Search | Turner Motorsport

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E32, E34 ...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:389663

Part#: 193416-1J

Special Order: No Guaranteed ETA

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included. This KMAC part number replaces BMW part number 31 33 1 139 437, the strut mount with the integrated upper spring plate.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1988-8/92 E34 BMW 525i
1989-1995 E34 BMW 530i 535i 540i M5
1988-1994 E32 BMW 735i 735il 740i 740il 750il

K-MAC Stage 2 Street/Race - Front Adjustable Camber/Caster Plates - M...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:387691

Part#: 195216-2L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2

KMAC camber/caster plates use a patented adjustment method designed for easy and rapid alignment adjustments. The KMAC design has a 'floating' inner camber plate, rather than slotted, to allow camber and caster to be adjusted together. To adjust, simply loosen the top three nuts on the strut tower and position the KMAC mount to match your desired alignment settings. The KMAC design allows more camber and caster adjustment because separate caster hardware is eliminated. While primarily designed to increase negative camber for track use these can also be used to fix alignment issues that cause uneven tire wear or unwanted handling behavior.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

Fits the following Mini Chassis:
R55, R56, R57, R56, R59, R60, R61

K-MAC Stage 1 Street - Front Adjustable Camber/Caster Plates ...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:388809

Part#: 195216-1J

Special Order: No Guaranteed ETA

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

K-MAC Stage 3 Full Race - Front Adjustable Camber/Caster Plates ...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:387690

Part#: 195116-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

KMAC Stage 3 Track Front Adjustable Camber/Caster Plates - E24, E28, ...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:389656

Part#: 193316-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Track, Stage 3
Bearing: PTFE-lined pillow-ball, no bushing

KMAC Stage 3 camber/caster plates are designed for track or race-only situations where comfort and noise are not the primary concerns. The Stage 3 camber plates use a pillowball bearing, solidly mounted within the camber plate for direct alignment of the strut shaft and no excess play or deflection. Stage 3 are designed to increase negative camber with their patented 'floating' adjustment that changes camber and caster together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Fitment is limited to race-only small diameter coil-over springs (not stock-type). Bearing inserts and adapters included. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is M3
1982-1988 E28 BMW 528e 533i 535i 535is M5
1993-1995 E34 BMW 525i
1982-1989 E24 BMW 633csi 635csi M6