Packaged by Turner for BMW 5 Series E60 (2004-2010)

Our water pump/thermostat overhaul includes:

• Electric Water Pump
• Aluminum mounting screws for water pump
• Thermostat
• Connecting hose from thermostat to water pump 
• Hose clamps

2006-2007 E60 530i Stage 1 Performance Package
Peak Power Gain: +29hp / +29ft-lbs
Rev limit: 7000
Octane: 91 or higher

Our Stage 1 kit featuring a cold-air intake kit and matching performance software. The aFe intake is a cone filter with a heat-blocking shield around it. The larger surface area of the filter, combined with the heat shield, allow more cool air to enter the engine - creating more power and torque, a richer engine sound, and better throttle response. The kit is supplied complete with heat shield, intake tube, sealing materials, hardware, and install instructions.

Our flash software is tuned especially for a cold-air intake, maximizing the potential and providing smoother power delivery. We take the stock software and make adjustments for 91 octane (stock software is set around 87). We can get more power and torque, and increase fuel efficiency without affecting driveability or the life of the engine. The throttle response is also improved (quicker) eliminating unwanted and dangerous flat spots in the pedal response.

Our software fully maximizes the 'low-output' N52B30O0 engine in the 530i. Our software has been carefully developed on the dyno and the road to provide optimal power and torque gains at all RPM. We change the fuel, Valvetronic, and VANOS maps as well as revise the factory torque limiters. We have paid particular attention to increasing low and mid-range torque. The stock BMW software is hampered by settings for 87 octane fuel. By re-mapping the engine programming for 91 octane, we can make more power, torque, and improve fuel mileage - all without harm to the engine or affecting driveability. The throttle response is also improved (quicker) eliminating unwanted and dangerous flat spots in the pedal response.

There are two ways to install our software: mailing the ECU to us for a reflash or do-it-yourself install with our Turner Flash tool:

Mail-In Reflash - lower upfront cost but additional shipping charges. Minimum downtime of at least three days. We have a 24 hour turnaround on shipping the ECU back to you but factor in transit time. Expert installation of your software at our facility.
Turner Flash DIY tool - higher upfront cost but files are emailed back and forth. No downtime - you can still drive the car while we process your tune. Files are emailed back and forth - your stock file comes to us, a tuned file is returned to you. Easy install via Windows laptop. 

E60 530i Stage 1 Engine Upgrade includes:
aFe Cold Air Intake (filter, heat shield, intake tube)
Turner Motorsport Performance Software Flash

This item fits the following BMWs:
2006-2007 E60 BMW 530i 530xi

Don't buy into the hype that your car is maintenance-free! It was only free during the BMW warranty period, which simply deferred maintenance. Take charge of the care and servicing of your investment and it will reward you in driving pleasure and in your bank account. Using a preventative service schedule will not only keep your BMW running like new, but will also prevent a more costly repair and inconvenience in the future. Not to mention, complete and thorough maintenance records can add hundreds or thousands to a selling price of a used car and give a buyer unmatched piece-of-mind.

Our approach to servicing and caring for newer BMW models is not radically different than when we opened nearly twenty years ago. The design and materials of some components have changed but that only affects WHEN you should replace something, not IF. Through our own Service Department, and thousands of sales annually, we have put together packages for your newer BMW model that will re-inject some life into your car and keep it performing at its peak. We use Original Equipment (OE) or Original Equipment Manufacturer (OEM) parts that we have trusted since we opened in 1993. In some cases, we recommend a performance alternative part that we have found works better, or resolves a design flaw, with the original. So you get top quality parts, first-rate service, and unbeatable expertise.

The LL-01 BMW oil specification marks stringent requirements from BMW that oil must meet in order to receive this approval rating. Still used today in many BMW NA and Turbo engines, LL-01 TwinPower Turbo 5w-30 and all LL-01 approved oils are great for ensuring proper wear protection and low fuel consumption, even during high oil change intervals. When BMW LL-04 oil was developed, it was not approved at the time for use in the US. This was due to the high sulfur and ethanol content in US fuels. Originally used mostly for diesel engines and euro motors, LL-04 demand is now starting to pick up with changes in US fuels such as lower sulfur content since 2014 and thanks to LL-04 and LL-01 being interchangeable/compatible. The slight advantage of LL-04 over LL-01 is due to LL-04's higher ZDDP levels and HTHS ratings. This allows for increased engine protection at higher temperatures and engine pressures. In addition, LL-04 also has a lower SAPS level which benefits direct-injection engines, including all BMW turbo engines since 2007.

