BMW 1 Series E82 (2008-2013)

AeroCatch Racing Hood and Body Panel Fasteners (Pair) - Better than h...

T#:340098

Part#: AEROCATCH

In Stock

$ 566.99

This product was last offered at the strikethrough price on
05-13-2026

Starting at $ 82.99 USD

Add to Wish List

Starting at $ 82.99 USD

Add to Wish List

As used by Turner Motorsport on our championship winning BMW race cars, the new aerodynamically efficient and aesthetically styled AeroCatch is setting new standards in hood fixing for the 21st century. Say goodbye to your standard hood pins -- these are better all around.

Show More Show Less

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E36, E39 ...

T#:389645

Part#: 192416-1J

In Stock

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

KMAC Adjustable Rear Camber And Toe Bushings Set - E82, E89, E9X non-...

T#:389667

Part#: 193926K

In Stock

13% off MSRP $ 480.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 417.00 USD

Limited Qty Sale

Add to Wish List

Qty

13% off MSRP

$ 480.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 417.00 USD

Limited Qty Sale

Add to Wish List

Rear adjustable camber and toe bushings for the E82/E9X non-M 3-series. These bushings allow you to adjust camber and toe beyond factory specs to either restore camber or add more. If you lowered your car and have too much camber these bushings can get you back to stock specs. On the flip side if you need more camber for the track or autocross, you can fine tune it with these too. These bushings press in and replace the existing rubber bushings. They are made from peformance urethane which will give more feedback and response to the driver. Sold as a set with a bushing extraction tool included.

Fits the following BMWs:
E82/88 BMW 2 Series
E89 BMW Z4
E9X BMW Non-M

Show More Show Less

BMC Filter Cleaning Kit

T#:590913

Part#: WA250-500

In Stock

$ 24.99 USD

Add to Wish List

Qty

$ 24.99 USD

Add to Wish List

BMC Performance Air Filter - E90, E91, E92, E93, E89, E60, E61 ...

T#:398689

Part#: FB494/20

In Stock at Vendor

$ 100.99 USD

Add to Wish List

Qty

$ 100.99 USD

Add to Wish List

Looking to upgrade your air filter for increased flow and performance? BMC filter allow significantly higher air flow and are perfectly molded in one piece to fit exactly the same as your stock air filter. These filters are constructed from multi-layerd cotton gauze that is pre-oiled and can be cleaned and regenerated using the BMC regeneration kit.

Show More Show Less

Akrapovic Slip-On Titanium Exhaust System - E82 1M Coupe

T#:340330

Part#: TMS4781

In Stock at Vendor

Sale - Save 4% $ 5,403.99

This product was last offered at the strikethrough price on
07-06-2026

Starting at $ 5,199.79 USD

Add to Wish List

Sale - Save 4%

$ 5,403.99

This product was last offered at the strikethrough price on
07-06-2026

Starting at $ 5,199.79 USD

Add to Wish List

According to BMW the 1 Series M Coupe is a "predator on the prowl", why not give it some GROWL with the Akrapovic slip-on exhaust system.

This slip-on muffler is an "axle back" system that is mounted on the MotoGP 1M Coupe Safety Car and now is available for street going 1M Coupes. The Akrapovic Slip-On Titanium exhaust system for the BMW 1M Coupe is designed for drivers who demand more power and less weight. In addition to a weight reduction and a power gain, one of the tasks of the Akrapovic team was also to make the sound of the 1M Coupe become music to ones ears. An optional wireless "dualmode" exhaust flap control allows the vehicle to have a more civilized, but deeper than stock sound at low speed. However, when the exhaust flap is opened the muffler is bypassed, creating a deep and sporty sound much more in keeping with the personality of the car.

Not for sale outside the US or Canada.

This item fits the following BMWs:
2011+ E82 BMW 1M Coupe

Show More Show Less

BMC Performance Air Filter - E90, E91, E92, E93, E84

T#:398704

Part#: FB630/20

Back Ordered

$ 95.99 USD

Add to Wish List

Qty

$ 95.99 USD

Add to Wish List

Looking to upgrade your air filter for increased flow and performance? BMC filter allow significantly higher air flow and are perfectly molded in one piece to fit exactly the same as your stock air filter. These filters are constructed from multi-layerd cotton gauze that is pre-oiled and can be cleaned and regenerated using the BMC regeneration kit.

Show More Show Less

KMAC Stage 3 Street/Track Front Adjustable Camber/Caster Plates - E36...

T#:389646

Part#: 192416-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 3 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E36...

T#:389647

Part#: 192416-2L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 2 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

BMC Performance Air Filter - E82/8 E9X N52

T#:397417

Part#: FB518/08

Back Ordered

$ 83.99 USD

Add to Wish List

Qty

$ 83.99 USD

Add to Wish List

Looking to upgrade your air filter for increased flow and performance? BMC filter allow significantly higher air flow and are perfectly molded in one piece to fit exactly the same as your stock air filter. These filters are constructed from multi-layerd cotton gauze that is pre-oiled and can be cleaned and regenerated using the BMC regeneration kit.

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

AeroCatch Racing Hood and Body Panel Fasteners (Pair) - Better than h...

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E36, E39 ...

KMAC Adjustable Rear Camber And Toe Bushings Set - E82, E89, E9X non-...

BMC Filter Cleaning Kit

BMC Performance Air Filter - E90, E91, E92, E93, E89, E60, E61 ...

Akrapovic Slip-On Titanium Exhaust System - E82 1M Coupe

BMC Performance Air Filter - E90, E91, E92, E93, E84

KMAC Stage 3 Street/Track Front Adjustable Camber/Caster Plates - E36...

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E36...

BMC Performance Air Filter - E82/8 E9X N52

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results