BMW 6 Series E64 (2004-2010)

APEX M12x1.5mm BMW 5 Lug Stud Kit - Hex head Black Finish - 75mm Leng...

2X Entries For Our G87 M2 Sweepstakes!

T#:637384

Part#: APEXM12STDKIT5HX

Ships in 2 Business Days

$ 160.00 USD

Add to Wish List

Qty

$ 160.00 USD

Add to Wish List

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E36, E39 ...

T#:389645

Part#: 192416-1J

In Stock

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

Tire Valve For TPMS Systems

T#:641919

Part#: AUL1SENSOR

In Stock

Sale - Save 29% $ 60.96

This product was last offered at the strikethrough price on
05-15-2026

$ 43.02 USD

Add to Wish List

Qty

Sale - Save 29%

$ 60.96

This product was last offered at the strikethrough price on
05-15-2026

$ 43.02 USD

Add to Wish List

12g Lower MX-Sensor weight is significantly lighter than most sensors ensures greater security and stability for durable use

APEX ARC-8 18x9.5" ET22 Race Silver Wheel 19.2lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:342500

Part#: ARC81895ET22RS

Back Ordered

$ 399.00 USD

Add to Wish List

Qty

$ 399.00 USD

Add to Wish List

Silver 18x9.5" ET22 Concave APEX ARC-8 Wheel.

Wheel Specs

Fitment:Rear

Size:18x9.5"

Offset (mm):22

Weight (lbs):19.2

Profile:Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit many BMW models and may fit other models with a specific wheel spacer. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

18x10.5" ET22 Brushed Clear APEX VS-5RS Forged BMW Wheel

2X Entries For Our G87 M2 Sweepstakes!

T#:4607237

Part#: VS5RS18105ET22BC

Ships in 5 Business Days

$ 799.00 USD

Add to Wish List

Qty

$ 799.00 USD

Add to Wish List

APEX ARC-8 18x9.5" ET22 Satin Black Concave Wheel 19.2lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:180708

Part#: ARC81895ET22SMBK

In Stock

$ 399.00 USD

Add to Wish List

Qty

$ 399.00 USD

Add to Wish List

18x9.5" ET22 Satin Black Concave APEX ARC-8 Wheel 19.2lbs

Wheel Specs
Fitment:	Rear
Size:	18x9.5"
Offset (mm):	22
Weight (lbs):	19.2
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

BMC Filter Cleaning Kit

T#:590913

Part#: WA250-500

In Stock

$ 24.99 USD

Add to Wish List

Qty

$ 24.99 USD

Add to Wish List

APEX ARC-8 19x9.5" ET22 Satin Black Wheel 20.95lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201386

Part#: ARC81995ET22SMBK

Ships on Oct 22, 2026

$ 449.00 USD

Add to Wish List

Qty

$ 449.00 USD

Add to Wish List

19x9.5" ET22 APEX ARC-8 Wheel 20.95lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x9.5"
Offset (mm):	22
Weight (lbs):	20.95
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX EC-7 19x9.5" ET22 Silver Wheel 22.9lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201363

Part#: EC71995ET22RS

Ships in 5 Business Days

$ 459.00 USD

Add to Wish List

Qty

$ 459.00 USD

Add to Wish List

Silver 19x10" ET25 APEX EC-7 Wheel.

Wheel Specs
Fitment:	Mostly Rear
Size:	19x9.5"
Offset (mm):	22
Weight (lbs):	22.9
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to many BMW models and may fit other models when used with a specific spacer. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX ARC-8 19x9.5" ET22 Silver Wheel 20.95lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201387

Part#: ARC81995ET22HS

Ships in 5 Business Days

$ 449.00 USD

Add to Wish List

Qty

$ 449.00 USD

Add to Wish List

Silver 19x9.5" ET22 APEX ARC-8 Wheel.

