Packaged by Turner for BMW 5 Series E60 (2004-2010)

Just like the rest of your vehicle's major systems, the cooling system must also be addressed periodically to ensure proper cooling and component reliability. Plastic and rubber components become brittle and prone to splitting or cracking after long periods of heating and cooling cycles, especially in colder climates! The coolant itself can degrade or become contaminated, leading to potential corrosion or freezing issues. Finally, thermostats and sensors can fail completely, preventing proper cooling and/or coolant temperature readings to become inaccurate.

To make sure you are not left stranded on the side of the road with an overheated engine, we have put together this Basic Cooling System Service kit. This kit contains all of the most-likely-to-fail components, giving you peace of mind knowing your engine will continue to run cool for another 60,000+ miles.

See kit contents below for all included components.

N54 HPFP failure is common with BMWs that use this powerplant. Our Packaged by Turner N54 High Pressure Fuel Pump Replacement Kit includes everything you need to replace your N54 HPFP.

Kit includes:

• Genuine BMW Re-manufactured High pressure fuel pump
• Intake manifold gasket sets  
• Throttle body gasket 
• Low pressure fuel sensor 
• High pressure fuel sensor 

2006-2007 E60 530i Stage 1 Performance Package
Peak Power Gain: +29hp / +29ft-lbs
Rev limit: 7000
Octane: 91 or higher

Our Stage 1 kit featuring a cold-air intake kit and matching performance software. The aFe intake is a cone filter with a heat-blocking shield around it. The larger surface area of the filter, combined with the heat shield, allow more cool air to enter the engine - creating more power and torque, a richer engine sound, and better throttle response. The kit is supplied complete with heat shield, intake tube, sealing materials, hardware, and install instructions.

Our flash software is tuned especially for a cold-air intake, maximizing the potential and providing smoother power delivery. We take the stock software and make adjustments for 91 octane (stock software is set around 87). We can get more power and torque, and increase fuel efficiency without affecting driveability or the life of the engine. The throttle response is also improved (quicker) eliminating unwanted and dangerous flat spots in the pedal response.

Our software fully maximizes the 'low-output' N52B30O0 engine in the 530i. Our software has been carefully developed on the dyno and the road to provide optimal power and torque gains at all RPM. We change the fuel, Valvetronic, and VANOS maps as well as revise the factory torque limiters. We have paid particular attention to increasing low and mid-range torque. The stock BMW software is hampered by settings for 87 octane fuel. By re-mapping the engine programming for 91 octane, we can make more power, torque, and improve fuel mileage - all without harm to the engine or affecting driveability. The throttle response is also improved (quicker) eliminating unwanted and dangerous flat spots in the pedal response.

There are two ways to install our software: mailing the ECU to us for a reflash or do-it-yourself install with our Turner Flash tool:

Mail-In Reflash - lower upfront cost but additional shipping charges. Minimum downtime of at least three days. We have a 24 hour turnaround on shipping the ECU back to you but factor in transit time. Expert installation of your software at our facility.
Turner Flash DIY tool - higher upfront cost but files are emailed back and forth. No downtime - you can still drive the car while we process your tune. Files are emailed back and forth - your stock file comes to us, a tuned file is returned to you. Easy install via Windows laptop. 

E60 530i Stage 1 Engine Upgrade includes:
aFe Cold Air Intake (filter, heat shield, intake tube)
Turner Motorsport Performance Software Flash

This item fits the following BMWs:
2006-2007 E60 BMW 530i 530xi

Often an oversight in maintenance, ignition components are also susceptible to wear and tear. Spark Plugs can accumulate carbon, reducing the spark intensity and it's ability to properly ignite the air/fuel mixture, leading to misfires and generally declining performance. Other ignition components, such as coils, boots, wires, caps, and rotors, can also wear out over time due to factors like heat and contamination, preventing the current from reaching the spark plug.

