BMW Engine Parts for BMW X Series E70 (2007-2013)

Every 60-80,000 miles, we recommend replacing your spark plugs to ensure your ignition system is running optimally. Over time carbon can build up around the head of the spark plug and decrease spark strength and effectiveness, leading to weaker fuel mixture detonation, misfires, and potential check engine lights. To prevent this, have put together our High-Performance Ignition Service Kits. These kits include new Bav Auto High-Performance Ignition Coils, new spark plugs, dielectric grease, and a BMW spark plug service label to keep track of when your spark plugs were replaced.

Bav Auto's Ignition coils feature core windings that have been modified to increase firepower and promote a faster, more efficient burn. This gives your BMW/MINI increased torque in the lower range of RPM and more horsepower in the upper range. Exact improvements depend on the current condition of your engine, but you'll definitely feel the difference. They'll also improve your fuel economy.

From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Rein Oil Supply Line is a critical component engineered to ensure your BMW’s engine receives the proper oil flow it needs for optimal performance. This high-quality oil supply line is designed to withstand the extreme heat and pressure generated by BMW engines, delivering consistent lubrication to essential engine parts. Available at Turner Motorsport, the Rein Oil Supply Line is a perfect replacement or upgrade for maintaining your engine's longevity and reliability.

• Specifically designed for BMW engines
• Ensures consistent oil flow to critical engine components
• Protects against engine wear by providing efficient lubrication
• Engineered to resist high temperatures and pressure
• Direct-fit for a simple and easy installation
• Manufactured from durable materials for long-lasting performance

The Rein Oil Supply Line from Turner Motorsport is the ideal solution to keep your BMW’s engine running smoothly, ensuring long-term reliability and enhanced performance.

The GENIUS2 is NOCO's most potent charger yet. This energy-efficient and compact device is designed to handle both 6-volt and 12-volt batteries, functioning as a charger, maintainer, and desulfator all in one. With a 2-amp rating, it's suitable for various lead-acid batteries used in automotive, marine, and deep-cycle applications, including flooded, gel, AGM, maintenance-free types, as well as lithium-ion batteries.

Features:

• Meet the GENIUS2 - Similar to the G1100, just better. It's 30% smaller and delivers 140% more power. And it's simpler and easier to use than ever before.
• Do more with Genius - Designed for 6-volt and 12-volt lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion batteries.
• Enjoy precision charging - An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates.
• Charge dead batteries - Charges dead batteries as low as 1-volt. Or use the all-new Force Mode that allows you to take control and manually begin charging dead batteries down to zero volts.
• Simple to set up and use - Plug-in, connect to the battery, select a charge mode, and start charging your battery. A fully-automatic, worry-free battery charger for year-round use.
• Restore your battery - Detects sulfation and acid stratification and restores lost performance for stronger engine starts and extended battery life.
• Compatible with all types of vehicles - Charge and maintain cars, motorcycles, lawnmowers, ATVs, tractors, trucks, SUVs, boats, classic cars, hot rods, and more - you name it.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

• All-in-one valve cover overhaul
• Preventative replacement saves time and trouble later on
• Includes new oil separator system
• Replace valve cover gaskets before a leak becomes worse
• Replace valve cover before it cracks

For the 2007 model year BMW switched to a plastic valve cover on the N51 and N52 engines. As we have seen over time the plastic can crack which leads to oil leaks, vacuum leaks, poor running, and other issues. Unfortunately, it's not just the gasket that needs periodic replacement but the entire valve cover itself. This kit includes a new valve cover, gaskets, eccentric shaft seal, and hardware. The valve cover also incorporates the oil separator which is not a replaceable item on its own. So a complete valve cover replacement will tackle multiple problem areas at once. The valve cover is the same for N51 SULEV and N52 engines.

Cracked Valve Cover. The plastic used for the N52 valve cover is thin and weak in certain spots. This makes it prone to hairline or larger cracks that will leak oil and cause vacuum leaks. You might also notice rough running, especially at idle. Often a technician will go looking for a failed ignition coil, spark plug, or failed vacuum hose on the engine. And without a fault code to assist in diagnosis this can often mean wasted time and money. A cracked valve cover is a new problem area that many techs don't think to check.