Wheel Specs
Fitment:	Front or Rear
Size:	19x9.5"
Offset (mm):	22
Weight (lbs):	20.95
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit many BMW models and may fit others when used with a specific spacer. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX ARC-8 18x9.5" ET22 Hyper Black Concave Wheel 19.2lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:180709

Part#: ARC81895ET22HBK

Ships in 5 Business Days

$ 409.00 USD

Add to Wish List

Qty

$ 409.00 USD

Add to Wish List

18x9.5" ET22 Hyper Black Concave APEX ARC-8 Wheel 19.2lbs

Wheel Specs
Fitment:	Rear
Size:	18x9.5"
Offset (mm):	22
Weight (lbs):	19.2
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX ARC-8 19x10.5" ET22 Satin Black Wheel 22.95lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201398

Part#: TMS201398

Ships on Oct 22, 2026

$ 458.00 USD

Add to Wish List

Qty

$ 458.00 USD

Add to Wish List

19x10.5" ET22 APEX ARC-8 Wheel 22.95lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x10.5"
Offset (mm):	22
Weight (lbs):	22.95
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX ARC-8 19x10" ET25 Silver Wheel 21.95lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201396

Part#: ARC81910ET25HS

Ships in 5 Business Days

$ 459.00 USD

Add to Wish List

Qty

$ 459.00 USD

Add to Wish List

19x10" ET25 APEX ARC-8 Wheel 21.95lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x10"
Offset (mm):	25
Weight (lbs):	21.95
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX ARC-8 19x10" ET25 Satin Black Wheel 21.95lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201395

Part#: ARC81910ET25SMBK

Ships in 5 Business Days

$ 459.00 USD

Add to Wish List

Qty

$ 459.00 USD

Add to Wish List

19x10" ET25 APEX ARC-8 Wheel 21.95lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x10"
Offset (mm):	25
Weight (lbs):	21.95
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

GSP Front Wheel bearing & hub assembly - E60, E63, E64

T#:389675

Part#: 274210

Ships in 2 Business Days

$ 105.99 USD

Add to Wish List

Qty

$ 105.99 USD

Add to Wish List

Since established in 2004, GSP North America has positioned itself as a leading supplier of New Axles in North America.GSP’s new axle program consistently offers the best application coverage, most SKU count, and more new numbers than any other competitors. GSP’s hub assembly program was introduced to North America market in 2010 and has grown into one the most trustable programs in US market.

This item fits the following BMWs:

E39 BMW 525i 528i 530i

E60 BMW 525i 525xi 528i 528i xDrive 530i 530xi 535i 535xi 545i 550i

E63 BMW 645Ci 650i

Show More Show Less

APEX EC-7 19x10.5" ET22 Silver Wheel 23.9lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201375

Part#: EC719105ET22RS

Ships in 5 Business Days

$ 479.00 USD

Add to Wish List

Qty

$ 479.00 USD

Add to Wish List

19x10.5" ET22 APEX EC-7 Wheel 23.9lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x10.5"
Offset (mm):	22
Weight (lbs):	23.9
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

18x9.5" ET35 Satin Black APEX VS-5RS Forged BMW Wheel

2X Entries For Our G87 M2 Sweepstakes!

T#:4607225

Part#: VS5RS1895ET35SMB

Ships in 5 Business Days

$ 739.00 USD

Add to Wish List

Qty

$ 739.00 USD

Add to Wish List

APEX EC-7 19x10" ET25 Silver Wheel 23.5lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201372

Part#: EC71910ET25RS

Ships in 5 Business Days

$ 469.00 USD

Add to Wish List

Qty

$ 469.00 USD

Add to Wish List

19x10" ET25 APEX EC-7 Wheel 23.5lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x10"
Offset (mm):	25
Weight (lbs):	23.5
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

Adjustable Front Camber Bushings

T#:31522921

Part#: 193616-6H

Ships on Aug 20, 2026

$ 320.00 USD

Add to Wish List

Qty

$ 320.00 USD

Add to Wish List

Extended Spark Plug Socket

T#:391150

Part#: SUU884506

In Stock

9% off MSRP $ 31.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 28.99 USD

Add to Wish List

Qty

9% off MSRP

$ 31.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 28.99 USD

Add to Wish List

3/8" drive socket with 5/8" opening for most spark plugs

Autel Universal Rubber TPMS Sensor - Set Of Four

T#:3529121

Part#: AUL1SENSORKT

In Stock

$ 243.99 USD

Add to Wish List

Qty

$ 243.99 USD

Add to Wish List

Apex EC-7 19" Staggered Wheel Set - Race Silver

2X Entries For Our G87 M2 Sweepstakes!