5,000 Mile Oil Service

(click to expand)

• engine oil change with filter, using OE BMW 5W30 or Motul
• replace drain bolt crush washer
• reset oil service/maintenance indicator
• inspect and top off any other fluids

Annual Service

(click to expand)

• air filter cleaning or replacement
• MAF/airflow sensor cleaning
• A/C microfilter/cabin filter replacement
• brake fluid flush/bleeding
• top off power steering fluid (make sure you use the correct Pentosin fluid!)
• wiper blade replacement
• lubricate door hinges and treat rubber door seals
• inspect spare tire or tire repair kit, and tire-changing tools
• inspect drive belt for cracking or stretching
• inspect intake boots and vacuum lines for cracks
• inspect brake system for pad wear, rotor wear, parking brake operation, and brake pedal pressure
• inspect bushing and ball joints for excess play/movement
• ensure the cooling systems are functioning correctly (hoses and thermostat, thermostat housing, auxiliary fan, A/C system, etc)

40,000 Mile Major Service

(click to expand)

• spark plug replacement
• ignition coil and coil boot inspection and replacement
• inspect spark plug cavity in valve cover for leaking valve cover gasket
• engine oil change with filter, using OE BMW 5W30 or Motul
• reset oil service/maintenance indicator
• air filter replacement or cleaning for aFe/K&N type
• fill and bleed cooling system
• manual transmission fluid change, using Red Line ATFD4 or Motul Multi ATF
• differential fluid change, using Red Line 75/90 or Motul Gear300
• brake fluid flush/bleeding
• serpentine belt replacement
• inspect belt roller pulleys (drag and rotation) and belt tensioners
• complete chassis inspection, including: front control arms, tie rods, ball joints, wheel bearings, rear suspension arm bushings, rear upper shock mounts, rear subframe mounts, axle shaft boots
• complete brake system test and inspection
• engine and transmission leak detection and diagnosis
• shifter linkage, driveshaft guibo, CV, and center support bearing inspection
• exhast system inspection, including hanger replacement

80,000 Mile Major Service

(click to expand)

• spark plug replacement
• ignition coil and coil boot inspection and replacement
• inspect spark plug cavity in valve cover for leaking valve cover gasket
• engine oil change with filter, using OE BMW 5W30 or Motul
• reset oil service/maintenance indicator
• air filter replacement or cleaning for aFe/K&N type
• fill and bleed cooling system
• manual transmission fluid change, using Red Line ATFD4 or Motul Multi ATF
• differential fluid change, using Red Line 75/90 or Motul Gear300
• brake fluid flush/bleeding
• fuel filter, pressure regulator replacement
• serpentine belt replacement
• replace belt roller pulleys and belt tensioners
• complete chassis inspection, including: front control arms, tie rods, ball joints, wheel bearings, rear suspension arm bushings, rear upper shock mounts, rear subframe mounts, axle shaft boots
• complete brake system test and inspection
• engine and transmission leak detection and diagnosis
• shifter linkage, driveshaft guibo, CV, and center support bearing inspection
• exhast system inspection, including hanger replacement
• water pump and thermostat inspection or replacement. The water pump on this car is electric and will not display warning signs of impending failure. The output of the water pump can be tested however, and your local full-service BMW repair shop should have the diagnostic tools to perform this test.

You may also want to pick up these other helpful items:

• Bentley Service Manual
• We offer many DIY-related tools, specifically for the E60 owner -
  drain plug sockets, fluid suction and bleeder pumps, spark plug sockets and install guides, oil filter cap adapter, oil funnels, and more!
• SprintBooster throttle enhancement
  
• This package fits the following BMWs:
  2007-2010 E60 BMW 535i 535xi 535i xDrive
  
  
  
  Put a check in the boxes next to the items you wish to order.

Maintain your BMW's cooling system and avoid costly repairs with our comprehensive Water Pump and Thermostat Replacement Kit, meticulously crafted by the experts at Turner Motorsport! Designed to service BMW models with the N62 engine, this kit ensures your vehicle runs at optimal temperature, preventing overheating and extending engine life.

Key Benefits:

All-Inclusive Kit: This package includes everything you need for a complete cooling system overhaul, saving you time and effort sourcing individual components. High-Quality Components: Each part in this kit is manufactured to meet or exceed OEM standards, guaranteeing reliable performance and longevity. Optimal Cooling Performance: Regularly replacing your water pump and thermostat every 60,000 miles is crucial for maintaining peak cooling efficiency. Our kit ensures your BMW's engine stays within the ideal temperature range, preventing overheating and potential engine damage. Enhanced Reliability: By including premium components like the Wahler Thermostat and Graf Water Pump, this kit provides enhanced durability and peace of mind. Kit Contents:

Wahler Thermostat (Part #11537586885): Renowned for its precision and reliability, ensuring your engine maintains the correct operating temperature. Graf Water Pump (Part #11517586779): High-performance pump designed for consistent and efficient coolant circulation. Genuine BMW Hex Bolts (M6x25) (Part #07119905400): Essential hardware for secure installation. Genuine BMW Hex Bolts (M6x40) (Part #07119904525): Ensures all components are firmly in place. Genuine BMW Coolant/Antifreeze (Diluted, 1 Gallon) (Part #82141467704): Formulated specifically for BMW cooling systems, providing optimal protection against corrosion and freezing. Upgrade your BMW N62 cooling system with this expertly curated Water Pump and Thermostat Replacement Kit. Perfect for maintaining the health and efficiency of your engine, this kit is an essential investment for any BMW enthusiast. Order now from Turner Motorsport and ensure your vehicle performs at its best.