BMW Performance Clutch Kits & Parts for BMW 5 Series E61 (2006-2010)

A lightweight aluminum flywheel is a great way to increase throttle response and free up horsepower by reducing drivetrain loss. Factory flywheels are built to minimize engine and transmission vibrations, making them heavier and requiring more energy to make them spin. An aluminum flywheel can save lots of weight over the stock steel unit - sometimes over 50%. While the dampening effect of the stock flywheel is reduced, most enthusiasts would agree that the increase in performance is well worth it. In addition, the lighter flywheel allows the engine to spin more freely, improving throttle response.

This JB Racing lightweight aluminum flywheel kit and is designed to be used with the included factory clutch, making replacement and service easy and inexpensive, especially compared to specialized racing clutches. It also preserves the driveability of your car on the street, and enthusiasts tolerant of a mild to moderate NVH increase will be especially taken with this setup. In addition, the JB Racing flywheel can be easily rebuilt with a new clutch contact surface, allowing you to enjoy faster revs and superior response for many years to come.

Stock Flywheel Weight: 24-31 lbs.

JB Racing Lightweight Aluminum Flywheel: 12 lbs.

This item fits the following BMW Chassis:
E61/1, E82/88, E9x, Z4

Fits the follow engines:
N52 3.0L

This is an OEM LuK stock twin mass flywheel for the N52 non-turbo engine in the 128i, 325i/328i/330i, 525i/528i/530i, and Z4 30i. It's manufactured by OEM supplier LuK. Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.

The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.

A new pilot bearing (roller bearing) is included, pre-installed in the flywheel hub.

This is the stock twin mass flywheel for the N54 engine in later E82 135i, E9X 335i, E60 535i, and Z4 35i (cars with 6-bolt mounting hub). It's manufactured by OEM supplier LuK. Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.

The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.

Tip: DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.

A new pilot bearing (roller bearing) is included, pre-installed on the flywheel hub.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

This item fits the following BMWs:
1/2009-2010 E82 BMW 135i
1/2009-2010 E90 BMW 335i 335xi 335i xDrive - Sedan
1/2009-2010 E92 BMW 335i 335is 335xi 335i xDrive - Coupe
1/2009-2010 E93 BMW 335i - Convertible
1/2009-2010 E60 BMW 535i 535xi 535i xDrive

Ensure your clutch system can get the all of the power to the wheels. Stock clutch components lack the ability to transmit the full torque and horsepower loads to the wheels without suffering from increased wear and eventual clutch fade. Sachs Performance Clutch Kits are designed for sport and race applications, delivering higher torque transmission without succumbing to wear and tear and fading over extended periods of abuse.

Sachs Performance Clutch Kits include the following upgraded components:

• Performance Pressure Plate - Increased clamping force and resistant to wear

• Performance Clutch Disc - Allows for higher clamping force, higher torque transmission, and better clutch engagement at higher RPM’s

These kits are available with two different clutch discs, Organic and Metallic. Organic clutch discs are perfect for both performance street and light-moderate track applications. Metallic are designed for specifically for full-time track use such as endurance racing, clubsport, autocross, hill climbing and 1/4 mile racing. Please be sure you are purchasing the kit that best fits your needs. Our sales staff can help with any questions or concerns you may have!

Sachs Performance is the racing and performance oriented selection of high quality parts from Sachs and ZF Engineering. Supplying countless brands with OE parts and offering one of the widest selection of OEM replacement parts, they are known for their exceptionally high quality products. You can purchase these performance parts with confidence, knowing they will resist heavy wear and tear for much longer than most other aftermarket options.

Looking to upgrade your clutch disc? This Sachs Performance clutch disc is a great option. Allowing for higher torque and horsepower, this disc is perfect for both performance street and light to moderate track applications such as occasional endurance racing, clubsport, autocross, hill climbing and 1/4 mile racing.

Sachs Performance is the racing and performance oriented selection of high quality parts from Sachs and ZF Engineering. Supplying countless brands with OE parts and offering one of the widest selection of OEM replacement parts, they are known for their exceptionally high quality products. You can purchase these performance parts with confidence, knowing they will resist heavy wear and tear for much longer than most other aftermarket options.