T#:599071

Part#: EC71995ET28RSKT

Ships in 5 Business Days

$ 1,876.00 USD

Add to Wish List

Qty

$ 1,876.00 USD

Add to Wish List

Specifications: Color - Race Silver Size Front - 19x9.5" ET28 Size Rear - 19x10.5" ET45

APEX EC-7 19" Staggered Wheel Set - Race Silver

2X Entries For Our G87 M2 Sweepstakes!

T#:19560861

Part#: EC71995H105SKT

Ships in 5 Business Days

$ 1,876.00 USD

Add to Wish List

Qty

$ 1,876.00 USD

Add to Wish List

APEX wheels are stronger, lighter wheels than typical cast wheels thanks to their Flow-formed semi-forging process. These wheels are on average 10lbs lighter or more! This reduces unsprung weight, allow for the best performance possible. The spokes and barrel are designed to allow as much room as possible for brake systems, while retaining a classic motorsports theme that matches perfectly with the aggressive BMW style. Thanks to these qualities, these wheels will keep your looks and performing at your best with plenty of confidence!

Show More Show Less

APEX ARC-8 19x9.5" ET22 Anthracite Wheel 20.95lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201388

Part#: ARC81995ET22AN

Ships in 5 Business Days

$ 449.00 USD

Add to Wish List

Qty

$ 449.00 USD

Add to Wish List

19x9.5" ET22 APEX ARC-8 Wheel 20.95lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x9.5"
Offset (mm):	22
Weight (lbs):	20.95
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

OEM Behr A/C Evaporator - E60 E61 E63 E64

T#:150543

Part#: 64119238655

In Stock at Vendor

$ 531.88 USD

Add to Wish List

Qty

$ 531.88 USD

Add to Wish List

The A/C evaporator in your BMW is where the A/C refrigerant is evaporated from a liquid to a gas, absorbing heat in the process. Without the evaporator, the A/C system would not work at all. Since the evaporator is located inside of the vehicle in the climate control plenum, it is not very susceptible to damage. The evaporator will usually last many years. If your A/C evaporator does fail, it must be replaced in order to maintain the functionality of the A/C system.

Show More Show Less

APEX EC-7 19x9.5" ET22 Satin Black Wheel 22.9lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201362

Part#: EC71995ET22SMBK

Ships in 5 Business Days

$ 459.00 USD

Add to Wish List

Qty

$ 459.00 USD

Add to Wish List

19x10" ET25 APEX EC-7 Wheel 23.5lbs.

Wheel Specs
Fitment:	Mostly Rear
Size:	19x9.5"
Offset (mm):	22
Weight (lbs):	22.9
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX EC-7 19"Staggered Wheel Set - Anthracite

2X Entries For Our G87 M2 Sweepstakes!

T#:19560858

Part#: EC71995H105AKT

Ships in 5 Business Days

$ 1,876.00 USD

Add to Wish List

Qty

$ 1,876.00 USD

Add to Wish List

APEX EC-7 19" Staggered Wheel Set -- 19x9.5" / 19x10.5" This set of 9.5" and 10.5" EC-7 wheels is an easy staggered fitment for the E46 M3, E6X M5/6 and Z4M models. These are a direct fit with no spacers or fender rolling required. We use a 9.5" ET22 on the front and a 10.5" ET22 on the rear. These are only slightly wider than the stock sizes. The rear wheels have a deeper concave face than the fronts, emphasizing the RWD chassis and adding some muscularity to the stance. APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still lightweight. The wheels are around 10 lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand. Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required.

Show More Show Less

Autel Autolink AL329

T#:2914116

Part#: AL329

Ships in 1 Business Day

$ 49.99 USD

Add to Wish List

Qty

$ 49.99 USD

Add to Wish List

OBDII Code Reader

7 pc. 3/8" Dr. Spark Plug Socket Set

T#:641915

Part#: 8845D

Ships in 6 Business Days

$ 141.99 USD

Add to Wish List

Qty

$ 141.99 USD

Add to Wish List

Complete set of spark plug sockets.

APEX ARC-8 19" Staggered Wheel Set - Satin Black

2X Entries For Our G87 M2 Sweepstakes!

