BMW 1 Series E82 (2008-2013)

Clear BMW chassis

Please ensure your correct model is selected

Sub-Categories

Sort By:

Rogue Engineering - Corporate Logo
T#:641617
Part#: TM
In Stock
$ 69.00 USD
Free Shipping
$ 69.00 USD
Free Shipping
Unlike other aftermarket mounts, the mounting plate and studs of our mounts have been Zinc-plated to prevent corrosion. Rogue Engineering Transmission Mounts are sold as a pair, and come with Grade 8 Zinc plated hardware. Rogue Engineering transmission mounts are designed with street comfort in mind while still reducing left and right movement of the transmission. By using a cylindrical shape instead of the factory hourglass like design and utilizing Neoprene rubber deflection can be significantly reduced, minimizing unwanted transmission movement while maintaining vibration dampening characteristics.
Show More Show Less
Rogue Engineering - Corporate Logo
T#:27105150
Part#: RE.061
In Stock
$ 119.00 USD
Free Shipping
$ 119.00 USD
Free Shipping
You are looking at the BEST license plate bracket for your BMW, price no object! We never understood why BMW would put a cheap, plastic bracket on the back of a BMW to hold a license plate. The screws holding the bracket on would rust, the steel inserts hold the plate on would also rust, causing the hardware holding the plate on to seize or just no longer function. Our bracket fits any BMW that mounts license plates in the rear that use factory part number 51-18-8-238-061. Fits most BMWs produced AFTER 1999. If your vehicle does not use the plastic plate, it will not fit. Does not fit E46 touring (wagon). PROBLEMS with the factory bracket and hardware The screws that secure the plastic bracket are plated steel and will corrode over time. These two screw would normally not be seen since it is under the license plate, but it is holding the bracket onto the trunk. The four (4) nutserts that are pressed into the plastic frame (to hold the license plate) are also steel and will eventually seize with the bolt and just spin in the plastic frame becoming useless. The plastic frame itself is flimsy, doing a near minimal task of holding on the license plate. The hardware securing the plate to the bracket will rust, seizing to the nutsert or even spinning in place becoming completely useless. SOLUTION Create a more robust bracket that would not only be stiffer but also more corrosion resistant; CNC’d aluminum with an anodized finish. We machine a near identical plate, matching factory dimensions, from 1/2" plate of aluminum. Instead of nutserts pressed into plastic, map the correct position and machine the threads for the hardware directly into the plate. The hardware used to secure the new bracket to the trunk would be made from stainless steel (or optional corrosion-proof titanium) The hardware used to secure the license plate to the newly engineered bracket would also be stainless steel (or optional made from titanium) Kit Includes: One (1) Rogue Engineering designed and manufactured CNC'd aluminum license plate bracket Two (2) Stainless screws to secure bracket to trunk. Four (4) stainless screws to secure license plate to bracket.
Show More Show Less
Carbonio No-Drill Front License Plate Mount - North America - Most BM...
For vehicles with Adaptive Cruise Control and M Sport Package
Carbonio - Corporate Logo
T#:599470
Part#: LPM-BMC0136-N
In Stock
$ 139.99 USD
Free Shipping
$ 139.99 USD
Free Shipping
Fitting a front license plate to a BMW requires drilling damaging holes forever ruining the original front bumper. Until now, the only other option was to fit an offset mount to the side using the factory tow hook. Carbonio has now engineered an OEM quality solution that mounts the license plate in the middle while doing no damage of any kind. Installation and removal is a 10-second exercise and the unit is totally self-contained, not requiring any pieces to be fixed to the car. FEATURES NO-DRILL, NO-HOLES, NO-ADHESIVES OR TAPES Easy 10-second-on 10-second-off installation Fully tunable design allows for adjustment of license plate angle and distance forwards / backwards / upwards / downwards Allows for multiple plate mounting location options Great for car shows or track sessions when you want to quickly remove your front plate Soft material on contact surfaces protects grille Strong formed plate support accepts USA and Rest of World (ROW) license plates; a truly global solution Black powder coating offers clean OEM look and long-lasting finish High-speed tested & does not interfere with vehicle cooling, parking sensors, or front cameras Can be used with most license plate frames and clear/colored plate covers and protectors Meets all known international license plate display and mounting laws Unit is shipped pre-assembled with all hardware and is ready to mount out of the box KIT INCLUDES Pre-assembled license plate mount with adjustment tool Complete photographic installation instructions
Show More Show Less