To start over fresh with all new components, we now offer these Ignition Service Kits. Each kit comes with brand new OE quality components, replacing any potential fault points in your ignition system for peak performance!

See kit contents below for a complete list of included components.

Maintain your BMW's cooling system and avoid costly repairs with our comprehensive Water Pump and Thermostat Replacement Kit, meticulously crafted by the experts at Turner Motorsport! Designed to service BMW models with the N62 engine, this kit ensures your vehicle runs at optimal temperature, preventing overheating and extending engine life.

Key Benefits:

All-Inclusive Kit: This package includes everything you need for a complete cooling system overhaul, saving you time and effort sourcing individual components. High-Quality Components: Each part in this kit is manufactured to meet or exceed OEM standards, guaranteeing reliable performance and longevity. Optimal Cooling Performance: Regularly replacing your water pump and thermostat every 60,000 miles is crucial for maintaining peak cooling efficiency. Our kit ensures your BMW's engine stays within the ideal temperature range, preventing overheating and potential engine damage. Enhanced Reliability: By including premium components like the Wahler Thermostat and Graf Water Pump, this kit provides enhanced durability and peace of mind. Kit Contents:

Wahler Thermostat (Part #11537586885): Renowned for its precision and reliability, ensuring your engine maintains the correct operating temperature. Graf Water Pump (Part #11517586779): High-performance pump designed for consistent and efficient coolant circulation. Genuine BMW Hex Bolts (M6x25) (Part #07119905400): Essential hardware for secure installation. Genuine BMW Hex Bolts (M6x40) (Part #07119904525): Ensures all components are firmly in place. Genuine BMW Coolant/Antifreeze (Diluted, 1 Gallon) (Part #82141467704): Formulated specifically for BMW cooling systems, providing optimal protection against corrosion and freezing. Upgrade your BMW N62 cooling system with this expertly curated Water Pump and Thermostat Replacement Kit. Perfect for maintaining the health and efficiency of your engine, this kit is an essential investment for any BMW enthusiast. Order now from Turner Motorsport and ensure your vehicle performs at its best.

Tired of dealing with excess shifter slop and a mushy shifter? The Turner Shifter Rebuild & Upgrade Kits will restore your shifter's crisp feel and eliminate excessive movement that develops over time with wear. Included in this kit are all the common wear components and OE quality bushings that will give you a tighter shifting feel and will hold up like a day 1 BMW.

This kit is perfect to restore your driving pleasure!

See the included components under Kit Contents below.

Tired of dealing with excess shifter slop and a mushy shifter? The Turner Shifter Rebuild & Upgrade Kits will restore your shifter's crisp feel and eliminate excessive movement that develops over time with wear. Included in this kit are all the common wear components and upgraded bushings that will give you a tighter shifting feel than traditional rubber bushings and will resist wear significantly longer.

This kit is perfect to restore your driving pleasure and will be the last shifter rebuild you will ever need!

See the included components under Kit Contents below.

Drive line slop is often caused by faulty engine and transmission mounts. This can result in knocking noises under heavy acceleration, excessive vibration, and a less responsive feel in power. These Genuine BMW mounts are perfect to eliminate these problems and provide long lasting reliability.

Included in this kit:

• Genuine BMW Engine Mount (Left and Right Sides)
• Genuine BMW Transmission Mount (x2)
• New Installation Hardware

This is a compete cooling system overhaul kit, which includes all the common cooling system failure parts bundled into a complete package. This cooling system package is for the 2008-2010 E60 528i/528xi models with an automatic transmission (N52 engine).

Much of the later E60 cooling system is strong and reliable compared to the previous generation 5-series models. But there is still the potential for serious cooling system and engine-related failures. On the N52 engine the electric water pump is the weakest link. It will fail without much warning and shut down the engine. Preventative replacement is the best course of action and the water pump and thermostat should be done before they reach 60,000 miles. Several other cooling components are due for replacement by 100,000 miles to prevent other breakdowns. A failure in the cooling system can lead to overheating and catastrophic engine failure. Don't gamble your engine! By replacing these core items preventatively you are defusing what could be a ticking cooling system time bomb. And if you've had a failure of one of these parts, now is the time to refresh your entire cooling system.