T#:599190

Part#: ARC819105ET22KT2

Ships on Oct 22, 2026

$ 1,814.00 USD

Add to Wish List

Qty

$ 1,814.00 USD

Add to Wish List

Specifications: Color - Satin Black Size Front - 19x9.5" ET22 Size Rear - 19x10.5" ET22

ACM A/C Pressure Sensor

T#:370959

Part#: 64539181464

In Stock at Vendor

10% off MSRP $ 56.57

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 50.99 USD

Add to Wish List

Qty

10% off MSRP

$ 56.57

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 50.99 USD

Add to Wish List

Part of the A/C system

APEX EC-7 18x10" ET25 Silver Wheel 22.45lbs - PROFILE 3

2X Entries For Our G87 M2 Sweepstakes!

T#:180721

Part#: EC71810ET25RS

Ships in 2 Business Days

$ 419.00 USD

Add to Wish List

Qty

$ 419.00 USD

Add to Wish List

Silver 18x10" ET25 Concave APEX EC-7 Wheel.

Wheel Specs
Fitment:	Rear
Size:	18x10.0"
Offset (mm):	25
Weight (lbs):	22.45
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit many BMW models and may be used on other models with a specific wheel spacer. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX EC-7 19x10" ET25 Anthracite Wheel 23.5lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201373

Part#: EC71910ET25AN

Ships in 5 Business Days

$ 469.00 USD

Add to Wish List

Qty

$ 469.00 USD

Add to Wish List

19x10" ET25 APEX EC-7 Wheel 23.5lbs.

Wheel Specs
Fitment:	Mostly Rear
Size:	19x10"
Offset (mm):	25
Weight (lbs):	23.5
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

AutoLink AL529HD

T#:2914129

Part#: AL529HD

Ships in 6 Business Days

$ 264.99 USD

Add to Wish List

Qty

$ 264.99 USD

Add to Wish List

Autel’s latest member of its code reader family of tools, the AL529HD can not only diagnose OBDII/EOBD-compatible vehicles but also heavy duty vehicles utilizing SAE-J1939 and SAE-J1708 protocols.

1/2" Drive 24mm Universal Impact Socket

T#:5229449

Part#: 224UMD

Ships on Aug 17, 2026

$ 29.99 USD

Add to Wish List

Qty

$ 29.99 USD

Add to Wish List

Deep Impact Socket on a swivel.

3/8" Dr. Universal Impact Swivel Joint

T#:2528135

Part#: 3301D

Ships on Aug 17, 2026

5% off MSRP $ 26.20

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 24.89 USD

Add to Wish List

Qty

5% off MSRP

$ 26.20

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 24.89 USD

Add to Wish List

Designed for impact use

3/8" Dr. External Star Impact Socket Set

T#:5269512

Part#: 3670SED

Ships on Aug 17, 2026

$ 65.99 USD

Add to Wish List

Qty

$ 65.99 USD

Add to Wish List

CR-MO alloy steel for long life

14 Pc. Full Polish SAE Angle Head Wrench Set

T#:642035

Part#: 9914A

Ships on Aug 17, 2026

$ 113.91 USD

Add to Wish List

Qty

$ 113.91 USD

Add to Wish List

Radius V-Groove design creates an anti-slip while also preventing round-off.

KMAC Stage 3 Track Front Adjustable Camber/Caster Plates - E39 540/M5...

T#:389662

Part#: 193616-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Track, Stage 3
Bearing: PTFE-lined pillow-ball, no bushing

KMAC Stage 3 camber/caster plates are designed for track or race-only situations where comfort and noise are not the primary concerns. The Stage 3 camber plates use a pillowball bearing, solidly mounted within the camber plate for direct alignment of the strut shaft and no excess play or deflection. Stage 3 are designed to increase negative camber with their patented 'floating' adjustment that changes camber and caster together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Fitment is limited to race-only small diameter coil-over springs (not stock-type). Bearing inserts and adapters included. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1997-2003 E39 BMW 525i 528i 530i 540i (for cars with EDC)
1999-2003 E39 BMW M5
1995-2001 E38 BMW 740i 740il 750il (for cars with EDC)
2004-2010 E60 BMW M5
2004-2011 E63 BMW M6

Show More Show Less

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E39...