JB Racing - Corporate Logo
T#:2801
Part#: 520-200-240
In Stock
$ 714.00 USD
Free Shipping
$ 714.00 USD
Free Shipping
Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

This JB flywheel replaces the stock flywheel and can be used with either the stock 228mm or stock 240mm clutch discs. Depending on the model you may have either clutch size in your car but this flywheel is compatible with both. You can install a 240mm clutch as a mild upgrade.

Stock Flywheel Weight = 24-31.0lbs
JB Flywheel Weight = 12.0lbs

This item fits the following BMWs:
2006-2010 E60 BMW - 525i, 528i, 530i
2006-2013 E90, E91, E92, E93 BMW - 325i, 328i, 330i
2007-2013 E82 BMW - 125i, 128i
2006-2008 E85, E86 BMW - Z4 3.0i, Z4 3.0si
2009-later E89 BMW - Z4 3.0i
Show More Show Less

Akrapovic - Corporate Logo
T#:340330
Part#: TMS4781
Ships in 6 Business Days
Starting at $ 5,403.80 USD
Free Shipping
Starting at $ 5,403.80 USD
Free Shipping
According to BMW the 1 Series M Coupe is a "predator on the prowl", why not give it some GROWL with the Akrapovic slip-on exhaust system.

This slip-on muffler is an "axle back" system that is mounted on the MotoGP 1M Coupe Safety Car and now is available for street going 1M Coupes. The Akrapovic Slip-On Titanium exhaust system for the BMW 1M Coupe is designed for drivers who demand more power and less weight. In addition to a weight reduction and a power gain, one of the tasks of the Akrapovic team was also to make the sound of the 1M Coupe become music to ones ears. An optional wireless "dualmode" exhaust flap control allows the vehicle to have a more civilized, but deeper than stock sound at low speed. However, when the exhaust flap is opened the muffler is bypassed, creating a deep and sporty sound much more in keeping with the personality of the car.

Not for sale outside the US or Canada.

This item fits the following BMWs:
2011+ E82 BMW 1M Coupe
Show More Show Less
Rogue Engineering - Corporate Logo
T#:553830
Part#: RE.E9X.TA.M3
Ships in 9 Business Days
$ 289.00 USD
Free Shipping
$ 289.00 USD
Free Shipping

When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.

This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear. 

Features:

  • 100% machined and anodized, 6061-T6 lightweight aluminum arms
  • High-strength, 3-piece, rod end (with carbon fiber reinforced, PTFE race) offers longer life for street compared to standard rod ends
  • SEALS-IT Rod end seals keep dirt, water, and other contaminants out
  • Rod ends feature grease fittings, to allow for rod end serviceability.
  • Lighter than stock!  (Stock is 875g, RE arms are 640g)
  • Extremely easy installation and adjustment (your alignment shop will LOVE you!)
Show More Show Less

Rogue Engineering - Corporate Logo
T#:553834
Part#: RE.E9X.TA
Back Ordered
$ 339.00 USD
Free Shipping
$ 339.00 USD
Free Shipping

Updated design!  Now shipping!

When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.

This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear. 

Features:

100% machined and anodized, 6061-T6 lightweight aluminum arms (and collars).

Stainless hardware and spacers are perfect for the tough Northeast climate!

New!  Easy adjustment with 22mm open ended wrench and 5mm allen key!  It only requires 15 ft. lbs. on the clamp to secure the clamp!

New!  Included lock-out kit, replaces factory eccentric hardware.

Updated 3-piece rod ends features 4130 chromoly steel bodies, heat-treated, alloy steel races, and Teflon liners

Extremely easy installation and adjustment (your alignment shop will LOVE you!)

Show More Show Less