Our base kit comes with the OEM Behr thermostat, Original BMW electric water pump with mounting screws, and the u-shaped hose between the pump and thermostat. From there you can add additional items to complete the overhaul - radiator, expansion tank, cap, and new radiator hoses..

E60 528i Automatic Radiator Options. There are two styles of radiators for the E60 6-cylinder and automatic transmission: original and updated. You can use either radiator as long as you have the correct corresponding parts to go with it. Both radiators are still available from BMW or the OE supplier Behr. If it were up to us we would prefer the updated style because it won't cause any confusion down the road and it reduces the number of potential leak points by eliminating an unnecessary fitting.

• Original, BMW #17117534914. This setup has an extra fitting for the engine oil heat exchanger along with a hose that attaches to the water pump pipe and heat exchanger. In order to use this radiator you must use the corresponding hose. This was the original setup as the car was built at the factory and is pictured in the radiator image to the right. At some point BMW stopped listing this part number in their official diagrams and used the 209 number below.
• Updated, BMW #17117519209. This is the updated style from BMW. If your radiator was replaced at some point after 2010 it most likely has this radiator style. On this radiator they did away with the extra fitting for the heat exchanger. When looking at the ETK or RealOEM diagrams it will only list this radiator but with a note saying you also need two compensators (spacer blocks, #17117520335) and the hose (11537519494).

Click here for diagrams of both E60 radiator options.

E60 528i Cooling Hoses. There are a lot of hoses on the N52 engine. Not all of them need to be replaced during an overhaul but it would be a good idea. The hoses themselves don't wear but the metal spring clips on the connector lose their tension over time and that can lead to a leak. It's worse when re-using a hose after it's already been disconnected. Since our package includes the thermostat, water pump, and radiator we offer all of the hoses related to those components. Use the diagram on the right to see where each is connected in the engine bay. Evaluate your current hoses and then decide which ones to replace. One note about the lower radiator hose: when ordering a new hose you must order a new temp sensor. Do not reuse the original temp sensor as it will leak on the new hose.

This item fits the following BMWs:
2008-2010 E60 BMW 528i 528xi with automatic transmission

The cooling system is one of the major weak points on the N62 engine in the 550i/650i. The water pump itself won't last more than 100,000 miles in most cases and the engine itself is prone to coolant leaks from multiple locations. So a major 550i cooling system overhaul should be planned before the 100,000 mile mark. Aside from obvious leaks the 550i water pump will also squeal or screech indicating the bearings inside have worn. This package covers the water pump, thermostat, and radiator for the 2006-2010 E60 550i and E63 650i with a manual transmission.

The entire cooling system on the 550i is susceptible to leaks and poor performance. The condition of the rest of the cooling system should be considered along with the water pump and thermostat. Replacing the water pump will expose the front of the V8 engine where more problem areas may appear so plan accordingly. The biggest problem is the V8 valley pan gaskets and inner coolant tube seals. The tube carrying coolant through the valley is prone to leaking and replacement is a major job (see our valley pan pipe kit here). Additional items recommended to be replaced during the water pump job are: cooling hoses, expansion tank and cap, temp sensors, drive belts, and pulleys and tensioners.

Base 550i/650i Cooling Package includes:

• OEM Behr radiator (17117519210)
• OEM water pump (11517586779)
• water pump pipe (back of pump to engine block) (11511439976)
• OEM thermostat (11537586885)
  
• BUY AS A PACKAGE AND SAVE $$!
  
  This item fits the following BMWs:
  2006-2010 E60 BMW 550i with manual transmission
  2006-2011 E63 BMW 650i with manual transmission