T#:389317

Part#: 193616-2L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearing: PTFE-lined pillow-ball with thin polyurethane bushing

The Stage 2 KMAC plates are a mixed street/track camber/caster plate meant to be used in a variety of suspensions. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions. Bearing inserts and adapters included. The Stage 2 camber plates are shorter than a factory mount so may not be suitable for cars will little suspension travel. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E36...

T#:389647

Part#: 192416-2L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 2 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

KMAC Stage 3 Street/Track Front Adjustable Camber/Caster Plates - E36...

T#:389646

Part#: 192416-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 3 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

KMAC Street Rear Adjustable Camber/Toe Bushings - E60 E63 E65 E53 X5 ...

T#:389668

Part#: 193726J

Special Order: No Guaranteed ETA

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Perfect for lowered cars that need to dial out negative camber to preserve tires. Also perfect for track cars - easily dial in toe and camber for the track for better handling. Priced per set. Fits BMW E60 E63 E65.

This item fits the following BMWs:
2004-2010 E60 BMW 525i 525xi 528i 528xi 530i 530xi 535i 535xi 545i 550i M5
2004+ E63 BMW 645ci 650i M6
2002-2008 E65 BMW 745i 745li 750i 750li 760i 760li
2000-2006 E53 BMW X5 3.0i, X5 4.4i, X5 4.6is, X5 4.8is

Show More Show Less

19" APEX EC-7 Staggered Wheel Set - Pick Your Finish

2X Entries For Our G87 M2 Sweepstakes!

T#:19593915

Part#: EC71995H105

Back Ordered

Starting at $ 1,876.00 USD

Add to Wish List

Starting at $ 1,876.00 USD

Add to Wish List

APEX EC-7 19" Staggered Wheel Set -- 19x9.5" / 19x10.5" This set of 9.5" and 10.5" EC-7 wheels is an easy staggered fitment for the E46 M3, E6X M5/6 and Z4M models. These are a direct fit with no spacers or fender rolling required. We use a 9.5" ET22 on the front and a 10.5" ET22 on the rear. These are only slightly wider than the stock sizes. The rear wheels have a deeper concave face than the fronts, emphasizing the RWD chassis and adding some muscularity to the stance. APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still lightweight. The wheels are around 10 lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand. Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required.

Show More Show Less

Behr Radiator - E60, E61, E63, E64

For vehicles with manual transmission

T#:579569

Part#: 376755591

Back Ordered

$ 267.99 USD

Add to Wish List

Qty

$ 267.99 USD

Add to Wish List

Replace your leaking radiator

2 Ton Long Lowrider Service Jack

T#:385986

Part#: 6602LPD

Back Ordered

$ 704.99 USD

Add to Wish List

Qty

$ 704.99 USD

Add to Wish List

Designed to reach far under your vehicle with this long and low chassis

18" APEX ML-10RT Forged Wheels - Staggered Set Of Four

2X Entries For Our G87 M2 Sweepstakes!

T#:31788333

Part#: ML10181040120AKT

Ships in 5 Business Days

$ 2,956.00 USD

Add to Wish List

Qty

$ 2,956.00 USD

Add to Wish List

18" APEX ML-10RT Forged Wheels - Staggered Set Of Four

2X Entries For Our G87 M2 Sweepstakes!

T#:31788329

Part#: ML10181040120GKT

In Stock

$ 2,956.00 USD

Add to Wish List

Qty

$ 2,956.00 USD

Add to Wish List

Motorsport Gold paint with Machined lip, Staggered Set 18x9 ET30/18x10 ET40 5x120 72.56CB

Oil Filter Socket 32mm

T#:5269518

Part#: 367132D

In Stock

6% off MSRP $ 17.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 15.95 USD

Add to Wish List

Qty

6% off MSRP

$ 17.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 15.95 USD

Add to Wish List

Make oil filter housing removal simple

A/C O-Ring (10.8mm Diameter)

T#:3018037

Part#: 64508375741

In Stock

$ 3.99

This product was last offered at the strikethrough price on
05-07-2026

$ 2.99 USD

Add to Wish List

Qty

$ 2.99 USD

Add to Wish List

O-Rings are used to seal various items and without them, you might experience a leak in your vehicle. When doing any sort of work on your air conditioning system, be sure to use new O-Rings to ensure a proper seal. Getting the correct O-Rings can be a chore, but ECS Tuning has made it easy.

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results