6mm powder-coated steel heat shield, heat-resistant molded intake tube, trim sealed to seal out hot engine air, and a custom application-specific aFe brand cotton filter.

This version uses aFe's highest flowing filter media, which uses a lightly oil gauze to filter out dirt and particulates, while allowing more air to flow to the intake. For the best flowing filter, with the best performance gain, we always recommend this standard aFe filter media (often called "Pro5R ", which has a blue pre-oiled filter media). We also carry this filter in the "ProDry" grey filter media, which is oil-free for only slightly less performance and no maintenance.

By removing your stock intake air box, you are removing the most restrictive portion of your intake system, increasing both horsepower and torque, improving acceleration as well as throttle response.

This part fits the following BMWs:
2003 - 2006 E60 Sedan 525i 530i 

Maxiumum Flow Pro5R Filter

11.75 hp and 10.50 lb/ft torque gain!

This intake kit replaces your restrictive factory air box. It features a 3-angle velocity stack adapter, heat-block molded intake tube, 1.6mm powder-coated steel heat shield, trim sealed to seal out hot engine air, and a custom aFe brand cotton filter.

This version uses aFe's highest flowing filter media, which uses a light oil gauze to filter out dirt and particulates while allowing more air to flow to the intake. For the best flowing filter, with the best performance gain, we always recommend this standard aFe filter media (often called "Pro5R ", which has a blue pre-oiled filter media). We also carry this filter in the "ProDry" grey filter media, which is oil-free for only slightly less performance and no maintenance.

By removing your stock intake air box, you are removing the most restrictive portion of your V8's intake system, increasing both horsepower and torque, improving acceleration as well as throttle response.

11.75 hp gain at 5900 rpm
10.50 lb/ft torque at 4000rpm

Clickhere for installation instructions.

This part fits the following BMWs:
2003 - 2010 E60 Sedan 550i 
2004 - 2010 E63 6 Series Coupe 650i 

In addition to the weak stock chargepipe, the factory N54 diverter valves can also be a source for boost leaks. The diverter valve takes overboost and re-directs it back through the intake and turbos instead of allowing it to pass into the intake manifold. It's the same as a blow off valve (BOV) but instead of releasing into the engine bay, it stays contained to the engine. The stock diverter valves (DV) are plastic and connect with more plastic into the chargepipe and turbo inlet pipes. The plastic can become brittle and crack even on stock engines and leak boost, which leads to a loss in power and performance.

Turbosmart has developed two kits to replace and upgrade the stock diverter valves - a direct replacement kit (shown) and a combination DV/BOV "Dual Port" kit. This direct replacement kit includes new high-performance DV and stronger silicone hose to connect them to the turbo inlet pipes (Vargas silicone inlets are recommended). The Turbosmart Kompact DV will give you all of the strength and reliability you need to take your turbo build to the next level.

You will also need T#553932