Oil Separator/Crankcase Vent. BMW integrated the oil separator system into the valve cover on these later engines. An internal manifold creates a cyclone effect and centrifugal force separates vapor from the liquid oil. The liquid oil is supposed to drain through the valve cover and back to the oil pan while the remaining vapor is burned up during combustion. It's a very efficient and environmentally-friendly design with very few moving parts. Unfortunately it's not perfect and eventually the internal passageways will become clogged. This problem is made worse in cars that have short drive cycles, sit for long periods of time, do not have frequent oil changes, do not see regular runs to redline, and cars in freezing climates. If the engine never reaches optimal operating temp the oil remains in liquid form or becomes sludge. This is bad news for the entire engine, leading to fouled spark plugs, rough running and misfires and even premature failure of catalytic converters and oxygen sensors. Since the oil separator system in the valve cover is not available on its own, and cleaning it is nearly impossible, the complete replacement of the valve cover is the only option. Other oil vent tubes and vacuum hoses are also recommended to get replaced at the same time.

Valve Cover Gaskets. As with any rubber part, failures occur when the rubber becomes dry and brittle. The pliable rubber no longer forms a seal between the cylinder head and valve cover where it will develop an oil leak. Valve cover gaskets that leak can allow oil to seep into the spark plug holes and contaminate ignition coil boots and plugs. That can lead to rough running and misfires. A new valve cover includes new gaskets.

Eccentric Shaft Seal. The seal for the eccentric shaft sensor is a known spot for oil leaks. When the seal to the valve cover fails oil can end up in the sensor itself and ruin the sensor (an unecessary $300 expense). Usually a new seal (o-ring) will stop the leaks but sometimes the valve cover is at fault too. A new eccentric shaft seal is included.

All new hardware is included to avoid re-using and over-tightening the original bolts (they have a very low torque rating).

Replacement requires accessing the rear of the engine with a lot of the upper plastic shrouding removed. The vent hose on the valve cover should be replaced as it is almost always broken anyway (#11157559528). The metal fuel line must also be removed and disconnected from the fuel injectors. Professional installation is encouraged if you have never done this kind of work before. Serious DIY types should have a Bentley Service Manual to use which greatly explains the process. You may also want to combine this work with the oil filter housing gasket replacement.

There is no maintenance or replacement interval for the N52 valve cover. However, we have seen cracks and other failures in the 50,000-90,000 mile range. Our best advice is to plan on a major top end overhaul around the 70-80,000 mile mark. There's no mechanical downside to replacing it as prevention and it will make the engine run better and last longer.

This item fits the following BMWs:
2008-2012 E82 BMW 128i
2007-2011 E90 BMW 328i 328xi 328i xDrive - Sedan
2007-2012 E91 BMW 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2008-2010 E60 BMW 528i 528xi 528i xDrive
2011 F10 BMW 528i
2007-2010 E83 BMW X3 3.0i X3 3.0si
2007-2008 E70 BMW X5 3.0si
2007-2008 E85 BMW Z4 3.0i Z4 3.0si
2009-2010 Z4 BMW Z4 sDrive30i

Includes a full set of injectors (13538616079 x8), seals (13537584315 x8), and decoupling elements (13537564751 x8.) Why replace a full set? Fuel injectors are indexed, meaning they have to be replaced with injectors of the same index number and are not recommended to be replaced individually. This kit addresses the issue with 8 new injectors and decoupling rings.

More on injector indexing:

The index number is found on the head of the injector after the BMW part number.

Example: 13 53 8 616 079-11. "11" is the index number.

Injectors with index 10 and lower have a different calibration and construction than injectors with index 11 and higher. Because of this the injectors with index 10 and lower cannot be mixed with index 11 and higher in the same engine.

This electric valve serves one of several purposes depending on which car it is used on. Please read the application listings below to ensure you are purchasing the correct part. 

Pierburg pumps are some of the most trusted and widely used on the market. From fuel, water, air and vacuum Pierburg has you covered with OE quality and reliable performance year after year.

This item fits the following BMWs:
Secondary Air System Valve
1996-1998 E36 BMW 323is 323ic 328i 328is 328ic M3
1999-3/2003 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2003-2005 E46 BMW 325i 325ci (M56)
1997-2003 E39 BMW 525i 528i 530i 
2000-2006 E53 BMW X5 3.0i 
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i 
1997-2000 Z3 BMW M Roadster M Coupe (S52)

Proper lubrication is essential for the longevity of your turbocharger. This oil supply hose delivers vital oil to the compressor housing, ensuring internal components remain lubricated and protected from premature wear. A leaking or damaged oil line can compromise turbocharger performance and lead to costly repairs—replace it promptly to maintain your vehicle’s reliability.

This premium replacement oil supply hose from Bremmen Parts is engineered for BMW applications, providing an exact fit and seamless installation. Manufactured with OEM-grade precision and materials, it restores proper turbocharger functionality and delivers dependable performance you can trust.